Gnome baker error/problem

[Sebastian Spiess]

Can someone help me with this?

I was burning a audio CD with gnome baker, I mean I tried.


I had problems writing DVDs as well but can't remember the exact error.

When i use the internal data disc writer it works?

I tryed serpentine and it worked.

Has it something to do with permissions? I installed gnome baker via the "Add/Remove software" so I think it should setup 
properly...

I read something about my drive on http://gentoo-wiki.com/HARDWARE_Toshiba_Satellite_P100#Linux_Support
"Add combined_mode=libata to kernel parameters in order to setup dma transfers for optical drive. Otherwise, playing or 
recording DVDs doesn't work correctly."

But I am not sure how to do that properly. Can one give me instructions


Cheers Sebastian



> wodim: No write mode specified.
> wodim: Asuming -tao mode.
> wodim: Future versions of wodim may have different drive dependent defaults.
> scsidev: '1,0,0'
> scsibus: 1 target: 0 lun: 0
> Linux sg driver version: 3.5.34
> Wodim version: 1.1.2
> SCSI buffer size: 64512
> Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
> communication breaks or freezes immediately after that.
> TOC Type: 0 = CD-DA
> Driveropts: 'burnfree'
> atapi: 1
> Device type    : Removable CD-ROM
> Version        : 5
> Response Format: 2
> Capabilities   : 
> Vendor_info    : 'HL-DT-ST'
> Identification : 'DVDRAM GMA-4082N'
> Revision       : 'HV02'
> Device seems to be: Generic mmc2 DVD-R/DVD-RW.
> Current: 0x0009 (CD-R)
> Profile: 0x0012 (DVD-RAM) 
> Profile: 0x0011 (DVD-R sequential recording) 
> Profile: 0x0015 (DVD-R/DL sequential recording) 
> Profile: 0x0014 (DVD-RW sequential recording) 
> Profile: 0x0013 (DVD-RW restricted overwrite) 
> Profile: 0x001A (DVD+RW) 
> Profile: 0x001B (DVD+R) 
> Profile: 0x002B (DVD+R/DL) 
> Profile: 0x0010 (DVD-ROM) 
> Profile: 0x0009 (CD-R) (current)
> Profile: 0x000A (CD-RW) 
> Profile: 0x0008 (CD-ROM) 
> Profile: 0x0002 (Removable disk) 
> Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
> Driver flags   : MMC-3 SWABAUDIO BURNFREE 
> Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
> Drive buf size : 1053696 = 1029 KB
> Drive DMA Speed: 13496 kB/s 76x CD 9x DVD
> FIFO size      : 12582912 = 12288 KB
> 
> Speed set to 4234 KB/s
> Lout start:      805 MB (79:46/22) = 358822 sectors
> Current Secsize: 2048
> ATIP info from disk:
>   Indicated writing power: 5
>   Is not unrestricted
>   Is not erasable
>   Disk sub type: Medium Type A, high Beta category (A+) (3)
>   ATIP start of lead in:  -11634 (97:26/66)
>   ATIP start of lead out: 359846 (79:59/71)
> Disk type:    Short strategy type (Phthalocyanine or similar)
> Manuf. index: 3
> Manufacturer: CMC Magnetics Corporation
> Blocks total: 359846 Blocks current: 359846 Blocks remaining: 1024
> Starting to write CD/DVD at speed  24.0 in real TAO mode for single session.
> Last chance to quit, starting real write in 5 seconds.   4 seconds.   3 seconds.   2 seconds.   1 seconds.   0 seconds. Operation starts.
> Waiting for reader process to fill input buffer ... input buffer ready.
> Performing OPC...
> Starting new track at sector: 0
> Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
> CDB:  2A 00 00 00 00 87 00 00 1B 00
> status: 0x2 (CHECK CONDITION)
> Sense Bytes: 70 00 05 00 00 00 00 10 2A 30 02 80 21 02 00 00
> Sense Key: 0x5 Illegal Request, Segment 0
> Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
> Sense flags: Blk 0 (not valid) 
> resid: 63504
> cmd finished after 0.002s timeout 40s
> wodim: The current problem looks like a buffer underrun.
> wodim: It looks like 'driveropts=burnfree' does not work for this drive.
> wodim: Please report.
> wodim: Make sure that you are root, enable DMA and check your HW/OS set up.
> 
> write track data: error after 317520 bytes
> Writing  time:   15.909s
> Average write speed 301.8x.
> Fixating...
> Fixating time:   27.356s