floppy gone missing
Lawrence MacIntyre
macintyrelp at ornl.gov
Mon Feb 14 14:59:27 UTC 2005
Hi:
My floppy drive recently disappeared from Ubuntu. It's just a generic
ide floppy. I reseated all of the cables, but it stayed gone. Then I
booted Knoppix 3.7 to see if it was hardware or software, and the floppy
is present with Knoppix. Does anyone have any ideas?
I've attached dmesg output and the contents of /proc/ide in case that
helps.
--
Lawrence MacIntyre 865.574.8696 macintyrelp at ornl.gov
Oak Ridge National Laboratory
High Performance Information Infrastructure Technology Group
AKO: lawrence.macintyre at us.army.mil
SIPRNet: macintyrelp at ornl.doe.sgov.gov
-------------- next part --------------
16028k reserved, 690k data, 140k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5570.56 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2806.0102 MHz.
..... host bus clock speed is 133.0623 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4360k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb340, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Uncovering SIS963 that hid as a SIS503 (compatible=1)
Enabling SiS 96x SMBus.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbdd0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbe00, dseg 0xf0000
pnp: 00:0b: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0b: ioport range 0x10c0-0x10df has been reserved
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 17 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 217
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 19 (level, low) -> IRQ 225
ACPI: PCI interrupt 0000:00:0c.1[B] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:0c.2[C] -> GSI 16 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178014
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0014
.... register #02: 02000000
....... : arbitration: 02
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 B1
11 001 01 1 1 0 1 0 1 1 A9
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 E1
14 001 01 1 1 0 1 0 1 1 C1
15 001 01 1 1 0 1 0 1 1 C9
16 001 01 1 1 0 1 0 1 1 D1
17 001 01 1 1 0 1 0 1 1 D9
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ177 -> 0:16
IRQ169 -> 0:17
IRQ185 -> 0:18
IRQ225 -> 0:19
IRQ193 -> 0:20
IRQ201 -> 0:21
IRQ209 -> 0:22
IRQ217 -> 0:23
.................................... done.
PCI: Cannot allocate resource region 4 of device 0000:00:02.1
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices:
FUTS PCI0 USB0 USB1 USB2 USB3 AMR0 UAR1 PS2M PS2K
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4360 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 140k freed
vesafb: probe of vesafb0 failed with error -6
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (40 C)
ACPI: Fan [FAN] (on)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
ACPI: PCI interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 177
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0x4000-0x4007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x4008-0x400f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y080L0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 >
hdc: LITEON DVD-ROM LTD163D, ATAPI CD/DVD-ROM drive
hdd: OPTORITE CD-RW CW4002, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2048272k swap on /dev/hda3. Priority:-1 extents:1
EXT3 FS on hda5, internal journal
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
lp: driver loaded but no devices found
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6111 Tue Jul 27 07:55:38 PDT 2004
i2c-sis96x version 1.0.0
sis96x smbus 0000:00:02.1: SiS96x SMBus base address: 0x1040
loop: loaded (max 8 devices)
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 648 chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xd0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
ACPI: PCI interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 169
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[169] MMIO=[ea020000-ea0207ff] Max Packet=[2048]
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 185
intel8x0_measure_ac97_clock: measured 49632 usecs
intel8x0: clocking to 48000
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000301b1c6574]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 193
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller
ohci_hcd 0000:00:03.0: irq 193, pci mem f8b75000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 201
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
ohci_hcd 0000:00:03.1: irq 201, pci mem f8b77000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 209
ohci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
ohci_hcd 0000:00:03.2: irq 209, pci mem f8b79000
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 19 (level, low) -> IRQ 225
ohci_hcd 0000:00:0c.0: NEC Corporation USB
ohci_hcd 0000:00:0c.0: irq 225, pci mem f8b85000
ohci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:0c.1[B] -> GSI 18 (level, low) -> IRQ 185
ohci_hcd 0000:00:0c.1: NEC Corporation USB (#2)
ohci_hcd 0000:00:0c.1: irq 185, pci mem f8b87000
ohci_hcd 0000:00:0c.1: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 217
ehci_hcd 0000:00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 0000:00:03.3: irq 217, pci mem f8b89000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 6
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 6 ports detected
ACPI: PCI interrupt 0000:00:0c.2[C] -> GSI 16 (level, low) -> IRQ 177
ehci_hcd 0000:00:0c.2: NEC Corporation USB 2.0
ehci_hcd 0000:00:0c.2: irq 177, pci mem f8b8b000
ehci_hcd 0000:00:0c.2: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:0c.2: USB 2.0 enabled, EHCI 0.95, driver 2004-May-10
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 5 ports detected
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp: pci dev 0000:00:0b.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 18 (level, low) -> IRQ 185
eth0: RealTek RTL8139 at 0xec00, 00:40:f4:72:8f:41, IRQ 185
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02eb8a0(lo)
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [FUTS]
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04Aborted Command
hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdd: drive_cmd: error=0x04Aborted Command
eth0: no IPv6 routers present
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 16x mode
agpgart: SiS delay workaround: giving bridge time to recover.
