lifeview pci trio (saa7134) not working through diseqc anymore

Jordi Moles Blanco jordi at cdmon.com
Wed Dec 10 16:16:12 UTC 2008


Hi everyone,

i've got 2 satellite dishes home and a diseqc 2.0.

i've been using ubuntu/kubuntu for quite a while now but until hardy 
came out, i couldn't use my "lifeview pci trio" pci card at all, as i 
want it to work throught diseqc, to get channels from both dishes, so i 
kept going back to windows, unfortunately.

The thing is that my whole setup works, as i've got a machine with dual 
boot and window xp installed on one partition. Needless to say that i 
can , with prodvb, altdvb, etc, tune both satellites through diseqc.

so... when hardy came out i decided to try again... i downloaded the cd, 
i386 version and installed. I almost went crazy when i launched kaffeine 
and i was able to tune channels from both satellites... almost out of 
the box!!! i hadn't been able to do this in earlier versions (well... a 
part from having to call modprobe saa7134 front_end=1 to use the 
satellite chip)

so... i searched for all the channels with kaffeine and i started 
watching channels without any problem.

Then, i had the bad idea of doing

apt-get update
apt-get upgrade

i didn't get any error message at all... but when i ran kaffeine 
again..... no channels could be viewed.

Then i started to go crazy trying to get it working again. I deleted the 
whole list of channels and tried to tune again... with no luck... i 
would only get channels from one satellite, that on on switch 1 in the 
diseqc.

After 2 days i loaded windows to see if i had broken something... but i 
hadn't, everything was working fine there.

then i loaded the old kernel, linux-image-2.6.24-19-generic, then the 
updated one again linux-image-2.6.24-22-generic

then i tried to go back to an earlier version of kaffeine (just in case)

i'm using 0.8.6-0ubuntu8.3 and i went back to 0.8.6-0ubuntu8.1 and even 
0.8.6-0ubuntu8

no luck with all that.

and then i found out how to scan channels from command line, and i saw 
that no matter what switch you tell saa7134 to scan on, i will always go 
to "switch 1" on the diseqc.

here's what i got from scanning........

switch 1 (astra 28.2E)

********
scan -s 1 /home/servidor/.kde/share/apps/kaffeine/dvb-s/Astra-28.2E
 >>> tune to: 10729:v:1:22000
0x0000 0x206c: pmt_pid 0x0100 BSkyB -- E4+1 (running)
0x0000 0x2071: pmt_pid 0x0103 BSkyB -- E4 (running)
0x0000 0x2077: pmt_pid 0x0101 BSkyB -- Channel 4 +1 (running)
0x0000 0x2078: pmt_pid 0x0102 BSkyB -- Channel 4 +1 (running)
0x0000 0x2079: pmt_pid 0x010f BSkyB -- Channel 4 +1 (running)
0x0000 0x207a: pmt_pid 0x0107 BSkyB -- Channel 4 +1 (running)
0x0000 0x207b: pmt_pid 0x0108 BSkyB -- Channel 4 +1 (running, scrambled)
0x0000 0x207c: pmt_pid 0x010a BSkyB -- Channel 4 +1 (running)
0x0000 0x2094: pmt_pid 0x010c BSkyB -- More4 (running)
0x0000 0x20c5: pmt_pid 0x0106 BSkyB -- 8389 (running, scrambled)
0x0000 0x23f7: pmt_pid 0x0104 BSkyB -- c4 l +1 (running)
0x0000 0x23f8: pmt_pid 0x0109 BSkyB -- e4 (running)
********

switch 2 (astra 19E)
********
scan -s 2 /home/servidor/.kde/share/apps/kaffeine/dvb-s/Astra-19.2E
 >>> tune to: 10788:v:2:22000
0x0000 0x283d: pmt_pid 0x0100 BSkyB -- BBC 1 W Mids (running)
0x0000 0x283e: pmt_pid 0x0101 BSkyB -- BBC 1 N West (running)
0x0000 0x283f: pmt_pid 0x0102 BSkyB -- BBC 1 Yrks&Lin (running)
0x0000 0x2840: pmt_pid 0x0103 BSkyB -- BBC 1 Yorks (running)
0x0000 0x2841: pmt_pid 0x0104 BSkyB -- BBC 1 E Mids (running)
0x0000 0x2842: pmt_pid 0x0105 BSkyB -- BBC 1 East (E) (running)
0x0000 0x2851: pmt_pid 0x0106 BSkyB -- ETV5 (running)
********

And this is the problem!!! on Astra-19.2 there's no "BBC 1 W Mids". It's 
getting signal from switch 1 and scanning from the correct transponders 
list on  /home/servidor/.kde/share/apps/kaffeine/dvb-s/Astra-19.2E

And it doesn't matter if i run "scan -s 1" or "scan -s 2" or "scan -s 
3", it will always scan from "switch 1"

through kaffeine i get to the same point, i get a scan on swith 1 only.

is this a bug? has anyone experienced this? is there a warkaround for 
this? how could i get it working in the first place?
what could i break by upgrading the system?

Please, let me know if i can provide any further information.

here are my system details:

********
# lsb_release -rd

Description:    Ubuntu 8.04.1
Release:        8.04
**********

i've looked through the system logs and i can't find anything, nothing 
related to diseqc or kaffeine, there seem to be no errors with those words.

Thanks.




More information about the kubuntu-users mailing list