[Bug 31887] Cannot Enable DMA on Hard Drives after upgrade to Dapper Drake
Chris Murphy
chrismurf at gmail.com
Sat Feb 18 16:38:20 UTC 2006
Public bug reported:
https://launchpad.net/malone/bugs/31887
Affects: linux-source-2.6.15 linux-image-2.6.15-15-386 (Ubuntu)
Severity: Normal
Priority: (none set)
Status: Unconfirmed
Description:
After upgrading to Dapper Drake, DMA is now not enabled on some of my
hard drives. I cannot enable it with hdparm; it returns as shown below.
chris at murf-box:~$ sudo hdparm -d1 /dev/hda
/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
Oddly enough, my /dev/hdg drive works fine, it's just /dev/hda and
/dev/hdb that seem to be at fault. I think PDC202XX_NEW takes care of
HDG. I believe that perhaps there is not support for my motherboard /
North Bridge, which controls the primary IDE interface perhaps? My
Motherboard is a Gigabyte GA-7VAXP with a Via KT400 North Bridge.
This was not a problem with Breezy. I have pasted a whole buncha
potential debug info below.
===LSPCI===
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge
0000:00:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
0000:00:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
0000:00:0f.0 RAID bus controller: Promise Technology, Inc. PDC20276 (MBFastTrak133 Lite) (rev 01)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80)
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
0000:00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
0000:00:14.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti 4400] (rev a2)
===DMESG===
kernel memory: 256k freed
[4294669.334000] vesafb: framebuffer at 0xd8000000, mapped to 0x80880000, using 5120k, total 131072k
[4294669.334000] vesafb: mode is 1280x1024x16, linelength=2560, pages=1
[4294669.334000] vesafb: protected mode interface info at c000:e910
[4294669.334000] vesafb: scrolling: redraw
[4294669.334000] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[4294669.334000] vesafb: Mode is VGA compatible
[4294669.404000] Console: switching to colour frame buffer device 160x64
[4294669.404000] fb0: VESA VGA frame buffer device
[4294670.512000] Capability LSM initialized
[4294670.549000] ACPI: Processor [CPU0] (supports 2 throttling states)
[4294670.991000] PDC20276: IDE controller at PCI slot 0000:00:0f.0
[4294670.991000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 19 (level, low) -> IRQ 169
[4294670.991000] PDC20276: chipset revision 1
[4294670.991000] PDC20276: 100% native mode on irq 169
[4294670.991000] ide2: BM-DMA at 0xd000-0xd007, BIOS settings: hde:pio, hdf:pio
[4294670.991000] ide3: BM-DMA at 0xd008-0xd00f, BIOS settings: hdg:pio, hdh:pio
[4294670.991000] Probing IDE interface ide2...
[4294671.510000] Probing IDE interface ide3...
[4294671.774000] hdg: Maxtor 6Y080P0, ATA DISK drive
[4294672.386000] ide3 at 0xc800-0xc807,0xcc02 on irq 169
[4294675.592000] Probing IDE interface ide0...
[4294675.978000] hda: WDC WD800JB-00CRA1, ATA DISK drive
[4294676.233000] hdb: ST3160023A, ATA DISK drive
[4294676.284000] Probing IDE interface ide1...
[4294677.078000] hdc: SAMSUNG CD-R/RW SW-232B, ATAPI CD/DVD-ROM drive
[4294677.792000] hdd: SONY DVD RW DRU-800A, ATAPI CD/DVD-ROM drive
[4294677.843000] Probing IDE interface ide2...