agpgart: Putting AGP V3 device at 0000:01:00.0 into 16x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 16x mode
agpgart: SiS delay workaround: giving bridge time to recover.
agpgart: Putting AGP V3 device at 0000:01:00.0 into 16x mode
-------------- next part --------------
0
/proc/ide/ide1/hdd/capacity
OPTORITE CD-RW CW4002
/proc/ide/ide1/hdd/model
cdrom
/proc/ide/ide1/hdd/media
ide-cdrom version 4.61
/proc/ide/ide1/hdd/driver
0
/proc/ide/ide1/hdc/capacity
LITEON DVD-ROM LTD163D
/proc/ide/ide1/hdc/model
cdrom
/proc/ide/ide1/hdc/media
ide-cdrom version 4.61
/proc/ide/ide1/hdc/driver
pci
/proc/ide/ide1/model
ide0
/proc/ide/ide1/mate
pci bus 00 device 15 vendor 1039 device 5513 channel 1
39 10 13 55 05 00 10 02 00 80 01 01 00 80 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01 40 00 00 00 00 00 00 00 00 00 00 39 10 13 55
00 00 00 00 58 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 20 00 06 00 00 00 00 00
f2 00 f3 00 ea 96 d5 d0 01 00 02 86 00 00 00 00
ff aa ff 00 00 00 00 00 00 00 00 00 00 00 00 00
1f 32 09 05 00 60 1c 1e 56 23 06 04 56 23 06 04
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
/proc/ide/ide1/config
1
/proc/ide/ide1/channel
Maxtor 6Y080L0
/proc/ide/ide0/hda/model
disk
/proc/ide/ide0/hda/media
ide-disk version 1.18
/proc/ide/ide0/hda/driver
pci
/proc/ide/ide0/model
ide1
/proc/ide/ide0/mate
pci bus 00 device 15 vendor 1039 device 5513 channel 0
39 10 13 55 05 00 10 02 00 80 01 01 00 80 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01 40 00 00 00 00 00 00 00 00 00 00 39 10 13 55
00 00 00 00 58 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 20 00 06 00 00 00 00 00
f2 00 f3 00 ea 96 d5 d0 01 00 02 86 00 00 00 00
ff aa ff 00 00 00 00 00 00 00 00 00 00 00 00 00
1f 32 09 05 00 60 1c 1e 56 23 06 04 56 23 06 04
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
/proc/ide/ide0/config
0
/proc/ide/ide0/channel
SiS 5513 Ultra 133 chipset
--------------- Primary Channel ---------------- Secondary Channel -------------
Channel Status: On On
Operation Mode: Compatible Compatible
Cable Type: 80 pins 40 pins
Drive 0:
UDMA Enabled UDMA Enabled
UDMA Cycle Time 2 CLK UDMA Cycle Time 6 CLK
Drive 1:
UDMA Disabled UDMA Enabled
UDMA Cycle Time Reserved UDMA Cycle Time 6 CLK
/proc/ide/sis
ide-cdrom version 4.61
ide-disk version 1.18
/proc/ide/drivers
More information about the ubuntu-users
mailing list