[Ubuntu-BR] [Dúvida]Sincronismo entre dispositivos portáteis e ubuntu

Renato Resende Batista zenatuz em gmail.com
Terça Novembro 6 12:07:05 UTC 2007


Olá, fiz como o sugerido, no ls -all /dev/pilot é informado que não
existe.

já no dmesg informa o seguinte:

[    0.000000] Linux version 2.6.22-14-generic (buildd em palmer) (gcc
version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun
Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[    0.000000]  BIOS-e820: 000000000009dc00 - 00000000000a0000
(reserved)
[    0.000000]  BIOS-e820: 00000000000d2000 - 0000000000100000
(reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000004df00000 (usable)
[    0.000000]  BIOS-e820: 000000004df00000 - 000000004df17000 (ACPI
data)
[    0.000000]  BIOS-e820: 000000004df17000 - 000000004df80000 (ACPI
NVS)
[    0.000000]  BIOS-e820: 000000004df80000 - 0000000050000000
(reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000
(reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000
(reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000
(reserved)
[    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000
(reserved)
[    0.000000] 351MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at 000f89c0
[    0.000000] Entering add_active_range(0, 0, 319232) 0 entries of 256
used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   319232
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   319232
[    0.000000] On node 0 totalpages: 319232
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 702 pages used for memmap
[    0.000000]   HighMem zone: 89154 pages, LIFO batch:15
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP signature @ 0xC00F8990 checksum 0
[    0.000000] ACPI: RSDP 000F8990, 0014 (r0 HP    )
[    0.000000] ACPI: RSDT 4DF0FC35, 0038 (r1 HP       RSDT    6040000
LTP        0)
[    0.000000] ACPI: FACP 4DF16DEE, 0074 (r1 HP     MCP51M    6040000
PTL_    F4240)
[    0.000000] ACPI: DSDT 4DF0FC6D, 7181 (r1 HP       MCP51M  6040000
MSFT  100000E)
[    0.000000] ACPI: FACS 4DF17FC0, 0040
[    0.000000] ACPI: SSDT 4DF16E62, 00F4 (r1 HP     POWERNOW  6040000
LTP        1)
[    0.000000] ACPI: MCFG 4DF16F56, 003C (r1 HP       MCFG    6040000
LTP        0)
[    0.000000] ACPI: APIC 4DF16F92, 0046 (r1 HP          APIC    6040000
LTP        0)
[    0.000000] ACPI: BOOT 4DF16FD8, 0028 (r1     HP $SBFTBL$  6040000
LTP        1)
[    0.000000] Nvidia board detected. Ignoring ACPI timer override.
[    0.000000] If you got timer trouble try acpi_use_timer_override
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 15:12 APIC version 16
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI
0-23
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 60000000 (gap:
50000000:90000000)
[    0.000000] Built 1 zonelists.  Total pages: 316738
[    0.000000] Kernel command line:
root=UUID=028bdb80-bd23-4f99-8f08-57c9d43ef124 ro quiet splash vga=795
[    0.000000] mapped APIC to ffffd000 (fee00000)
[    0.000000] mapped IOAPIC to ffffc000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 1808.376 MHz processor.
[   35.463058] spurious 8259A interrupt: IRQ7.
[   35.467748] Console: colour VGA+ 80x34
[   35.468131] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[   35.468844] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[   35.502602] Memory: 1254336k/1276928k available (2015k kernel code,
21708k reserved, 916k data, 364k init, 359424k highmem)
[   35.502613] virtual kernel memory layout:
[   35.502614]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[   35.502615]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   35.502617]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   35.502618]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   35.502619]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[   35.502621]       .data : 0xc02f7d26 - 0xc03dce84   ( 916 kB)
[   35.502622]       .text : 0xc0100000 - 0xc02f7d26   (2015 kB)
[   35.502625] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[   35.502666] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4,
CPUs=1, Nodes=1
[   35.582654] Calibrating delay using timer specific routine.. 3619.85
BogoMIPS (lpj=7239718)
[   35.582682] Security Framework v1.0.0 initialized
[   35.582689] SELinux:  Disabled at boot.
