Hoary : hangs at boot :-(

[Vincent Trouilliez]

> > Please help...
> 
> http://www.ubuntu.com/wiki/DebuggingSystemCrash
> 
> -- 
>  - mdz

Thanks Matt. 

Sadly the system didn't react at all when I pressed "Control + Scroll
lock". I attached /var/log/dmesg. 

The last 4 lines are :
--------
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02ed360(lo)
IPv6 over IPv4 tunneling driver
-------

Does that mean it tries to sync the clock (that's where it hangs) using
IPV6 ? then again, my friend has the exact same modem and ISP, and the
Live CD worked fine on his machine...

Vince
-------------- next part --------------
Linux version 2.6.10-2-386 (buildd at rockhopper) (gcc version 3.3.5 (Debian 1:3.3.5-6ubuntu1)) #1 Wed Jan 19 19:31:57 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001dff0000 (usable)
 BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS)
 BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data)
479MB LOWMEM available.
On node 0 totalpages: 122864
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 118768 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 Nvidia                                ) @ 0x000f6470
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: root=/dev/hdb1 ro quiet splash
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (013c6000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1470.007 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 479652k/491456k available (1427k kernel code, 11156k reserved, 751k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2908.16 BogoMIPS (lpj=1454080)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000020 00000000 00000000
CPU: AMD Athlon(tm) XP 1700+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ACPI: setting ELCR to 0200 (from 0820)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4240k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb360, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041210
    ACPI-1138: *** Error: Method execution failed [\STRC] (Node ddbb5540), AE_AML_BUFFER_LIMIT
    ACPI-1138: *** Error: Method execution failed [\_SB_.PCI0._INI] (Node ddbb05a0), AE_AML_BUFFER_LIMIT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUSB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled by ACPI
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x4000-0x40fe could not be reserved
pnp: 00:01: ioport range 0x40ff-0x40ff has been reserved
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
inotify device minor=63
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
 Strange, kseriod not stopped
 done
ACPI wakeup devices: 
HUB0 USB0 USB1 MMAC MMCI UAR1 
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4240KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (52 C)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE: IDE controller at PCI slot 0000:00:09.0
NFORCE: chipset revision 195
NFORCE: not 100% native mode: will probe irqs later
NFORCE: 0000:00:09.0 (rev c3) UDMA100 controller
    ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST340016A, ATA DISK drive
hdb: ST38410A, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes not supported
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 >
hdb: max request size: 128KiB
hdb: 16841664 sectors (8622 MB) w/512KiB Cache, CHS=16708/16/63, UDMA(33)
hdb: cache flushes not supported
 /dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 >
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8161B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
Adding 381488k swap on /dev/hdb5.  Priority:-1 extents:1
EXT3 FS on hdb1, internal journal
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel at redhat.com
ts: Compaq touchscreen protocol output
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
Real Time Clock Driver v1.12
input: PC Speaker
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce chipset
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: AGP aperture is 64M @ 0xd8000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:02.0: nVidia Corporation nForce USB Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 5, pci mem 0xe0180000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.0: nVidia Corporation nForce USB Controller (#2)
PCI: Setting latency timer of device 0000:00:03.0 to 64
ohci_hcd 0000:00:03.0: irq 11, pci mem 0xe0182000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49205 usecs
intel8x0: clocking to 47395
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xc000, 00:4f:4e:0f:ea:9d, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8139C'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
Linux video capture interface: v1.00
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 11
ACPI: PCI interrupt 0000:01:03.0[A] -> GSI 11 (level, low) -> IRQ 11
bttv0: Bt878 (rev 17) at 0000:01:03.0, irq: 11, latency: 32, mmio: 0xe0000000
bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00fff3ff [init]
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: pinnacle/mt: id=4 info="PAL+SECAM / mono" radio=no
bttv0: using tuner=33
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tda9885/6/7: chip found @ 0x86
tuner: chip found at addr 0xc0 i2c-bus bt878 #0 [sw]
tuner: type set to 33 (MT20xx universal) by bt878 #0 [sw]
tuner: microtune: companycode=4d54 part=04 rev=04
tuner: microtune MT2032 found, OK
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
ACPI: PCI interrupt 0000:01:03.1[A] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02ed360(lo)
IPv6 over IPv4 tunneling driver