Intrepid Ibex, Wireless Won't Work on DELL D600
Zaki Akhmad
za at design.paume.itb.ac.id
Wed Feb 11 17:05:26 UTC 2009
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello,
I am using Intrepid Ibex on DELL D600. I have following these
steps[1], on b43 legacy. But my wireless still won't work. Any idea?
Here's my lspci:
# lspci
02:03.0 Network controller: Broadcom Corporation BCM4306 80211b/g
Wireless LAN Controller (rev 02)
# uname -a
2.6-27-7 generic #1 SMP ...
# dmesg
..
[ 1798.441165] b43legacy-phy0 debug: Wireless interface started
[ 1798.448360] b43legacy-phy0 debug: Adding Interface type 3
[ 1798.457851] b43legacy-phy0 debug: Removing Interface type 3
[ 1798.472140] b43legacy-phy0 debug: Wireless interface stopped
[ 1798.473226] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots: 0/64
[ 1798.473893] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots: 0/64
[ 1798.474500] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots: 0/128
[ 1798.480159] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots: 0/128
[ 1798.488136] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots: 0/128
[ 1798.496053] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots: 0/128
[ 1798.504060] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots: 0/128
[ 1798.512246] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots: 0/128
[ 1798.520062] b43legacy-phy0 debug: Radio initialized
[ 1798.520086] b43legacy-phy0 debug: Radio initialized
[ 1798.550438] input: b43legacy-phy0 as /devices/virtual/input/input15
[ 1798.956046] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[ 1799.020784] b43legacy-phy0 debug: Chip initialized
[ 1799.022813] b43legacy-phy0 debug: 30-bit DMA initialized
[ 1799.028147] Registered led device: b43legacy-phy0:tx
[ 1799.028713] Registered led device: b43legacy-phy0:rx
[ 1799.029216] Registered led device: b43legacy-phy0:radio
[ 1799.029273] b43legacy-phy0 debug: Wireless interface started
[ 1799.036388] b43legacy-phy0 debug: Adding Interface type 2
[ 1799.040142] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1801.572345] tg3: eth0: Link is down.
- --
Zaki Akhmad
[1]http://linuxwireless.org/en/users/Drivers/b43#firmwareinstallation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
Comment: Use GnuPG with Firefox : http://getfiregpg.org (Version: 0.7.3)
iEYEARECAAYFAkmTBU0ACgkQI3d58oE7Pt7wSQCfQrv6accqxWy1tHcjCw8E83Mx
ZA0An2AKLBPOwT0uSc9ouZKfm7ZnrXSC
=RjJ9
-----END PGP SIGNATURE-----
More information about the ubuntu-users
mailing list