[   35.582702] Mount-cache hash table entries: 512
[   35.582830] CPU: After generic identify, caps: 078bfbff ebd3fbff
00000000 00000000 00002001 00000000 00000019
[   35.582839] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[   35.582842] CPU: L2 Cache: 256K (64 bytes/line)
[   35.582845] CPU: After all inits, caps: 078bfbff ebd3fbff 00000000
00000410 00002001 00000000 00000019
[   35.582855] Compat vDSO mapped to ffffe000.
[   35.582866] Checking 'hlt' instruction... OK.
[   35.598786] SMP alternatives: switching to UP code
[   35.598989] Freeing SMP alternatives: 11k freed
[   35.599285] Early unpacking initramfs... done
[   35.917766] ACPI: Core revision 20070126
[   35.917853] ACPI: Looking for DSDT in initramfs... error,
file /DSDT.aml not found.
[   35.923501] CPU0: AMD Mobile AMD Sempron(tm) Processor 3400+ stepping
02
[   35.923522] Total of 1 processors activated (3619.85 BogoMIPS).
[   35.923824] ENABLING IO-APIC IRQs
[   35.924075] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[   36.070479] Brought up 1 CPUs
[   36.070609] Booting paravirtualized kernel on bare hardware
[   36.070694] Time:  9:57:45  Date: 10/06/107
[   36.070716] NET: Registered protocol family 16
[   36.070798] EISA bus registered
[   36.070813] ACPI: bus type pci registered
[   36.086369] PCI: BIOS BUG #81[49435000] found
[   36.086414] PCI: Using configuration type 1
[   36.086416] Setting up standard PCI resources
[   36.088024] ACPI: EC: Look up EC in DSDT
[   36.088334] ACPI: EC: GPE=0x10, ports=0x66, 0x62
[   36.089723] ACPI: Interpreter enabled
[   36.089726] ACPI: (supports S0 S3 S4 S5)
[   36.089739] ACPI: Using IOAPIC for interrupt routing
[   36.095546] ACPI: EC: GPE=0x10, ports=0x66, 0x62
[   36.095608] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   36.095616] PCI: Probing PCI hardware (bus 00)
[   36.096568] PCI: Transparent bridge - 0000:00:10.0
[   36.096598] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   36.096688] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[   36.096713] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[   36.096741] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[   36.127867] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 10 11 14 15)
*0, disabled.
[   36.128048] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
[   36.128225] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 11 14 15)
*0, disabled.
[   36.128402] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15)
*0, disabled.
[   36.128582] ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20 21
22 23) *0, disabled.
[   36.128760] ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20 21
22 23) *0, disabled.
[   36.128943] ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20 21
22 23) *11
[   36.129118] ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21
22 23) *0, disabled.
[   36.129294] ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21
22 23) *10
[   36.129470] ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20 21
22 23) *10
[   36.129645] ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21
22 23) *11
[   36.129828] ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21
22 23) *7
[   36.130004] ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21
22 23) *10
[   36.130180] ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21
22 23) *0, disabled.
[   36.130356] ACPI: PCI Interrupt Link [LACI] (IRQs 16 17 18 19 20 21
22 23) *0, disabled.
[   36.130540] ACPI: PCI Interrupt Link [LMCI] (IRQs 16 17 18 19 20 21
22 23) *0, disabled.
[   36.130717] ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21
22 23) *0, disabled.
