Wireless problem

[madunix]

$ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:23:8b:d4:9e:69
          inet addr:192.168.1.100  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::223:8bff:fed4:9e69/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:7468 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7051 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6576790 (6.5 MB)  TX bytes:1522911 (1.5 MB)
          Interrupt:16

eth1      Link encap:Ethernet  HWaddr 00:21:00:ed:b0:31
          inet6 addr: fe80::221:ff:feed:b031/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:930
          TX packets:0 errors:125 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:18

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:972 errors:0 dropped:0 overruns:0 frame:0
          TX packets:972 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:77520 (77.5 KB)  TX bytes:77520 (77.5 KB)

netbook:~$

$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

eth1      IEEE 802.11  Access Point: Not-Associated
          Link Quality:5  Signal level:0  Noise level:191
          Rx invalid nwid:0  invalid crypt:0  invalid misc:0

pan0      no wireless extensions.


dmesg
[ 6973.718248] btusb 3-2:1.0: no reset_resume for driver btusb?
[ 6973.718261] btusb 3-2:1.1: no reset_resume for driver btusb?
[ 6973.968490] PM: resume of drv:usb dev:3-2 complete after 516.170 msecs
[ 6973.968535] PM: resume of devices complete after 2921.457 msecs
[ 6973.969062] PM: resume devices took 2.924 seconds
[ 6973.969144] PM: Finishing wakeup.
[ 6973.969148] Restarting tasks ... done.
[ 6977.669329] tg3 0000:02:00.0: irq 27 for MSI/MSI-X
[ 6977.717817] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6980.441506] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 6980.441515] tg3: eth0: Flow control is on for TX and on for RX.
[ 6980.442088] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6988.004207] eth1: no IPv6 routers present
[ 6990.572046] eth0: no IPv6 routers present

~$ tail -f /var/log/messages
Jun 15 19:23:11 netbook kernel: [ 6973.718248] btusb 3-2:1.0: no
reset_resume for driver btusb?
Jun 15 19:23:11 netbook kernel: [ 6973.718261] btusb 3-2:1.1: no
reset_resume for driver btusb?
Jun 15 19:23:11 netbook kernel: [ 6973.968490] PM: resume of drv:usb
dev:3-2 complete after 516.170 msecs
Jun 15 19:23:11 netbook kernel: [ 6973.968535] PM: resume of devices
complete after 2921.457 msecs
Jun 15 19:23:11 netbook kernel: [ 6973.969062] PM: resume devices took
2.924 seconds
Jun 15 19:23:11 netbook kernel: [ 6973.969148] Restarting tasks ... done.
Jun 15 19:23:15 netbook kernel: [ 6977.717817] ADDRCONF(NETDEV_UP):
eth0: link is not ready
Jun 15 19:23:17 netbook kernel: [ 6980.441506] tg3: eth0: Link is up
at 100 Mbps, full duplex.
Jun 15 19:23:17 netbook kernel: [ 6980.441515] tg3: eth0: Flow control
is on for TX and on for RX.
Jun 15 19:23:17 netbook kernel: [ 6980.442088]
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready




On Tue, Jun 15, 2010 at 7:43 PM, Frank <mailinglists at lavabit.com> wrote:
>
> What's the output of 'ifconfig' and 'iwconfig' ?
>
>
>
>
>
>
> --
> ubuntu-users mailing list
> ubuntu-users at lists.ubuntu.com
> Modify settings or unsubscribe at: https://lists.ubuntu.com/mailman/listinfo/ubuntu-users
>