[4294678.362000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294678.362000] ide1 at 0x170-0x177,0x376 on irq 15
[4294678.370000] hdg: max request size: 128KiB
[4294678.383000] hdg: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133)
[4294678.384000] hdg: cache flushes supported
[4294678.384000] hdg: hdg1
[4294678.390000] hda: max request size: 128KiB
[4294678.403000] hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63
[4294678.403000] hda: cache flushes not supported
[4294678.404000] hda: hda1 hda2 hda3
[4294678.435000] hdb: max request size: 1024KiB
[4294678.435000] hdb: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63
[4294678.435000] hdb: cache flushes supported
[4294678.435000] hdb: hdb1
[4294678.467000] hdc: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache
[4294678.467000] Uniform CD-ROM driver Revision: 3.20
[4294678.489000] hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[4294678.857000] VP_IDE: IDE controller at PCI slot 0000:00:11.1
[4294678.857000] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[4294678.857000] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[4294678.857000] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 177
[4294678.857000] PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 1
[4294678.857000] VP_IDE: chipset revision 6
[4294678.857000] VP_IDE: not 100% native mode: will probe irqs later
[4294678.857000] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
[4294678.857000] VP_IDE: port 0x01f0 already claimed by ide0
[4294678.857000] VP_IDE: port 0x0170 already claimed by ide1
[4294678.857000] VP_IDE: neither IDE port enabled (BIOS)
[4294678.904000] usbcore: registered new driver usbfs
[4294678.905000] usbcore: registered new driver hub
[4294678.907000] USB Universal Host Controller Interface driver v2.3
[4294678.907000] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
[4294678.907000] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[4294678.907000] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[4294678.907000] PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 9
[4294678.907000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[4294678.908000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[4294678.908000] uhci_hcd 0000:00:10.0: irq 185, io base 0x0000d400
[4294678.908000] hub 1-0:1.0: USB hub found
[4294678.908000] hub 1-0:1.0: 2 ports detected
[4294679.009000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[4294679.009000] PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 9
[4294679.009000] uhci_hcd 0000:00:10.1: UHCI Host Controller
[4294679.009000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[4294679.009000] uhci_hcd 0000:00:10.1: irq 185, io base 0x0000d800
[4294679.009000] hub 2-0:1.0: USB hub found
[4294679.009000] hub 2-0:1.0: 2 ports detected
[4294679.110000] ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[4294679.110000] PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 9
[4294679.110000] uhci_hcd 0000:00:10.2: UHCI Host Controller
[4294679.110000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[4294679.110000] uhci_hcd 0000:00:10.2: irq 185, io base 0x0000dc00
[4294679.110000] hub 3-0:1.0: USB hub found
[4294679.110000] hub 3-0:1.0: 2 ports detected
[4294679.213000] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 185
[4294679.213000] PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9
[4294679.213000] ehci_hcd 0000:00:10.3: EHCI Host Controller
[4294679.213000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[4294679.213000] ehci_hcd 0000:00:10.3: irq 185, io mem 0xea006000
[4294679.213000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[4294679.214000] hub 4-0:1.0: USB hub found
[4294679.214000] hub 4-0:1.0: 6 ports detected
[4294679.215000] usb 1-1: new full speed USB device using uhci_hcd and address 2
[4294679.452000] EXT3-fs: mounted filesystem with ordered data mode.
[4294679.453000] kjournald starting. Commit interval 5 seconds
[4294680.313000] usb 1-1: new full speed USB device using uhci_hcd and address 3
[4294680.447000] hub 1-1:1.0: USB hub found
[4294680.449000] hub 1-1:1.0: 3 ports detected
[4294680.763000] usb 1-2: new full speed USB device using uhci_hcd and address 4
[4294681.061000] usb 1-1.1: new full speed USB device using uhci_hcd and address 5
[4294681.327000] usb 1-1.2: new low speed USB device using uhci_hcd and address 6
[4294690.805000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294690.821000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[4294691.116000] Linux video capture interface: v1.00
[4294691.138000] Linux agpgart interface v0.101 (c) Dave Jones
[4294691.256000] bttv: driver version 0.9.16 loaded
[4294691.256000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[4294691.257000] bttv: Bt8xx card found (0).