[   36.130902] ACPI: PCI Interrupt Link [LTID] (IRQs 16 17 18 19 20 21
22 23) *5
[   36.131084] ACPI: PCI Interrupt Link [LSI1] (IRQs 16 17 18 19 20 21
22 23) *10
[   36.131182] Linux Plug and Play Support v0.97 (c) Adam Belay
[   36.131193] pnp: PnP ACPI init
[   36.131207] ACPI: bus type pnp registered
[   36.133144] pnp: PnP ACPI: found 11 devices
[   36.133147] ACPI: ACPI bus type pnp unregistered
[   36.133150] PnPBIOS: Disabled by ACPI PNP
[   36.133199] PCI: Using ACPI for IRQ routing
[   36.133203] PCI: If a device doesn't work, try "pci=routeirq".  If it
helps, post a report
[   36.133289] NET: Registered protocol family 8
[   36.133291] NET: Registered protocol family 20
[   36.133357] pnp: 00:00: iomem range 0xffc00000-0xffffffff could not
be reserved
[   36.133361] pnp: 00:00: iomem range 0xfec00000-0xfec00fff could not
be reserved
[   36.133364] pnp: 00:00: iomem range 0xfee00000-0xfeefffff could not
be reserved
[   36.133367] pnp: 00:00: iomem range 0x0-0x0 could not be reserved
[   36.133373] pnp: 00:02: iomem range 0xe0000000-0xefffffff could not
be reserved
[   36.133378] pnp: 00:03: ioport range 0x1000-0x107f has been reserved
[   36.133382] pnp: 00:03: ioport range 0x1080-0x10ff has been reserved
[   36.133384] pnp: 00:03: ioport range 0x1400-0x147f has been reserved
[   36.133387] pnp: 00:03: ioport range 0x1480-0x14ff has been reserved
[   36.133390] pnp: 00:03: ioport range 0x1800-0x187f has been reserved
[   36.133393] pnp: 00:03: ioport range 0x1880-0x18ff has been reserved
[   36.133396] pnp: 00:03: ioport range 0x2000-0x203f has been reserved
[   36.134420] Time: tsc clocksource has been installed.
[   36.163654] PCI: Bridge: 0000:00:02.0
[   36.163656]   IO window: 4000-4fff
[   36.163660]   MEM window: b3000000-b31fffff
[   36.163663]   PREFETCH window: d0000000-d01fffff
[   36.163666] PCI: Bridge: 0000:00:03.0
[   36.163667]   IO window: disabled.
[   36.163670]   MEM window: b3200000-b33fffff
[   36.163672]   PREFETCH window: disabled.
[   36.163675] PCI: Bridge: 0000:00:10.0
[   36.163677]   IO window: disabled.
[   36.163680]   MEM window: disabled.
[   36.163682]   PREFETCH window: disabled.
[   36.163694] PCI: Setting latency timer of device 0000:00:02.0 to 64
[   36.163701] PCI: Setting latency timer of device 0000:00:03.0 to 64
[   36.163708] PCI: Setting latency timer of device 0000:00:10.0 to 64
[   36.163721] NET: Registered protocol family 2
[   36.194425] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[   36.194541] TCP established hash table entries: 131072 (order: 8,
1572864 bytes)
[   36.195886] TCP bind hash table entries: 65536 (order: 7, 524288
bytes)
[   36.196394] TCP: Hash tables configured (established 131072 bind
65536)
[   36.196397] TCP reno registered
[   36.206504] checking if image is initramfs... it is
[   36.666180] Switched to high resolution mode on CPU 0
[   36.829300] Freeing initrd memory: 7043k freed
[   36.829401] Simple Boot Flag at 0x36 set to 0x1
[   36.829668] audit: initializing netlink socket (disabled)
[   36.829680] audit(1194343065.032:1): initialized
[   36.829739] highmem bounce pool size: 64 pages
[   36.831313] VFS: Disk quotas dquot_6.5.1
[   36.831359] Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[   36.831446] io scheduler noop registered
[   36.831449] io scheduler anticipatory registered
[   36.831450] io scheduler deadline registered
[   36.831464] io scheduler cfq registered (default)
[   36.831483] Boot video device is 0000:00:05.0
[   37.046062] PCI: Setting latency timer of device 0000:00:02.0 to 64
[   37.046083] assign_interrupt_mode Found MSI capability
[   37.046086] Allocate Port Service[0000:00:02.0:pcie00]
[   37.046148] PCI: Setting latency timer of device 0000:00:03.0 to 64
[   37.046170] assign_interrupt_mode Found MSI capability
[   37.046172] Allocate Port Service[0000:00:03.0:pcie00]
[   37.046275] isapnp: Scanning for PnP cards...
[   37.399127] isapnp: No Plug & Play device found
[   37.424754] Real Time Clock Driver v1.12ac
[   37.424839] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[   37.426002] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 blocksize
[   37.426186] input: Macintosh mouse button emulation
as /class/input/input0
[   37.426249] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at
0x60,0x64 irq 1,12
[   37.442708] serio: i8042 KBD port at 0x60,0x64 irq 1
[   37.442714] serio: i8042 AUX port at 0x60,0x64 irq 12
[   37.442870] mice: PS/2 mouse device common for all mice
[   37.443801] EISA: Probing bus 0 at eisa.0
[   37.443808] Cannot allocate resource for EISA slot 1
[   37.443811] Cannot allocate resource for EISA slot 2
[   37.443813] Cannot allocate resource for EISA slot 3
[   37.443815] Cannot allocate resource for EISA slot 4
[   37.443828] EISA: Detected 0 cards.
