[ubuntu-it] HP DeskJet 710C
An3a
an3a76 a gmail.com
Ven 27 Ott 2006 22:42:31 BST
2006/10/23, gennaro72 a gmail.com <gennaro72 a gmail.com>:
> Devi editare il file pnm2ppa togliendo il # davanti alla riga che contiene
> il valore 710 se non lo trovi allora aggiungi la seguente riga:
>
> version 710
>
> e metti il cancelleto davanti alle altre.
Ciao, scusate il ritardo nella risposta ma non ho sempre accesso alla
macchina con la stampante in questione.
Ho gia' verificato il file in questione, pero' mi sembra tutto a posto
... lo riporto qui sotto, qualcuno ha qualche altro controllo o
suggerimento da darmi?
muchas gracias!
# Sample configuration file
#
# This file will be automatically read upon startup if it is placed in
# /etc/pnm2ppa.conf
#
# uncomment entries by removing "#" to activate them.
#
#-----------set the printer model---------------------------
# The printer model will normally be set by a -v <model> command
# line argument. Otherwise, if not set in the configuration file
# it defaults to the 710/720 series. Remove/comment out the line
# "version 0" below to get the default choice.
#
# If there is more than one "version" entry activated, the last one
# will be used. The printer version can also be set with the command line
# option e.g., "-v 720".
version 710
#version 720 # 710, 712, 722 also acceptable
#version 820
#version 1000
#--------control system log messages from pnm2ppa-------------------
# pnm2ppa issues progress and error messages to the system log (syslog).
# For security reasons, no input from the user is ever sent to the syslog.
# The setting "silent 1" suppresses messages to the syslog. The
# setting "verbose 1" sends messages to the standard error stream (stderr)
# in addition to the syslog. (Note: if pnm2ppa was compiled with the
# -D__NO_SYSLOG__ option (e.g., for BeOS), syslog messages are
# diverted to stderr; use "silent 1" to suppress them.)
#silent 1
#verbose 1
# (NEW FEATURE:)
# standard informational messages ( when a job starts, when each page
# prints, job finished, etc.) will not be recorded in the System Log,
# unless explicitly activated here with the "log_info 1" keyword.
# (i.e., "log_info 0" is the default.)
# (Informational messages will still always be sent to stderr in "verbose"
# mode, even if log_info is not set.)
log_info 1 # <= COMMENT THIS OUT TO GET THE NEW DEFAULT BEHAVIOR!
