[ubuntu-in] BSNL Huawei CDMA problem

[Ramnarayan.K]

Hi Ninad,

following your suggestions

On Mon, Jun 15, 2009 at 5:43 PM, Ninad Pundalik <ninadsp16289 at gmail.com>wrote:

> Kindly check the mail I had sent in response to your earlier mail.
> This is a problem with wvdial and not the kernel, if you are unable to
> connect to the internet.  I too had similar problems with a different
> dialer.  I used ppoeconfig to set it up, and successfully connect to
> the net.  The directions are posted at my blog, on this post.
>
> http://ninadpundalik.co.cc/blog/2009/05/lg-lxu800-dialer-on-ubuntu-jaunty/
>
> Please revert with your progress, and any problems that you have.
>
>
I have tried to set it up under pppoeconfig and it still does not work.

This is the present situation
$ dmesg
[ 2463.820056] usb 2-2: new full speed USB device using uhci_hcd and address
6
[ 2464.011217] usb 2-2: configuration #1 chosen from 1 choice
[ 2464.017144] ti_usb_3410_5052 2-2:1.0: TI USB 3410 1 port adapter
converter detected
[ 2464.017151] usb 2-2: firmware: requesting ti_usb-v0451-p3410.fw
[ 2464.028810] usb 2-2: firmware: requesting ti_3410.fw
[ 2464.612056] usb 2-2: reset full speed USB device using uhci_hcd and
address 6
[ 2464.755125] usb 2-2: device firmware changed
[ 2464.755151] ti_usb_3410_5052: probe of 2-2:1.0 failed with error -5
[ 2464.756857] usb 2-2: USB disconnect, address 6
[ 2464.924057] usb 2-2: new full speed USB device using uhci_hcd and address
7
[ 2465.143219] usb 2-2: configuration #1 chosen from 2 choices
[ 2465.145169] ti_usb_3410_5052 2-2:1.0: TI USB 3410 1 port adapter
converter detected
[ 2465.145180] ti_usb_3410_5052: probe of 2-2:1.0 failed with error -5
[ 2465.147201] ti_usb_3410_5052 2-2:2.0: TI USB 3410 1 port adapter
converter detected
[ 2465.147273] usb 2-2: TI USB 3410 1 port adapter converter now attached to
ttyUSB0

$ wvdial 93
--> WvDial: Internet dialer version 1.60
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT#777
--> Waiting for carrier.
ATDT#777
CONNECT
--> Carrier detected.  Starting PPP immediately.
--> Unable to run /usr/sbin/pppd.
--> Check permissions, or specify a "PPPD Path" option in wvdial.conf.
^CCaught signal 2:  Attempting to exit gracefully...
--> Disconnecting at Wed Jul  1 22:03:21 2009
ram at ram-laptop:~$ sudo wvdial 93
[sudo] password for ram:
--> WvDial: Internet dialer version 1.60
--> Cannot open /dev/ttyUSB0: Input/output error
--> Cannot open /dev/ttyUSB0: Input/output error
--> Cannot open /dev/ttyUSB0: Input/output error

Note from wvdial.conf
[Modem0]
Modem = /dev/ttyUSB0
Baud = 115200
SetVolume = 0
Dial Command = ATDT
Init1 = ATZ
FlowControl = Hardware (CRTSCTS)
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
# Init3 = at+crm=1;+cmux=1;+cps=33;+cta=0
Modem Type = Analog Modem
Baud = 115200
New PPPD = yes
Modem = /dev/ttyUSB0
Idle Seconds = 90
Auto Reconnect = off

[Dialer 93]
Modem = /dev/ttyUSB0
Baud = 230400
Phone = #777
Init1 = ATZ
Stupid Mode = 1
Dial Command = ATDT
Username = 5961211393
Password = 5961211393
# below line error in spelling crtcts which should be crtscts
# PPPD Options = crtcts multilink usepeerdns lock defaultroute
# PPPD Options = crtscts multilink usepeerdns lock defaultroute
Inherits = Modem0

**
gnome ppp
--> Ignoring malformed input line: ";Do NOT edit this file by hand!"
--> WvDial: Internet dialer version 1.60
--> Cannot open /dev/ttyUSB0: Input/output error
--> Cannot open /dev/ttyUSB0: Input/output error
--> Cannot open /dev/ttyUSB0: Input/output error

kppp
unable to open modem

gpppon
gives no response  and does not show any connection

***
So what next would be grateful for ideas

ram
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://lists.ubuntu.com/archives/ubuntu-in/attachments/20090701/49270a56/attachment.htm