[   37.443917] TCP cubic registered
[   37.443928] NET: Registered protocol family 1
[   37.443948] Using IPI No-Shortcut mode
[   37.444118]   Magic number: 15:874:979
[   37.444133]   hash matches device ttyc6
[   37.444512] Freeing unused kernel memory: 364k freed
[   37.481800] input: AT Translated Set 2 keyboard
as /class/input/input1
[   38.696266] fuse init (API version 7.8)
[   38.703057] Capability LSM initialized
[   38.711554] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   38.711569] ACPI Exception (processor_core-0783): AE_NOT_FOUND,
Processor Device is not present [20070126]
[   38.713047] ACPI: Thermal Zone [THRM] (57 C)
[   39.500034] usbcore: registered new interface driver usbfs
[   39.500059] usbcore: registered new interface driver hub
[   39.500078] usbcore: registered new device driver usb
[   39.501392] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 23
[   39.501405] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUS2] -> GSI
23 (level, high) -> IRQ 16
[   39.501416] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[   39.501420] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[   39.501574] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned
bus number 1
[   39.501606] ehci_hcd 0000:00:0b.1: debug port 1
[   39.501611] PCI: cache line size of 64 is not supported by device
0000:00:0b.1
[   39.501623] ehci_hcd 0000:00:0b.1: irq 16, io mem 0xb0005000
[   39.501632] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[   39.501730] usb usb1: configuration #1 chosen from 1 choice
[   39.501759] hub 1-0:1.0: USB hub found
[   39.501766] hub 1-0:1.0: 8 ports detected
[   39.513186] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   39.513191] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[   39.535524] SCSI subsystem initialized
[   39.540092] libata version 2.21 loaded.
[   39.555191] forcedeth.c: Reverse Engineered nForce ethernet driver.
Version 0.60.
[   39.601187] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
(OHCI) Driver
[   39.661067] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
[   39.661080] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI
22 (level, high) -> IRQ 17
[   39.661087] PCI: Setting latency timer of device 0000:00:14.0 to 64
[   39.661095] forcedeth: using HIGHDMA
[    4.224000] Marking TSC unstable due to: possible TSC halt in C2.
[    4.228000] Time: acpi_pm clocksource has been installed.
[    4.580000] eth0: forcedeth.c: subsystem: 0103c:30b7 bound to
0000:00:14.0
[    4.580000] sata_nv 0000:00:0e.0: version 3.4
[    4.580000] PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
[    4.580000] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 21
[    4.580000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI
21 (level, high) -> IRQ 18
[    4.580000] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[    4.580000] scsi0 : sata_nv
[    4.580000] scsi1 : sata_nv
[    4.580000] ata1: SATA max UDMA/133 cmd 0x000130c0 ctl 0x000130b6
bmdma 0x00013090 irq 18
[    4.580000] ata2: SATA max UDMA/133 cmd 0x000130b8 ctl 0x000130b2
bmdma 0x00013098 irq 18
[    5.048000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    5.072000] ata1.00: ATA-7: SAMSUNG HM120JI, YF100-15, max UDMA7
[    5.072000] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth
0/32)
[    5.088000] ata1.00: configured for UDMA/133
[    5.400000] ata2: SATA link down (SStatus 0 SControl 300)
[    5.408000] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HM120JI
YF10 PQ: 0 ANSI: 5
[    5.412000] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
[    5.412000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI
20 (level, high) -> IRQ 19
[    5.412000] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[    5.412000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[    5.412000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned
bus number 2
[    5.412000] ohci_hcd 0000:00:0b.0: irq 19, io mem 0xb0004000
[    5.424000] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors
(120034 MB)
[    5.424000] sd 0:0:0:0: [sda] Write Protect is off
[    5.424000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.424000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[    5.424000] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors
(120034 MB)
[    5.424000] sd 0:0:0:0: [sda] Write Protect is off
[    5.424000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.424000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[    5.424000]  sda:<6>usb usb2: configuration #1 chosen from 1 choice
[    5.468000] hub 2-0:1.0: USB hub found
[    5.468000] hub 2-0:1.0: 8 ports detected
[    5.572000] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[    5.572000] NFORCE-MCP51: chipset revision 241
[    5.572000] NFORCE-MCP51: not 100% native mode: will probe irqs later
[    5.572000] NFORCE-MCP51: BIOS didn't set cable bits correctly.
