h ***************************************** * Load Linux * ***************************************** A Load linux from sd card on LCD B Load linux from sd card on VGA C Load linux from sd card on TV D Load linux from Flash E Load linux through TFTP X Exit select an option : a ***************************************** * Select SD/MMC Host * ***************************************** 1 Select SD/MMC Host 1 2 Select SD/MMC Host 2 X Exit Enter your choice:2 SD/MMC Card Detected# Read 2095104 bytes from file /zImage Launch Linux....Uncompressing Linux....................................................................................................................................... done, booting the kernel... Linux version 2.6.19.2 (root@localhost.localdomain) (gcc version 4.1.1) #1555 Sat May 23 17:53:59 KGST 2009 CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=00053177 Machine: Freescale i.MX27ADS Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists. Total pages: 16256 Kernel command line: console=ttymxc0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs nfsroot=192.168.2.62:/home/savita/ubuntu/fs,nolock mem=64M MXC IRQ initialized WARNING: Can't find valid system rev Assuming last known system_rev=0x20 Actual CLOCK_TICK_RATE is 13300000 Hz WARNING: Can't find valid system rev Assuming last known system_rev=0x20 Console: colour dummy device 80x30 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 60568KB available (3604K code, 636K data, 120K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 IW-PRDL4-SC-01-R2.0-REL2.8-linux2.6.19.2 usb: Host 1 registered usb: Host 2 registered usb: OTG FS Gadget registered Generic PHY: Registered new driver SCSI subsystem initialized CSPI: mxc_spi-0 probed usbcore: registered new device driver usb mc13783 Rev 3.5 FinVer 0 detected Device spi1.0 probed PMIC Character device: successfully loaded PMIC RTC successfully probed PMIC Power successfully probed NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered MX27: Power management module initialized Freescale i.MX27 Dynamic Power Management. NetWinder Floating Point Emulator V0.97 (extended precision) JFFS version 1.0, (C) 1999, 2000 Axis Communications AB JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc. fuse init (API version 7.7) JFS: nTxBlock = 473, nTxLock = 3785 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) modedb fb_find_mode: Trying specified video mode (ignoring refresh rate) 0x0 modedb fb_try_mode: Trying mode VGA_THS8134_SIMULTANEOUS 800x480-16@60 VGA gpio configured LCD :Inside Power ON <6>mxcintuart.0: ttymxc0 at MMIO 0x1000a000 (irq = 20) is a Freescale MXC mxcintuart.1: ttymxc1 at MMIO 0x1000b000 (irq = 19) is a Freescale MXC mxcintuart.2: ttymxc2 at MMIO 0x1000c000 (irq = 18) is a Freescale MXC mxcintuart.4: ttymxc4 at MMIO 0x1001b000 (irq = 49) is a Freescale MXC mxcintuart.5: ttymxc5 at MMIO 0x1001c000 (irq = 48) is a Freescale MXC RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) SMSC LAN83C185: Registered new driver FEC ENET Version 0.2 fec_enet_init::TX & RX Buffer descriptor has been Configured fec_enet_init::Configuring interrupts mii_discover_phy:: going to read phy regsfec: PHY @ 0x0, ID 0x0007c0c3 -- LAN8700 eth0: ethernet aa:33:44:22:11:66 Linux video capture interface: v2.00 st: Version 20050830, fixed bufsize 32768, s/g segs 256 IMX27 Rainbow booted from Flash (bank 0) Probing IMX27 RainBow Boot Flash at physical address 0xc0000000 (16-bit bankwidth) IMX27 RainBow Boot Flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 IMX27 RainBow Boot Flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available cmdlinepart partition parsing not available Using static partitions on IMX27 RainBow Boot Flash Creating 4 MTD partitions on "IMX27 RainBow Boot Flash": 0x00000000-0x00100000 : "Bootloader" 0x00100000-0x00400000 : "Kernel" 0x00400000-0x005c0000 : "Initrd" 0x00600000-0x02000000 : "Filessystem" mice: PS/2 mouse device common for all mice usbmon: debugfs is not available fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 54, io base 0x10024200 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 fsl-ehci fsl-ehci.1: irq 55, io base 0x10024400 fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected drivers/usb/class/audio.c: v1.0.0:USB Audio Class driver Initializing USB Mass Storage driver... USB Mass Storage support registered. Had to override the open usb serial operation with the generic one.Had to override the write usb serial operation with the generic one.Had to override the close usb serial operation with the generic one.Had to override the write_room usb serial operation with the generic one.Had to override the chars_in_buffer usb serial operation with the generic one.Had to override the read_bulk_callback usb serial operation with the generic one.Had to override the write_bulk_callback usb serial operation with the generic one.<6>drivers/usb/serial/usb-serial.c: USB Serial support registered for generic drivers/usb/serial/usb-serial.c: USB Serial Driver core ARC USBOTG Device Controller driver version 1 August 2005 init mmc power on Advanced Linux Sound Architecture Driver Version 1.0.13 (Tue Nov 28 14:07:24 2006 UTC). Control ALSA component registered ALSA device list: #0: MXC Freescale with PMIC TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation Time: mx27_hrt clocksource has been installed. input: mxc_ts as /class/input/input0 mxc input touchscreen loaded drivers/usb/input/hid-core.c: v2.6:USB HID core driver mmc power on eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX. Link down mmc1: host does not support reading read-only switch. assuming write-enable. mmcblk0: mmc1:b368 SDC 488960KiB mmcblk0: p1 p2 Sending DHCP requests .eth0: status: link up, 10MBit Half Duplex, auto-negotiation complete. Link up ., OK IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.2.13 IP-Config: Complete: device=eth0, addr=192.168.2.13, mask=255.255.255.0, gw=192.168.2.254, host=192.168.2.13, domain=iwave.net, nis-domain=(none), bootserver=0.0.0.0, rootserver=192.168.2.62, rootpath= Looking up port of RPC 100003/2 on 192.168.2.62 Looking up port of RPC 100005/1 on 192.168.2.62 VFS: Mounted root (nfs filesystem). Freeing init memory: 120K