Xsane not working

Scott Blair scott.blair at gmail.com
Tue Dec 23 06:08:19 UTC 2014


On 12/23/2014 12:49 AM, NoOp wrote:
> On 12/22/2014 10:41 AM, Scott Blair wrote:
>> On 12/22/2014 01:17 PM, NoOp wrote:
>>> On 12/21/2014 06:50 AM, Scott Blair wrote:
>>>> On 12/21/2014 12:09 AM, NoOp wrote:
>>>>> On 12/20/2014 06:58 PM, Scott Blair wrote:
>>>>>> On 12/20/2014 05:22 PM, NoOp wrote:
>>>>>>> dmesg | tail
>>>>>> http://paste.ubuntu.com/9585507/
>>>>>>
>>>>> Thanks. kodakaio.conf looks stock - I was looking to see if it had been
>>>>> modified for a specific IP address.
>>>>>
>>>>> I don't see Bus 001 Device 011 (device `kodakaio:libusb:001:011') in
>>>>> your lsusb...
>>>>>
>>>>> Turn off the scanner/printer & turn back on, then C&P to pastebin the
>>>>> last 20 or so lines of:
>>>>>
>>>>> $ dmesg
>>>>> $ cat /var/log/syslog
>>>>>
>>>>> and
>>>>>
>>>>> $ scanimage --list-devices
>>>>> $ sudo lsusb
>>>>>
>>>>> Note: you should be seeing something similar to the following (replacing
>>>>> Epson with kodak of course):
>>>>>
>>>>> $ scanimage --list-devices
>>>>> device `epkowa:usb:002:009' is a Epson Stylus SX620FW/Stylus Office
>>>>> BX625FWD/TX620FWD/ME OFFICE 960FWD/WorkForce 630 Series flatbed scanner
>>>>>
>>>>> $ lsusb
>>>>> Bus 002 Device 009: ID 04b8:085d Seiko Epson Corp. PX-603F [ME OFFICE
>>>>> 960FWD Series/Stylus Office BX625FWD/TX620FWD Series]
>>>>>
>>>>>
>>>>>
>>>> dmesg:
>>> <snip>
>>>> [74514.945516] IPv6: wlan0: IPv6 duplicate address
>>>> 2601:3:3000:e17:226:82ff:fe3e:b46b detected!
>>>> [74516.162052] usb 1-3: new high-speed USB device number 14 using ehci-pci
>>>> [74516.308455] usb 1-3: New USB device found, idVendor=040a, idProduct=4043
>>>> [74516.308468] usb 1-3: New USB device strings: Mfr=5, Product=6,
>>>> SerialNumber=7
>>>> [74516.308475] usb 1-3: Product: KODAK ESP 3200 Series AiO
>>>> [74516.308481] usb 1-3: Manufacturer: Eastman Kodak Company
>>>> [74516.308486] usb 1-3: SerialNumber: E219160
>>>> [74516.323309] usblp 1-3:1.1: usblp3: USB Bidirectional printer dev 14
>>>> if 1 alt 0 proto 2 vid 0x040A pid 0x4043
>>>> [74516.325179] usb-storage 1-3:1.2: USB Mass Storage device detected
>>>> [74516.325460] scsi14 : usb-storage 1-3:1.2
>>>> [74517.327634] scsi 14:0:0:0: Direct-Access     KODAK         SD/MMC
>>>> card 1.00 PQ: 0 ANSI: 0
>>>> [74517.328418] sd 14:0:0:0: Attached scsi generic sg9 type 0
>>>> [74517.348059] sd 14:0:0:0: [sdg] Attached SCSI removable disk
>>>> [74517.496609] usblp3: removed
>>>> [74517.505022] usblp 1-3:1.1: usblp3: USB Bidirectional printer dev 14
>>>> if 1 alt 0 proto 2 vid 0x040A pid 0x4043
>>>> [74518.204426] IPv6: wlan0: IPv6 duplicate address
>>>> 2601:3:3000:e17:226:82ff:fe3e:b46b detected!
>>> <snip>
>>>
>>>    IPv6 duplicate address 2601:3:3000:e17:226:82ff:fe3e:b46b detected!
>>>> Dec 21 09:46:50 main kernel: [74617.468186] IPv6: wlan0: IPv6 duplicate address 2601:3:3000:e17:226:82ff:fe3e:b46b detected!
>>>> scott at main:~$
>>>>
>>>>
>>>>
>>>> scanimage --list-devices:
>>>>
>>>> scott at main:~$ scanimage --list-devices
>>>> [bjnp] create_broadcast_socket: bind socket to local address failed -
>>>> Cannot assign requested address
>>>> [bjnp] create_broadcast_socket: bind socket to local address failed -
