Ubuntu 7.10 Nic card problem

[Rapha Baroudi]

I need help, I have a Dell Inspiron 2650 and I just installed Ubuntu on it
version 7.10

i got those readying

 Code:

Module			Size Used By
rfcomm			42136 2
12cap			26240 11 rfcomm

bluetooth		57060 4rfcomm,12cap
ppdev			10244 0
speedstep_ich		6416 0
speedstep_lib		6404 1 speedstep_ich
cpufreq_ondemand	9612 1
cpufreq_userspace	5280 0
cpufreq_stats		7232 0
freq_table		5792 3speedstep_ich,cpufreq_ondemand.cpufreq_status

cpufreq_powersave	2688 0
cpufreq_conservative	8072 0
ac			6148 0
dock			10656 0
button			8976 0
sbs			19592 0
container		5504 0
video			18060 0
battery			11012 0
lp			12580 0
bcm43xx			127336 0

ieee80211softmac	31360 1 bcm43xx
ieee80211		35656 2 bcm43xx,ieee80211softmac
ieee80211_crypt		7040 1 ieee80211
joydev			11328 0
snd_inte18x0		34972 1
snd_ac97_codec		100644 1 snd_inte18x0
ac97_bus		3200 1 snd_ac97_codec

snd_pcm_oss		44672 0
snd_mixer_oss		17664 1 snd_pcm_oss
snd_pcm			80388 3 snd_inte18x0,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy		4740 0
pcmcia			41388 0
snd_seq_oss		33152 0
snd_seq_midi		9600 0
snd_rawmidi		25728 1 snd_seq_midi

i2c_core		26112 0
yenta_socket		27532 2
rsrc_nonstatic		14080 1 yenta_socket
parport_pc		37412 1
parport			37448 3 ppdev,lp,parport_pc
snd_seq_midi_event	8448 2 snd_seq_oss,snd_seq_midi
snd_seq			53232 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event

snd_timer		24324 2 snd_pcm,snd_seq
snd_seq_device		9288 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
pcmcia_core		40980 3 pcmia,yenta_socket,rsrc_nonstatic
serio_raw		8068 0
psmouse			39952 0

snd			54660 12
snd_inte18x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore		8800 1 snd
snd_page_alloc		11440 2 snd_inte18x0,snd_pcm
iTCO_wdt		11940 0

intel_agp		25620 1
iTCO_vendor_support	4868 1 iTCO_wdt
shpchp			34580 0
pci_hotplug		32704 1 shpchp
agpgart			35016 1 intel_agp
evdev			11136 6
ext3			133896 1
jbd			60456 1 ext3
mbcache			9732 1 ext3

sg			36764 0
sr_mod			17828 0
cdrom			37536 1 sr_mod
sd_mod			30336 3
ata_generic		8452 0
floppy			60004 0
3c59x			46632 0
mii			6528 1 3c59x
ata_piix		17540 2
libata			125168 2 ata_generic,ata_piix

scse_mod		147084 4 sg,sr_mod.sd_mod,libata
uhci_hcd		26640 0
usbcore			138632 2 uhci_hcd
thermal			14344 0
processor		32072 1 thermal
fan			5764 0
fuse			47124 0
apparmor		40728 0
commoncap		8320 1 apparmor

and my Wired Connection:Address:dhcp, but when i clicked on properties it
does not show an IP address or subnet Mask or gateway address all these
fields are empty.

In my Network tools I have both a loop back interface and Ethernet interface
(eth0) but all the interface information on both of them says not available.
Also, on the Network Device when i click on Ethernet Interface (eth0) the
configure button is disabled....

Also i did this,

I ran the following commands:

rbaroudi at RAF:~$ lspci
00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host
Bridge (rev 05)
00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP
Bridge (rev 05)
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB Controller #1 (rev
02)
00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB Controller #2 (rev
02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev
02)
00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97
Audio Controller (rev 02)
00:1f.6 Modem: Intel Corporation 82801CA/CAM AC'97 Modem Controller (rev 02)

01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 Go]
(rev b2)
02:01.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
78)
02:04.0 CardBus bridge: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus
Controller
03:00.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g]
802.11g Wireless LAN Controller (rev 02)
rbaroudi at RAF:~$ ifstatus eth0
The program 'ifstatus' is currently not installed. You can install it by
typing:
sudo apt-get install ifplugd
You will have to enable component called 'universe'
bash: ifstatus: command not found
rbaroudi at RAF:~$ ifstatus eth1
The program 'ifstatus' is currently not installed. You can install it by
typing:
sudo apt-get install ifplugd
You will have to enable component called 'universe'
bash: ifstatus: command not found
rbaroudi at RAF:~$


also, my Nic is not wireless its an Ethernet port with wired LAN..

I believe that my cable is good i just tested it, but i believe its a
routing problem because the IP address and subnet mask fields are empty, and
i dont know what to type in them.

Please, consider helping me with this....i tried the forums for over a month
and no one could help me with it, so please, if you got time i would
certainly appreciate it. Thanks again :)

Raphael Baroudi

-- 
Joshua 24:15
-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://lists.ubuntu.com/archives/laptop-testing-team/attachments/20080201/7517aa38/attachment.htm