Modem Sagem Fast 800 no breezy
Marcio Sousa
sousa.marcio gmail.com
Quinta-Feira, 24 de Agosto de 2006 - 03:50:35 BST
Viva,
tou a ter alguns problemas na sincronização do modem Sagem Fast 800 da
sapo adsl. Depois de ter instalado as drivers eagle-usb-2.3.2, o modem
fica com ambas as luzes acesas mas parece não se querer sincronizar....
depois de ligar o modem usb
root server:~# eaglediag -msc
Diagnostic (1.23 2005/07/02) driver eagle-usb 20060824033640
# System Information
Linux server 2.6.12-9-386 #1 Mon Oct 10 13:14:36 BST 2005 i686 GNU/Linux
testing/unstable
Linux version 2.6.12-9-386 (buildd rothera) (gcc version 3.4.5 20050809
(prerelease) (Ubuntu 3.4.4-6ubuntu8)) #1 Mon Oct 10 13:14:36 BST 2005
gcc version 3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8.1) used :
3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8.1)
# Dependances
ppp 2.4.3-20050321+2ubuntu1 install ok installed
dhcp-client unknown ok not-installed
No packages found matching dhcpcd.
lrwxrwxrwx 1 root src 36 2006-08-22 23:14 linux ->
/usr/src/linux-headers-2.6.12-9-386/
drwxr-xr-x 18 root root 4096 2006-08-22 23:12 linux-headers-2.6.12-9
drwxr-xr-x 4 root root 4096 2006-08-22 23:13 linux-headers-2.6.12-9-386
Warning : available gcc and the version used to compile the kernel differ
Advice : that's a standard problem on debian, revert to gcc version
used for kernel
# Kernel config : usb modules
eagle_usb 115136 0
ppp_async 10240 0
ppp_generic 25748 1 ppp_async
slhc 6656 1 ppp_generic
crc_ccitt 2176 1 ppp_async
usbhid 30688 0
uhci_hcd 28048 0
usbcore 104188 4 eagle_usb,usbhid,uhci_hcd
# module loaded ? [ OK ]
# modem operational ? [ OK ]
eagle-usb status display
-------------------------------------------------------------
Driver version 2.3.2 Chipset: Eagle3
Vendor ID : 0x1110 Product ID : 0x9031 Rev: 0x200b
USB Bus : 001 USB Device : 005 Dbg mask: 0x0
Ethernet Interface : eth2
MAC: 00:60:4c:f0:36:2c
Tx Rate 128 Rx Rate 512
FEC 0 Margin 45 Atten 3 dB
VID-CPE 0 VID-CO 28 HEC 0
VPI 0 VCI 53 Delin GOOD
Cells Tx 0 Cells Rx 0
Pkts Tx 0 Pkts Rx 0
OAM 0 Bad VPI 0 Bad CRC 0
Oversiz. 0
Modem is operational
# Config vpi/vci/encapsulation/isp : 35 1 (pppoe) PT01
# pppd launched ? [ KO ]
# /etc/resolv.conf should contain the DNS
eth0 Link encap:Ethernet HWaddr 00:05:5D:03:48:BA
inet6 addr: fe80::205:5dff:fe03:48ba/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0xe400
eth1 Link encap:Ethernet HWaddr 00:C0:26:F0:05:1F
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:12 Base address:0x2000
eth2 Link encap:Ethernet HWaddr 00:60:4C:F0:36:2C
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:13300 errors:0 dropped:0 overruns:0 frame:0
TX packets:13300 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1001056 (977.5 KiB) TX bytes:1001056 (977.5 KiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
# ping IP ? [ KO ]
# test DNS resolution ? [ KO ]
##Complete diagnostic saved in
/var/log/eagle-usb/eagle_diag_20060824033640.txt
##Please keep only relevant data and remove personal informations.
root server:~#
A interface eth2 nao fica com ip atribuido e quando faço startadsl o
sistema fica indefinidamente a executar "pppoa -I eth2" sem obter resultado.
Alguém me pode ajudar com isto?
Agradeço a vossa colaboração (ja é a 2 noite a volta disto)...
Marcio.
Mais informações acerca da lista ubuntu-pt