[4294691.257000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 169
[4294691.257000] bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 169, latency: 32, mmio: 0xea005000
[4294691.257000] bttv0: detected: ATI TV Wonder/VE [card=64], PCI subsystem ID is 1002:0003
[4294691.257000] bttv0: using: ATI TV-Wonder VE [card=64,autodetected]
[4294691.257000] bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
[4294691.262000] bttv0: using tuner=19
[4294691.262000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[4294691.264000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[4294691.266000] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[4294691.276000] agpgart: Detected VIA KT400/KT400A/KT600 chipset
[4294691.286000] agpgart: AGP aperture is 128M @ 0xd0000000
[4294691.512000] usbcore: registered new driver hiddev
[4294691.882000] Real Time Clock Driver v1.12
[4294691.917000] input: PC Speaker as /class/input/input0
[4294692.024000] Floppy drive(s): fd0 is 1.44M
[4294692.039000] FDC 0 is a post-1991 82077
[4294692.135000] tuner 0-0060: All bytes are equal. It is not a TEA5767
[4294692.135000] tuner 0-0060: chip found @ 0xc0 (bt878 #0 [sw])
[4294692.137000] tuner 0-0060: type set to 19 (Temic PAL* auto (4006 FN5))
[4294692.171000] bttv0: registered device video0
[4294692.172000] bttv0: registered device vbi0
[4294692.172000] bttv0: PLL: 28636363 => 35468950 .. ok
[4294692.213000] nvidia: module license 'NVIDIA' taints kernel.
[4294692.225000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 193
[4294692.225000] NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:22:51 PST 2005
[4294692.269000] bt878: AUDIO driver version 0.0.0 loaded
[4294692.270000] bt878: Bt878 AUDIO function found (0).
[4294692.270000] ACPI: PCI Interrupt 0000:00:0b.1[A] -> GSI 19 (level, low) -> IRQ 169
[4294692.270000] bt878(0): Bt878 (rev 17) at 00:0b.1, irq: 169, latency: 32, memory: 0xea004000
[4294692.561000] irda_init()
[4294692.561000] NET: Registered protocol family 23
[4294692.580000] 8139too Fast Ethernet driver 0.9.27
[4294692.580000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 201
[4294692.580000] eth0: RealTek RTL8139 at 0x80e4c000, 00:20:ed:46:a2:74, IRQ 201
[4294692.580000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[4294692.604000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[4294692.705000] ieee1394: Initialized config rom entry `ip1394'
[4294692.717000] ohci1394: $Rev: 1313 $ Ben Collins <bcollins at debian.org>
[4294692.717000] ACPI: PCI Interrupt 0000:00:14.0[A] -> GSI 16 (level, low) -> IRQ 193
[4294692.717000] PCI: Via IRQ fixup for 0000:00:14.0, from 10 to 1
[4294692.771000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[193] MMIO=[ea008000-ea0087ff] Max Packet=[2048]
[4294692.854000] parport: PnPBIOS parport detected.
[4294692.854000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[4294693.244000] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
[4294693.244000] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[4294693.244000] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 209
[4294693.244000] PCI: Via IRQ fixup for 0000:00:11.5, from 10 to 1
[4294693.245000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[4294693.998000] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[4294694.094000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000020ed0046a29c]
[4294694.128000] NET: Registered protocol family 17
[4294698.523000] NET: Registered protocol family 10
[4294698.523000] lo: Disabled Privacy Extensions
[4294698.523000] IPv6 over IPv4 tunneling driver
[4294701.518000] drivers/usb/input/hid-core.c: timeout initializing reports
[4294701.518000]
[4294701.518000] input: NMB Dell USB 7HK Keyboard as /class/input/input1
[4294701.518000] input: USB HID v1.00 Keyboard [NMB Dell USB 7HK Keyboard] on usb-0000:00:10.0-1.1
[4294701.526000] input: NMB Dell USB 7HK Keyboard as /class/input/input2
[4294701.526000] input,hiddev96: USB HID v1.00 Device [NMB Dell USB 7HK Keyboard] on usb-0000:00:10.0-1.1
[4294701.547000] input: Logitech USB Receiver as /class/input/input3
[4294701.547000] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:10.0-1.2
[4294701.600000] input: Logitech USB Receiver as /class/input/input4
[4294701.600000] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-1.2
[4294701.600000] usbcore: registered new driver usbhid
[4294701.600000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[4294701.602000] quickcam: QuickCam USB camera found (driver version QuickCam USB 0.6.3 $Date: 2005/04/15 19:32:49 $)
[4294701.602000] quickcam: Kernel:2.6.15-15-386 bus:1 class:FF subclass:FF vendor:046D product:0870
[4294701.610000] quickcam: Sensor HDCS-1020 detected
[4294701.612000] quickcam: Registered device: /dev/video1
[4294701.612000] usbcore: registered new driver quickcam
[4294701.737000] ts: Compaq touchscreen protocol output
[4294702.218000] lp0: using parport0 (interrupt-driven).
