Shutdown hangs at: "ACPI_power_off_called".
Bill Stoye
skiffworks at earthlink.net
Thu Oct 7 02:07:14 UTC 2004
On Wed, 2004-10-06 at 18:17 -0700, Matt Zimmerman wrote:
> On Tue, Oct 05, 2004 at 03:27:55PM -0700, Bill Stoye wrote:
>
> > After shutting down fine since the install over two weeks ago, Shutdown
> > hangs at: "ACPI_power_off_called". I've done daily system upgrades since
> > the install, including today; another thing I installed today was
> > 'Zinf', if that could of had an effect. What additional information can
> > I pass on that would be of help?
>
> Complete dmesg output.
bill at skiffworks ~ $ dmesg
RQ 0, using IRQ 20
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 18
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 D1
11 001 01 1 1 0 1 0 1 1 A9
12 001 01 1 1 0 1 0 1 1 C9
13 000 00 1 0 0 0 0 0 0 00
14 001 01 1 1 0 1 0 1 1 C1
15 001 01 1 1 0 1 0 1 1 B1
16 001 01 1 1 0 1 0 1 1 B9
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
.................................... done.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 5
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing
enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 UAR1 LPT1
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4360 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 140k freed
vesafb: probe of vesafb0 failed with error -6
ACPI: Processor [CPU0] (supports C1)
ACPI: Thermal Zone [THRM] (31 C)
ACPI: Fan [FAN] (on)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD800JB-00FMA0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63,
UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
hdc: DVD-ROM BDV316E, ATAPI CD/DVD-ROM drive
hdd: DVD-RW IDE1008, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 500432k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
SCSI subsystem initialized
input: PS2++ Logitech Wheel Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
hdc: ATAPI 40X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
ts: Compaq touchscreen protocol output
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6111 Tue Jul
27 07:55:38 PDT 2004
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm at uk.sistina.com
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
cdrom: open failed.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.8.1-3-686
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 256M @ 0xc0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
tg3.c:v3.8 (July 14, 2004)
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: Tigon3 [partno(BCM95782A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit)
10/100/1000BaseT Ethernet 00:50:2c:09:81:70
eth0: HostTXDS[1] RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0]
WireSpeed[0] TSOcap[1]
ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[21]
MMIO=[e3012000-e30127ff] Max Packet=[2048]
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 22 (level, low) -> IRQ 22
libata version 1.02 loaded.
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via(0000:00:0f.0): routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xA800 ctl 0xAC02 bmdma 0xB800 irq 20
ata2: SATA max UDMA/133 cmd 0xB000 ctl 0xB402 bmdma 0xB808 irq 20
ata1: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e8 86:3c02 87:4023
88:203f
ata1: dev 0 ATA, max UDMA/100, 321672960 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_via
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00502c0000099496]
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
Vendor: ATA Model: HDS722516VLSA80 Rev: V34O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0:
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
uhci_hcd 0000:00:10.0: irq 21, io base 0000c400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
uhci_hcd 0000:00:10.1: irq 21, io base 0000c800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#3)
uhci_hcd 0000:00:10.2: irq 21, io base 0000cc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#4)
usb 1-1: new full speed USB device using address 2
uhci_hcd 0000:00:10.3: irq 21, io base 0000d000
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0
alt 1 proto 2 vid 0x03F0 pid 0x1004
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usb 1-2: new full speed USB device using address 3
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: irq 21, pci mem f8b1b000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
usb 1-2: unable to read config index 0 descriptor/start
usb 1-2: can't read configurations, error -84
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 1-1: USB disconnect, address 2
drivers/usb/class/usblp.c: usblp0: removed
sata_sil version 0.54
ACPI: PCI interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 18
ata3: SATA max UDMA/100 cmd 0xF8B2F080 ctl 0xF8B2F08A bmdma 0xF8B2F000
irq 18
ata4: SATA max UDMA/100 cmd 0xF8B2F0C0 ctl 0xF8B2F0CA bmdma 0xF8B2F008
irq 18
ata3: no device found (phy stat 00000000)
scsi2 : sata_sil
ata4: no device found (phy stat 00000000)
scsi3 : sata_sil
usb 5-6: new high speed USB device using address 4
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
Vendor: Generic Model: STORAGE DEVICE Rev: 0113
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdb at scsi4, channel 0, id 0, lun 0
Vendor: Generic Model: STORAGE DEVICE Rev: 0113
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi4, channel 0, id 0, lun 1
usb 1-1: new full speed USB device using address 5
Vendor: Generic Model: STORAGE DEVICE Rev: 0113
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdd at scsi4, channel 0, id 0, lun 2
Vendor: Generic Model: STORAGE DEVICE Rev: 0113
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sde at scsi4, channel 0, id 0, lun 3
USB Mass Storage device found at 4
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0
alt 1 proto 2 vid 0x03F0 pid 0x1004
usb 1-2: new full speed USB device using address 6
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
tg3: eth0: Link is up at 10 Mbps, half duplex.
tg3: eth0: Flow control is off for TX and off for RX.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e8520(lo)
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
usb 1-2: control timeout on ep0in
eth0: no IPv6 routers present
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Intel ISA PCIC probe: not found.
Device 'i823650' does not have a release() function, it is broken and
must be fixed.
Badness in device_release at drivers/base/core.c:85
[<c019c6fe>] kobject_cleanup+0x98/0x9a
[<f8b652f9>] init_i82365+0x1c0/0x1d6 [i82365]
[<c01312c3>] sys_init_module+0xfa/0x212
[<c0105dfd>] sysenter_past_esp+0x52/0x71
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
Device not ready. Make sure there is a disc in the drive.
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
usb 1-2: control timeout on ep0in
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
bill at skiffworks ~ $
Bill
More information about the ubuntu-users
mailing list