>>>> Cannot assign requested address
>>>> device `kodakaio:libusb:001:014' is a Kodak KODAK ESP 3200 Series AiO
>>>> flatbed scanner
>>>> scott at main:~$
>>>>
>>>>
>>>>
>>>> sudo lsusb:
>>>>
>>>> scott at main:~$ sudo lsusb
>>>> [sudo] password for scott:
>>>> Bus 007 Device 005: ID 10d5:55a2 Uni Class Technology Co., Ltd 2Port
>>>> KVMSwitcher
>>>> Bus 007 Device 004: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0
>>>> for Bluetooth
>>>> Bus 007 Device 003: ID 046d:c526 Logitech, Inc. Nano Receiver
>>>> Bus 007 Device 002: ID 058f:9254 Alcor Micro Corp. Hub
>>>> Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>> Bus 002 Device 003: ID 058f:6364 Alcor Micro Corp. AU6477 Card Reader
>>>> Controller
>>>> Bus 002 Device 002: ID 1058:070b Western Digital Technologies, Inc.
>>>> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>>>> Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>> Bus 001 Device 012: ID 1058:1130 Western Digital Technologies, Inc.
>>>> Bus 001 Device 014: ID 040a:4043 Kodak Co.
>>>> Bus 001 Device 013: ID 1415:2000 Nam Tai E&E Products Ltd. or OmniVision
>>>> Technologies, Inc. Sony Playstation Eye
>>>> Bus 001 Device 010: ID 04cc:1521 ST-Ericsson USB 2.0 Hub
>>>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>>>> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
>>>> scott at main:~$
>>>>
>>>> Just to let you know, because I didn't mention this earlier, I did
>>>> uninstall and reinstall the printer.
>>>>
>>> Sorry for the delayed reply - I have to go to work.
>>>
>>> It looks like your printer is now detected and working on Bus 001 Device
>>> 014, can you try scanning with xsane from the terminal again & show the
>>> output?
>>>
>>> This is a complete WAG: try installing bjnp to see if that clears the
>>> bjnp port issue:
>>>
>>> $ sudo apt-get install cups-backend-bjnp
>>>
>>> Afterwards, see if there is any change when using 'scanimage
>>> --list-devices'.
>>>
>>>
>>>
>>>
>> Here is the scanimage I forgot in the last email.
>>
>> scott at main:~$ scanimage
>> [bjnp] create_broadcast_socket: bind socket to local address failed -
>> Cannot assign requested address
>> scanimage: output is not a file, exiting
>> scott at main:~$ --list-devices
>>
>>
>
> Other than the "[bjnp] create_broadcast_socket: bind socket to local
> address failed" part, the scanimage command shows that your scanner is
> working, at least code-wise - otherwise it would have responded with:
>
> $ scanimage
> scanimage: no SANE devices found
>
> The "scanimage: output is not a file, exiting" is normal as you didn't
> specify an output. Put something in the scanner and:
>
> $ scanimage > image.pnm
>
> Then providing that you don't get 'scanimage: open of device kodak...
> failed" enter:
>
> $ eog > image.pnm
>
> and let me know if you seen the scan.
>
>
>
>

This is what I get:
scott at main:~$ scanimage > image.pnm
[bjnp] create_broadcast_socket: bind socket to local address failed - 
Cannot assign requested address
scanimage: sane_read: Error during device I/O
scott at main:~$ eog > image.pnm

The image is blank.

-- 

Scott Blair

save on backup time BackUpDevice=null




More information about the ubuntu-users mailing list