[4294702.342000] SCSI subsystem initialized
[4294702.356000] sbp2: $Rev: 1306 $ Ben Collins <bcollins at debian.org>
[4294702.356000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[4294702.356000] ieee1394: sbp2: Try serialize_io=0 for better performance
[4294702.514000] Adding 1477972k swap on /dev/hda3. Priority:-1 extents:1 across:1477972k
[4294702.697000] EXT3 FS on hda2, internal journal
[4294702.903000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294702.903000] md: bitmap version 4.39
[4294703.471000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
[4294703.991000] cdrom: open failed.
[4294705.151000] cdrom: open failed.
[4294709.139000] eth0: no IPv6 routers present
[4294733.116000] NTFS driver 2.1.25 [Flags: R/O MODULE].
[4294733.219000] NTFS volume version 3.1.
[4294733.242000] kjournald starting. Commit interval 5 seconds
[4294733.242000] EXT3 FS on hdg1, internal journal
[4294733.242000] EXT3-fs: mounted filesystem with ordered data mode.
[4294733.265000] kjournald starting. Commit interval 5 seconds
[4294733.266000] EXT3 FS on hdb1, internal journal
[4294733.266000] EXT3-fs: mounted filesystem with ordered data mode.
[4294740.549000] ACPI: Power Button (FF) [PWRF]
[4294740.549000] ACPI: Power Button (CM) [PWRB]
[4294740.681000] ibm_acpi: ec object not found
[4294750.567000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[4294750.567000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[4294750.568000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[4294751.212000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[4294751.212000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[4294751.212000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[4294754.878000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[4294754.879000] apm: overridden by ACPI.
[4294756.913000] hdc: drive_cmd: status=0x41 { DriveReady Error }
[4294756.913000] hdc: drive_cmd: error=0x04 { AbortedCommand }
[4294756.913000] ide: failed opcode was: 0xec
[4294756.923000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294756.923000] hdd: drive_cmd: error=0x04 { AbortedCommand }
[4294756.923000] ide: failed opcode was: 0xec
[4294756.956000] hdc: drive_cmd: status=0x41 { DriveReady Error }
[4294756.956000] hdc: drive_cmd: error=0x04 { AbortedCommand }
[4294756.956000] ide: failed opcode was: 0xec
[4294756.960000] hdc: drive_cmd: status=0xd0 { Busy }
[4294756.960000] ide: failed opcode was: 0xa1
[4294756.968000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
[4294756.968000] hdd: drive_cmd: error=0x04 { AbortedCommand }
[4294756.968000] ide: failed opcode was: 0xec
[4294758.151000] Bluetooth: Core ver 2.8
[4294758.151000] NET: Registered protocol family 31
[4294758.151000] Bluetooth: HCI device and connection manager initialized
[4294758.151000] Bluetooth: HCI socket layer initialized
[4294758.195000] Bluetooth: L2CAP ver 2.8
[4294758.195000] Bluetooth: L2CAP socket layer initialized
[4294758.275000] Bluetooth: RFCOMM socket layer initialized
[4294758.275000] Bluetooth: RFCOMM TTY layer initialized
[4294758.275000] Bluetooth: RFCOMM ver 1.6
[4295173.841000] NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437. You might want to try to use the mount option nls=utf8.
[4295173.847000] NTFS-fs warning (device hda1): ntfs_filldir(): Skipping unrepresentable inode 0x57ba.
[4295192.906000] NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437. You might want to try to use the mount option nls=utf8.
[4295192.907000] NTFS-fs warning (device hda1): ntfs_filldir(): Skipping unrepresentable inode 0x606a.