Enabling workaround.
[    5.572000] NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
[    5.572000]     ide0: BM-DMA at 0x3080-0x3087, BIOS settings:
hda:DMA, hdb:pio
[    5.572000] Probing IDE interface ide0...
[    5.876000] usb 2-6: new low speed USB device using ohci_hcd and
address 2
[    5.900000]  sda1 sda2 < sda5 sda6 sda7 > sda3
[    5.956000] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.960000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    6.084000] usb 2-6: configuration #1 chosen from 1 choice
[    6.100000] usbcore: registered new interface driver hiddev
[    6.108000] input: USB Optical Mouse as /class/input/input2
[    6.108000] input: USB HID v1.10 Mouse [USB Optical Mouse] on
usb-0000:00:0b.0-6
[    6.108000] usbcore: registered new interface driver usbhid
[
6.108000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[    6.308000] hda: TSSTcorpCDW/DVD TS-L462D, ATAPI CD/DVD-ROM drive
[    6.432000] Attempting manual resume
[    6.432000] swsusp: Resume From Partition 8:7
[    6.432000] PM: Checking swsusp image.
[    6.432000] PM: Resume from disk failed.
[    6.448000] EXT3-fs: INFO: recovery required on readonly filesystem.
[    6.448000] EXT3-fs: write access will be enabled during recovery.
[    6.980000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    7.020000] hda: ATAPI 24X DVD-ROM CD-R/RW drive, 1536kB Cache, DMA
[    7.020000] Uniform CD-ROM driver Revision: 3.20
[   11.652000] kjournald starting.  Commit interval 5 seconds
[   11.652000] EXT3-fs: sda6: orphan cleanup on readonly fs
[   11.652000] ext3_orphan_cleanup: deleting unreferenced inode 1700758
[   11.680000] ext3_orphan_cleanup: deleting unreferenced inode 1700623
[   11.692000] EXT3-fs: sda6: 2 orphan inodes deleted
[   11.692000] EXT3-fs: recovery complete.
[   11.732000] EXT3-fs: mounted filesystem with ordered data mode.
[   21.256000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   21.256000] shpchp: Standard Hot Plug PCI Controller Driver version:
0.4
[   21.668000] Linux agpgart interface v0.102 (c) Dave Jones
[   22.044000] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[   22.044000] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[   22.260000] ieee80211_crypt: registered algorithm 'NULL'
[   22.260000] ieee80211: 802.11 data/management/control stack,
git-1.1.13
[   22.260000] ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno em linux.intel.com>
[   22.416000] input: PC Speaker as /class/input/input3
[   22.428000] bcm43xx driver
[   22.432000] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 19
[   22.432000] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LK1E] -> GSI
19 (level, high) -> IRQ 20
[   22.432000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[   22.468000] nvidia: module license 'NVIDIA' taints kernel.
[   22.756000] ACPI: PCI Interrupt Link [LK3E] enabled at IRQ 18
[   22.756000] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LK3E] -> GSI
18 (level, high) -> IRQ 21
[   22.756000] PCI: Setting latency timer of device 0000:00:05.0 to 64
[   22.756000] NVRM: loading NVIDIA UNIX x86 Kernel Module  100.14.19
Wed Sep 12 14:12:24 PDT 2007
[   23.204000] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 17
[   23.204000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI
17 (level, high) -> IRQ 22
[   23.204000] PCI: Setting latency timer of device 0000:00:10.1 to 64
[   23.576000] ieee80211_crypt: registered algorithm 'WEP'
[   23.584000] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps:
0xa04713/0x200000
[   23.644000] input: SynPS/2 Synaptics TouchPad as /class/input/input4
[   24.076000] SoftMAC: Open Authentication completed with
00:19:5b:bb:84:b1
[   24.216000] loop: module loaded
[   24.296000] lp: driver loaded but no devices found
[   24.432000] Adding 714852k swap on /dev/sda7.  Priority:-1 extents:1
across:714852k
[   24.456000] NET: Registered protocol family 10
[   24.456000] lo: Disabled Privacy Extensions
[   25.068000] EXT3 FS on sda6, internal journal
[   26.740000] No dock devices found.