# Note: the "silent 1" and "log_info" keywords are only accepted from the
# system configuration file (/etc/pnm2ppa.conf), and not from configuration
# files specified by users with the pnm2ppa option "-f".
#---------set the margins of the printed page-------------------
# Margins: these are distances from the edges of the paper in
# "dots" ( 600 dots = 1 inch = 2.54 cm).
# Nothing outside these margins will be printed.
# Default values are give below; uncomment and change, if necessary.
# (Older versions of pnm2ppa required larger left and right margins to avoid
# printer failure with "flashing lights", but this problem is believed to
# be solved)
#topmargin 10
#bottommargin 150
#leftmargin 10
#rightmargin 10
#----------center the printer output on the paper-------------------
# Offsets: these are adjustments for centering the print correctly on the
# paper. Units are dots (1/600 inch). Add a positive number of dots to
# xoff to move the printed image to the right, relative to the paper.
# add to yoff to move it down. The helper program calibrate_ppa prints
# a test page to check the offsets (see CALIBRATON.txt):
# usage: "calibrate_ppa --center | pnm2ppa --bw - - | lpr -l
# Default values are:
#xoffset 160
#yoffset 50
#------------align the black and color ink cartridges--------
# Color Offsets: these control alignment between the black ink
# and color ink print cartridges. This changes a little whenever you
# replace an ink cartridge, so the default values are just approximate.
#
# Use "calibrate_ppa --align | pnm2ppa --fd - - | lpr -l "
# to print a test page to help you adjust the color offsets.
#
# The first line checks horizontal alignment ColOffsX,:
# The second line checks vertical alignment ColOffsY,:
# The alignment is correct if alignment patterns "0" is best.
# If a diffent alignment pattern is best, add or subtract the + or
# - value shown below it to ColOffsX or ColOffSy.
#
# See CALIBRATION.txt for more details.
# Use "calibrate_ppa --test | pnm2ppa --fd - - | lpr -l " to check your
# new settings.
#ColOffsX 0
#ColOffsY 0
#---------------"shearing" corrections-------------------------------------
# shearing correction (for bidirectional printing modes)
# if there is a horizontal offset between right-to-left and left-to-right
# sweeps of the print head, adjust these in units of 1"/600 (1 dot).
# There are separate corrections colorshear and blackshear for the
# color and black print heads. The third and fourth lines of the
# alignment test page (see above) tests these.
# The setting is correct when alignments "0" are correct.
# The (positive or negative) number shown under the best-aligned shearing
# alignment pattern tells you how much to change the colorshar or blackshear
# value by. (For, example, if you print the calibration page with
# "colorshear 0" (the default value) and the best pattern is labelled "-2",
# uncomment the "colorshear" value below and set it equal to -2.)
#colorshear 0
#blackshear 0
#-------------blackness control-----------------------------
# this controls the density of black ink used.
# valid blackness choices are 1 2 3 4; controls the
# density of black ink used: 1 (least ink), 2 (default), 4 (most).
# 0 = no black ink. This affects black ink bordered by whitespace
# only (e.g. text, but not black in color images)
#blackness 2
#------------Color correct curve Gamma parameters-------------------------
# Gamma color correction values for Red, Green and Blue:
# (Note: a more effective method of color correction is to use
# a calibration file /etc/pnm2ppa.gamma, in which case these
# Gamma values will not be used. See COLOR.html or COLOR.txt)
# The pnm2ppa option --noGamma suppresses color correction.
# The standard Gamma enhancement curve is
# gEnh(i) = (int) ( pow ( (double) i / 256, Gamma ) * 256 )
# (i.e., 256 times ( i*(1.0/256)) to the power Gamma ),
# where (int) i is the ppm color intensity, in the range 0 - 255.
# positive values of Gamma enhance (increase the intensity of)
# the corresponding color. Gamma = 1.0 corresponds to no
# color correction, gEnh[i] = i.
# You can specify Gamma values as a decimal number for each primary color
#GammaR 1.0 # red enhancement
#GammaG 1.0 # green enhancement
#GammaB 1.0 # blue enhancement
# For use with the printed output of "pnm2ppa -g ",
# you can also specify Gamma values using the integer GammaIdx,
# which gives Gamma = 1.0 - 0.033 * GammaIdx :
#RedGammaIdx 0
#GreenGammaIdx 0
#BlueGammaIdx 0
# Default papersize (only used for printing the color calibration
# test page with pnm2ppa -g).
# Valid choices are: a4, letter, legal:
#papersize letter # this is the default
#papersize legal
#papersize a4
#-----------suppress bidirectional printing---------------------
# by default the printing sweeps are now bidirectional (unimode 0);
# to make unidirectional printing (left-to-right) the default behavior,
# (unimode 1) uncomment the next line . (The command line options --uni
# and --bi override the default behavior). You might wish to print
# unidirectionally to avoid shearing effects in high-quality
# color images, for example)
#unimode 1
#------------switch off (color) data compression------------------
# Previously, data compression of color data sent to the printer
# was not enabled. It is now enabled by default, but has only
# been tested on HP71x/72xC models. Uncomment and set "compression 0"
# to disable color data compression if necessary.
#compression 1
#=====================================================================
# the following are switches for debugging purposes only:
# set their values to 0 to switch off the corresponding ink type:
#black_ink 1
#color_ink 1
#cyan_ink 1
#magenta_ink 1
#yellow_ink 1
--
An3a
"Una persona non dovrebbe mai lasciare tracce cosi' profonde che il
vento non le possa cancellare."
Piedineri, tribu' Indiani d'America
Greenpeace it :: www.greenpeace.it
Greenpeace it - G.L. Torino :: www.greenpeace.it/local/torino
Mountain Wilderness it :: www.mountwild.it
Linux User #405738
Maggiori informazioni sulla lista
ubuntu-it