===LSMOD===
Module Size Used by
isofs 37688 1
udf 88452 0
binfmt_misc 12296 1
rfcomm 39704 0
l2cap 26372 5 rfcomm
bluetooth 49892 4 rfcomm,l2cap
cpufreq_userspace 4696 0
cpufreq_stats 5636 0
freq_table 4740 1 cpufreq_stats
cpufreq_powersave 1920 0
cpufreq_ondemand 6428 0
cpufreq_conservative 7332 0
video 16260 0
tc1100_wmi 6916 0
sony_acpi 5516 0
pcc_acpi 11136 0
hotkey 11556 0
dev_acpi 11140 0
container 4608 0
button 6672 0
acpi_sbs 19980 0
battery 9988 1 acpi_sbs
ac 5252 1 acpi_sbs
i2c_acpi_ec 5120 1 acpi_sbs
nls_cp437 5888 1
ntfs 103536 1
dm_mod 58936 1
md_mod 72532 0
sr_mod 16932 0
sbp2 24580 0
scsi_mod 138856 2 sr_mod,sbp2
lp 11844 0
tsdev 8000 0
ipv6 265600 8
af_packet 22920 2
snd_seq_dummy 3844 0
snd_seq_oss 33536 0
snd_seq_midi 9376 0
snd_seq_midi_event 7552 2 snd_seq_oss,snd_seq_midi
snd_seq 51984 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_via82xx 28696 1
snd_ac97_codec 92448 1 snd_via82xx
snd_ac97_bus 2304 1 snd_ac97_codec
snd_pcm_oss 53664 0
snd_mixer_oss 18688 1 snd_pcm_oss
snd_pcm 89736 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_timer 25220 2 snd_seq,snd_pcm
snd_page_alloc 10632 2 snd_via82xx,snd_pcm
snd_mpu401 6728 0
snd_mpu401_uart 7680 2 snd_via82xx,snd_mpu401
snd_rawmidi 25504 2 snd_seq_midi,snd_mpu401_uart
snd_seq_device 8716 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
analog 12320 0
snd 55268 14 snd_seq_oss,snd_seq,snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 10208 1 snd
gameport 15496 2 snd_via82xx,analog
parport_pc 35780 1
parport 36296 2 lp,parport_pc
i2c_viapro 8980 0
via_ircc 26900 0
ohci1394 35124 0
ieee1394 299832 2 sbp2,ohci1394
8139cp 22528 0
8139too 26880 0
irda 186940 1 via_ircc
mii 5888 2 8139cp,8139too
crc_ccitt 2304 1 irda
bt878 10552 0
nvidia 4089040 12
tuner 42276 0
floppy 62148 0
pcspkr 2180 0
psmouse 36100 0
rtc 13492 0
serio_raw 7300 0
quickcam 78372 0
usbhid 38752 0
via_agp 9856 1
bttv 164304 1 bt878
video_buf 22148 1 bttv
i2c_algo_bit 9608 1 bttv
v4l2_common 6016 1 bttv
btcx_risc 5128 1 bttv
tveeprom 15248 1 bttv
i2c_core 21904 6 i2c_acpi_ec,i2c_viapro,tuner,bttv,i2c_algo_bit,tveeprom
agpgart 34888 2 nvidia,via_agp
videodev 9856 2 quickcam,bttv
shpchp 45632 0
pci_hotplug 29236 1 shpchp
evdev 9856 4
ext3 135688 3
jbd 58772 1 ext3
ehci_hcd 32520 0
uhci_hcd 33680 0
usbcore 129668 5 quickcam,usbhid,ehci_hcd,uhci_hcd
via82cxxx 9988 0 [permanent]
generic 5124 0
ide_cd 41348 1
cdrom 38560 2 sr_mod,ide_cd
ide_disk 17664 8
ide_generic 1536 0
pdc202xx_new 9600 1
thermal 13576 0
processor 23360 1 thermal
fan 4868 0
capability 5000 0
commoncap 7296 1 capability
vesafb 8476 1
cfbcopyarea 3968 1 vesafb
cfbimgblt 3200 1 vesafb
cfbfillrect 4352 1 vesafb
fbcon 42784 72
tileblit 2816 1 fbcon
font 8320 1 fbcon
bitblit 6272 1 fbcon
softcursor 2304 1 bitblit
More information about the kernel-bugs
mailing list