[   26.768000] ACPI: Battery Slot [BAT0] (battery present)
[   26.876000] ACPI: AC Adapter [ACAD] (on-line)
[   26.936000] input: Power Button (FF) as /class/input/input5
[   26.940000] ACPI: Power Button (FF) [PWRF]
[   26.984000] input: Power Button (CM) as /class/input/input6
[   26.988000] ACPI: Power Button (CM) [PWRB]
[   27.028000] input: Sleep Button (CM) as /class/input/input7
[   27.032000] ACPI: Sleep Button (CM) [SLPB]
[   27.076000] input: Lid Switch as /class/input/input8
[   27.080000] ACPI: Lid Switch [LID]
[   27.096000] ACPI: Video Device [UVGA] (multi-head: yes  rom: no
post: no)
[   27.100000] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post:
no)
[   27.384000] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor
3400+ processors (version 2.00.00)
[   27.384000] powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x10
[   27.384000] powernow-k8:    1 : fid 0x8 (1600 MHz), vid 0x12
[   27.384000] powernow-k8:    2 : fid 0x0 (800 MHz), vid 0x18
[   28.468000] ppdev: user-space parallel port driver
[   28.608000] eth1: no link during initialization.
[   28.608000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   29.012000] apm: BIOS not found.
[   32.060000] Clocksource tsc unstable (delta = -277796536 ns)
[   32.136000] Bluetooth: Core ver 2.11
[   32.136000] NET: Registered protocol family 31
[   32.136000] Bluetooth: HCI device and connection manager initialized
[   32.136000] Bluetooth: HCI socket layer initialized
[   32.164000] Bluetooth: L2CAP ver 2.8
[   32.164000] Bluetooth: L2CAP socket layer initialized
[   32.224000] Bluetooth: RFCOMM socket layer initialized
[   32.224000] Bluetooth: RFCOMM TTY layer initialized
[   32.224000] Bluetooth: RFCOMM ver 1.8
[   34.920000] eth0: no IPv6 routers present
[   59.712000] UDF-fs: No VRS found
[   59.828000] ISO 9660 Extensions: Microsoft Joliet Level 3
[   59.872000] ISOFS: changing to secondary root
[  113.076000] psmouse.c: TouchPad at isa0060/serio1/input0 lost
synchronization, throwing 3 bytes away.
[  113.592000] psmouse.c: resync failed, issuing reconnect request
[  233.564000] usb 1-2: new high speed USB device using ehci_hcd and
address 3
[  233.700000] usb 1-2: configuration #1 chosen from 1 choice
[  257.676000] usb 1-2: USB disconnect, address 3
[  258.500000] usb 1-2: new high speed USB device using ehci_hcd and
address 4
[  258.632000] usb 1-2: configuration #1 chosen from 1 choice
[  258.912000] usbcore: registered new interface driver libusual
[  259.044000] Initializing USB Mass Storage driver...
[  259.044000] scsi2 : SCSI emulation for USB Mass Storage devices
[  259.044000] usb-storage: device found at 4
[  259.044000] usb-storage: waiting for device to settle before scanning
[  259.044000] usbcore: registered new interface driver usb-storage
[  259.048000] USB Mass Storage support registered.
[  264.044000] usb-storage: device scan complete
[  264.044000] scsi 2:0:0:0: Direct-Access     palmOne, File storage
1.0  PQ: 0 ANSI: 0
[  264.048000] scsi 2:0:0:1: Direct-Access
1.0  PQ: 1 ANSI: 0
[  264.052000] sd 2:0:0:0: [sdb] 7818112 512-byte hardware sectors (4003
MB)
[  264.056000] sd 2:0:0:0: [sdb] Write Protect is off
[  264.056000] sd 2:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[  264.056000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  264.060000] sd 2:0:0:0: [sdb] 7818112 512-byte hardware sectors (4003
MB)
[  264.060000] sd 2:0:0:0: [sdb] Write Protect is off
[  264.060000] sd 2:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[  264.060000] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  264.060000]  sdb: sdb1
[  264.360000] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[  264.360000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[  264.360000] scsi 2:0:0:1: Attached scsi generic sg2 type 0

Mas mesmo assim sem sucesso no sincronismo.

