[ubuntu-it] Dopo aggiornamento non va pių wifi
pacmo a tiscalinet.it
pacmo a tiscalinet.it
Mar 19 Dic 2006 10:43:41 GMT
Bruno Aleci ha scritto:
> 2006/12/19, pacmo a tiscalinet.it <pacmo a tiscalinet.it>:
>> 3crusb10075 č il dispositvo wifi usb che usavo sotto edge.
>> Ho aggiornato ad edgy e subito mi ha dato 200 righe di questo errore :
>> firmware_helper ..... main error loading
>> '/lib/firmware/bcm43xx_microcodes.fw for device ....with driver 'bcm43xx'
>> Ho copiato i driver bcm43xx da 2.6.15 a 2.6.17 e l'errore non č pių
>> comparso ... in compenso.
>>
>>
>> lspci
>> Network controller: Broadcom Corporation BCM4318 [AirForce One 54g]
>> 802.11g Wireless LAN Controller (rev 02)
>> 08:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
>> Controller (rev c0)
>> dmesg
>> usb 3-1: new high speed USB device using ehci_hcd and address 3
>> [17179715.784000] usb 3-1: configuration #1 chosen from 1 choice
>> [17179716.136000] zd1211rw 3-1:1.0: firmware version 4605
>> [17179716.180000] zd1211rw 3-1:1.0: zd1211 chip 6891:a727 v4330 high
>> 00-16-e0 RF2959_RF pa0 g--
>> [17179716.180000] zd1211rw 3-1:1.0: eth2
>> [17179716.180000] usbcore: registered new driver zd1211rw
>> [17179716.328000] ADDRCONF(NETDEV_UP): eth2: link is not ready
>>
>> iwconfig
>> lo no wireless extensions.
>>
>> eth1 IEEE 802.11b/g ESSID:off/any Nickname:"Broadcom 4318"
>> Mode:Managed Frequency=2.484 GHz Access Point: Invalid
>> Bit Rate=1 Mb/s Tx-Power=18 dBm
>> RTS thr:off Fragment thr:off
>> Encryption key:off
>> Link Quality:0 Signal level:0 Noise level:0
>> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
>> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>>
>> eth0 no wireless extensions.
>>
>> sit0 no wireless extensions.
>>
>> eth2 802.11g zd1211 ESSID:off/any
>> Mode:Managed Frequency:2.462 GHz Access Point: Invalid
>> Bit Rate=1 Mb/s
>> Encryption key:off
>> Link Quality=86/100 Signal level=87/100
>> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
>> Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>>
>> /etc/network/interfaces era cosė
>>
>> auto wlan0
>> iface wlan0 inet static
>> broadcast 10.33.0.0
>> address 10.33.0.87
>> netmask 255.255.255.0
>> gateway 10.33.0.200
>> up /sbin/iwconfig wlan0 essid pac && /sbin/iwconfig wlan0 key 123456789
>>
>> Le spie dell'aggeggio sono spente. A volte trova la rete per un attimo
>> con kwifimanager
>> Come posso fare
>> ciao
>> pac
>>
>>
>>
>> --
>> ubuntu-it mailing list
>> ubuntu-it a lists.ubuntu.com
>> https://lists.ubuntu.com/mailman/listinfo/ubuntu-it
>>
>
> se vedi iwconfig non č pių wlan0 ma č eth2 o eth1
Infatti con iwlist scanning vede l'AP ed ho configurato eth2 ma non
cambia nulla, rimane sempre spento
Maggiori informazioni sulla lista
ubuntu-it