[ubuntu/noble-proposed] linux-qcom 6.8.0-1055.55 (Accepted)

[Andy Whitcroft]

linux-qcom (6.8.0-1055.55) noble; urgency=medium

  * noble/linux-qcom: 6.8.0-1055.55 -proposed tracker (LP: #2123917)

  * Bringing up RPI IMX577 in RB4
    - ARM: dts: msm: Camera: Add dtsi for RB4 4xPMIC dev
    - ARM: msm: dts: camera: Add support for RPi imx577 sensor
    - SAUCE: dts: qcom: add 2 qcs8275 platforms in the makefile

  * [RB8] 0004-QCLINUX-net-stmmac-Add-EEPROM-support-to-driver.patch feedback
    - Revert "QCLINUX: net: stmmac: Add EEPROM support to driver"

  * [RB8] FAN inverted PWN handling
    - hwmon: (amc6821) Add PWM polarity configuration with OF
    - SAUCE: dts: qcom: add pwm polarity for fan

  * [QC] Using mbn instead of mdt
    - arm64: dts: qcom: switch from .mdt to .mbn firmwares

  * RB4 Audio BU with TPLG support
    - RB4: support tplg based soundcard

  * Miscellaneous upstream changes
    - arm64: dts: rubikpi: add RUBIK Pi related basic device tree
    - arm64: dts: rubikpi: compatible with USB-A 2.0 port
    - arm64: dts: rubikpi: enable USB3.0 HUB
    - arm64: dts: rubikpi: enable M.2 port
    - net: ax88179b: add driver
    - arm64: dts: rubikpi: enable fan
    - arm64: defconfig: enable ax88179b config
    - wifi: ap6256: add driver
    - arm64: dts: rubikpi: enable Wi-Fi
    - arm64: dts: rubikpi3: enable bluetooth
    - serial: qcom-geni: increase uart ports to 13
    - arm64: dts: rubikpi: enable rtc to support time writing
    - arm64: dts: rubikpi: camera: bringup imx219 and imx477
    - drm/bridge: lt9611: rubikpi: enable hdmi out
    - arm64: dts: rubikpi3: enable hdmi out interface
    - ASoC: es8316: rubikpi: enable 3.5mm headphone jack
    - arm64: dts: rubikpi3: enable 3.5mm headphone jack
    - spi: spidev: add an entry for thundercomm,rubikpi
    - arm64: dts: rubikpi: enable bus interface on 40 pin
    - ASoC: qcom: qcm6490: rubikpi: enable HDMI OUT audio
    - arm64: dts: rubikpi3: enable HDMI OUT audio
    - arm64: dts: rubikpi3: Enable Bluetooth kernel driver
    - drm/bridge: lt9611: rubikpi: fix the problem of hot plug failure
    - arm64: dts: rubikpi3: modify the interrupt trigger mode of HDMI out
    - arm64: dts: rubikpi: camera: Remove unnecessary gpio controls
    - Ubuntu: [Config] update CONFIG options for Rubik Pi 3
    - drm/bridge: lt9611: rubikpi: fix some HDMI monitors cannot display
    - arm64: dts: rubikpi3: added min-vblank configuration for hdmi function
    - HID: multitouch: Add support for QinHeng Electronics USB2IIC_CTP_CONTROL
    - soc: qcom: pmic_glink: resolve compilation errors
    - arm64: dts: rubikpi3: Increase temperature trigger point
    - arm64: dts: rubikpi3: Enable USB Type-C display
    - arm64: dts: rubikpi3: change device tree name
    - arm64: dts: rubikpi3: set the Bluetooth serial port baud rate to 3Mbps
    - arm64: dts: rubikpi3: remove pm7325b
    - ASoC: qcom: qdsp6: q6apm: add S32_LE format support for hw playback
    - ASoC: qcom: qcm6490: roll back qcm6490.c to its original state
    - ASoC: qcom: qcm6490: rubikpi: add support for RubikPi3 board
    - ASoC: codecs: es8316: enable MCLK
    - arm64: dts: rubikpi3: modify dtsi to enable kernel ALSA PCM
    - arm64: dts: rubikpi3: switch the USB2.0 Type-A port to OTG mode
    - ASoC: codecs: es8316: roll back the es8316 driver to its original state
    - ASoC: codecs: es8316: modify the es8316 driver to adapt to RubikPi3
    - arm64: dts: rubikpi3: modify the es8316 power supply pin
    - wifi: ap6256: disable configuration file hash detection
    - drm/bridge: lt9611: roll back the lt9611 driver to its original state
    - drm/bridge: lt9611: modify the lt9611 driver to adapt to RubikPi3
    - arm64: dts: rubikpi3: adjust the register configuration of LT9611
    - Ubuntu: [Config] Disable bcmdhd wifi driver

Date: 2025-09-17 01:09:12.951881+00:00
Changed-By: Hui Wang <hui.wang at canonical.com>
Signed-By: Andy Whitcroft <apw at canonical.com>
https://launchpad.net/ubuntu/+source/linux-qcom/6.8.0-1055.55
-------------- next part --------------
Sorry, changesfile not available.