[Bug 945085] Re: Installer crashed while timezone selection dialog was being displayed.
Ruokoton
945085 at bugs.launchpad.net
Wed Mar 7 06:34:57 UTC 2012
Here are smartctl results when run on Ubuntu 11.10 - they don't seem to
indicate any HW problem:
****
Long selftest:
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.0.0-16-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 500 -
*****
SMART information:
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.0.0-16-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: MCCOE64GEMPP
Serial Number: SE923B5130
Firmware Version: 2.9.03
User Capacity: 60 011 642 880 bytes [60,0 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a
Local Time is: Wed Mar 7 07:57:14 2012 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 15) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 099 099 051 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0007 094 094 001 Pre-fail Always - 4096 (0, 13)
9 Power_On_Hours 0x0033 099 099 000 Pre-fail Always - 500
12 Power_Cycle_Count 0x0033 099 099 000 Pre-fail Always - 176
184 End-to-End_Error 0x0033 099 099 000 Pre-fail Always - 0
187 Reported_Uncorrect 0x0033 100 100 000 Pre-fail Always - 0
188 Command_Timeout 0x0033 099 099 000 Pre-fail Always - 0
190 Airflow_Temperature_Cel 0x0023 045 045 000 Pre-fail Always - 0
195 Hardware_ECC_Recovered 0x001a 200 200 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0033 099 099 000 Pre-fail Always - 0
197 Current_Pending_Sector 0x0012 099 099 000 Old_age Always - 0
198 Offline_Uncorrectable 0x003e 100 100 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x0032 100 100 002 Old_age Always - 0
202 Data_Address_Mark_Errs 0x0032 100 100 002 Old_age Always - 0
232 Available_Reservd_Space 0x0013 094 094 002 Pre-fail Always - 3828
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
*****
I'll run the same tests with the Ubuntu 12.04 installer image later on.
--
You received this bug notification because you are a member of Ubuntu
Foundations Bugs, which is subscribed to ubiquity in Ubuntu.
https://bugs.launchpad.net/bugs/945085
Title:
Installer crashed while timezone selection dialog was being displayed.
Status in “ubiquity” package in Ubuntu:
Invalid
Bug description:
Installer of Ubuntu 12.04 failed at the point of selecting timezone.
ProblemType: Bug
DistroRelease: Ubuntu 12.04
Package: ubiquity 2.9.23
ProcVersionSignature: Ubuntu 3.2.0-17.27-generic-pae 3.2.6
Uname: Linux 3.2.0-17-generic-pae i686
ApportVersion: 1.93-0ubuntu2
Architecture: i386
CasperVersion: 1.305
Date: Fri Mar 2 21:49:57 2012
InstallCmdLine: noprompt cdrom-detect/try-usb=true file=/cdrom/preseed/ubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- maybe-ubiquity
LiveMediaBuild: Ubuntu 12.04 LTS "Precise Pangolin" - Alpha i386 (20120302)
ProcEnviron:
LANGUAGE=
TERM=linux
PATH=(custom, no user)
LANG=en_US.UTF-8
SourcePackage: ubiquity
UpgradeStatus: No upgrade log present (probably fresh install)
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/ubiquity/+bug/945085/+subscriptions
More information about the foundations-bugs
mailing list