Em Seg, 2007-11-05 às 23:07 -0200, Duda Nogueira escreveu:
> Oi Renato!
> 
> Ao espetar o aparelho no linux via USB, ele reconhece direito no linux?
> 
> assim que espetar, digite dmesg no terminal e cole o resultado aqui.
> 
> às vezes ele joga pra ttyUSBS1 ou 0 ou 2... às vezes ja cria 1 link pra
> /dev/pilot...
> 
> aproveita e manda 1
> 
> ls -all /dev/pilot
> 
> 
> Até!
> 
> On Nov 5, 2007 10:03 PM, Renato Resende Batista <zenatuz em gmail.com> wrote:
> 
> > Olá Duda, tentei seguindo as orientações do endereço e apareceu a
> > seguinte mensagem:
> >
> > "Falha na conexão utilizando o dispositivo 'Lifedrive', na porta
> > '/dev/ttyS1'. Verifique sua configuração, como foi solicitado 'ttyUSB',
> > porém não existe o módulo do kernel usbserial 'visor' carregado. Você
> > pode precisar selecionar um dipositivo 't"
> >
> > Tentei várias vezes, mas sem sucesso.
> >
> >
> > Em Seg, 2007-11-05 às 21:27 -0200, Duda Nogueira escreveu:
> > > Oi Renato!
> > >
> > > Publiquei em meu site uma dica mto boa sobre sincronização com palm:
> > >
> > >
> > http://dudanogueira.com.br/2006/11/25/sincronizando-o-seu-palm-no-ubuntu-e-mais-syncevolution-funambol/
> > >
> > > Abraços!
> > >
> > > On Nov 5, 2007 6:13 PM, Renato Resende Batista <zenatuz em gmail.com>
> > wrote:
> > >
> > > > Olá a todos,
> > > >        Tentei por algumas vezes fazer o sincronismo de um dispositivo
> > Palm
> > > > (LifeDrive) através do Gnome Pilot, mas não consegui êxito, alguém
> > > > possui algum outro software ou instruções para que possa fazer o
> > > > sincronismo?
> > > >
> > > >
> > > >        Outra dúvida é a respeito de sincronismo mas de um celular
> > symbian.
> > > > Alguma dica sobre isso?
> > > >
> > > >        Atenciosamente,
> > > >        Renato R.Batista.
> > > >
> > > >
> > > > --
> > > > Interessado em aprender mais sobre o Ubuntu em português?
> > > > http://wiki.ubuntu-br.org/ComeceAqui  -
> > > > ubuntu-br mailing list
> > > > ubuntu-br em lists.ubuntu.com
> > > > https://lists.ubuntu.com/mailman/listinfo/ubuntu-br
> > > >
> > >
> > >
> > >
> > > --
> > > Duda Nogueira
> > > Tecnologia e WEB
> > > http://dudanogueira.com.br
> > > -------------------------------------
> > > EMAIL: dudanogueira em ubuntu.com
> > > GOOGLE: dudanogueira em gmail.com
> > > SKYPE: dudanogueirabr
> >
> >
> > --
> > Interessado em aprender mais sobre o Ubuntu em português?
> > http://wiki.ubuntu-br.org/ComeceAqui  -
> > ubuntu-br mailing list
> > ubuntu-br em lists.ubuntu.com
> > https://lists.ubuntu.com/mailman/listinfo/ubuntu-br
> >
> 
> 
> 
> -- 
> Duda Nogueira
> Tecnologia e WEB
> http://dudanogueira.com.br
> -------------------------------------
> EMAIL: dudanogueira em ubuntu.com
> GOOGLE: dudanogueira em gmail.com
> SKYPE: dudanogueirabr





More information about the ubuntu-br mailing list