Ubuntu Breezy on Dell Latitude D810
Per Arne Nilssen
systemansvarlig at vagaungdomsskule.no
Fri Aug 26 07:02:36 CDT 2005
Hi,
I will try as best as I can to inform the LaptopTesting team about my
progress with Ubuntu Breezy on my Dell Latitude D810.
I removed all partitions and did an fdisk /mbr before I installed Breezy.
I did use the daily image from 24 august 2005, downloaded from
http://cdimage.ubuntulinux.org/
The install did work without any major problems. (I had to choose Erease
whole disk SCSI1....don't fully remember what it said. But choosing
.....LVM..... didn't work for me.)
I have some issues now, these did work perfectly on Ubuntu Hoary.
* I get some error messages on startup. What kind of log shall I
look at to see my boot messages?
* The scroll wheel on my cordless MouseMan Optical USB mouse does
not work.
* When I plug in my portable Seagate HD trough USB I don't a
shortcut on my desktop. I don't find it at all. Or that's not true
I can see the disk when I go this way -> System -> Administration
-> Disks. My USB disk is there but I can't access it.
perarne at ubuntu:~$ sudo tail -f /var/log/syslog
Password:
Aug 25 19:35:13 ubuntu -- MARK --
Aug 25 19:55:13 ubuntu -- MARK --
Aug 25 20:15:13 ubuntu -- MARK --
Aug 25 20:17:01 ubuntu /USR/SBIN/CRON[8631]: (root) CMD ( run-parts
--report / etc/cron.hourly)
Aug 25 20:35:13 ubuntu -- MARK --
Aug 25 20:52:10 ubuntu kernel: [4308917.630000] atkbd.c: Unknown key
pressed (tr anslated set 2, code 0x8a on isa0060/serio0).
Aug 25 20:52:10 ubuntu kernel: [4308917.630000] atkbd.c: Use
'setkeycodes e00a < keycode>' to make it known.
Aug 25 21:15:13 ubuntu -- MARK --
Aug 25 21:17:01 ubuntu /USR/SBIN/CRON[9533]: (root) CMD ( run-parts
--report / etc/cron.hourly)
Aug 25 21:35:13 ubuntu -- MARK --
Aug 25 21:44:09 ubuntu kernel: [4312037.261000] usb 5-5: new high speed
USB device using ehci_hcd and address 2
Aug 25 21:44:09 ubuntu kernel: [4312037.637000] Uniform Multi-Platform
E-IDE driver Revis ion: 7.00alpha2
Aug 25 21:44:09 ubuntu kernel: [4312037.637000] ide: Assuming 33MHz
system bus speed for PIO modes; override with idebus=xx
Aug 25 21:44:09 ubuntu kernel: [4312037.637000] ACPI: bus type ide
registered
Aug 25 21:44:09 ubuntu kernel: [4312037.646000] Initializing USB Mass
Storage driver...
Aug 25 21:44:09 ubuntu kernel: [4312037.652000] scsi2 : SCSI emulation
for USB Mass Stora ge devices
Aug 25 21:44:09 ubuntu kernel: [4312037.653000] usb-storage: device
found at 2
Aug 25 21:44:09 ubuntu kernel: [4312037.653000] usb-storage: waiting for
device to settle before scanning
Aug 25 21:44:09 ubuntu kernel: [4312037.654000] usbcore: registered new
driver usb-storag e
Aug 25 21:44:09 ubuntu kernel: [4312037.654000] USB Mass Storage support
registered.
Aug 25 21:44:09 ubuntu usb.agent[9977]: usb-storage: loaded
successfully
Aug 25 21:44:14 ubuntu kernel: [4312042.653000] Vendor: ST910082
Model: 3A Rev: 0 0
Aug 25 21:44:14 ubuntu kernel: [4312042.653000] Type:
Direct-Access ANSI SCSI revision: 00
Aug 25 21:44:14 ubuntu kernel: [4312042.659000] SCSI device sdb:
195371568 512-byte hdwr sectors (100030 MB)
Aug 25 21:44:14 ubuntu kernel: [4312042.659000] sdb: assuming drive
cache: write through
Aug 25 21:44:14 ubuntu kernel: [4312042.662000] SCSI device sdb:
195371568 512-byte hdwr sectors (100030 MB)
Aug 25 21:44:14 ubuntu kernel: [4312042.662000] sdb: assuming drive
cache: write through
Aug 25 21:44:14 ubuntu kernel: [4312042.662000]
/dev/scsi/host2/bus0/target0/lun0: p1
Aug 25 21:44:14 ubuntu kernel: [4312042.687000] Attached scsi disk sdb
at scsi2, channel 0, id 0, lun 0
Aug 25 21:44:14 ubuntu kernel: [4312042.687000] Attached scsi generic
sg2 at scsi2, chann el 0, id 0, lun 0, type 0
Aug 25 21:44:14 ubuntu kernel: [4312042.690000] usb-storage: device scan
complete
Aug 25 21:44:14 ubuntu scsi.agent[10058]: sd_mod: loaded
sucessfully (for disk)
* When I try to edit preferences on icons on the gnome-panel, I
get error and gnome-panel closes and goes up again.
(This does not happend if the icon is on my desktop.)
* What do I have to do to get my wireless to work?
perarne at ubuntu:/etc/X11$ dmesg | grep ipw
[4294692.813000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network
Driver, 1.0.6
[4294692.813000] ipw2200: Copyright(c) 2003-2004 Intel Corporation
[4294692.816000] ipw2200: Detected Intel PRO/Wireless 2200BG Network
Connection
Here are also my whole dmesg:
perarne at ubuntu:/var/log$ dmesg
0-0x107f has been reserved
[4294668.594000] pnp: 00:02: ioport range 0x1080-0x10bf has been reserved
[4294668.594000] pnp: 00:02: ioport range 0x10c0-0x10df has been reserved
[4294668.594000] pnp: 00:07: ioport range 0x900-0x90f has been reserved
[4294668.594000] pnp: 00:07: ioport range 0x910-0x91f has been reserved
[4294668.594000] pnp: 00:07: ioport range 0x920-0x92f has been reserved
[4294668.594000] pnp: 00:07: ioport range 0x93c-0x93f has been reserved
[4294668.594000] pnp: 00:07: ioport range 0x940-0x97f has been reserved
[4294668.594000] pnp: 00:0b: ioport range 0x930-0x93b has been reserved
[4294668.594000] audit: initializing netlink socket (disabled)
[4294668.594000] audit(1124981684.592:0): initialized
[4294668.594000] highmem bounce pool size: 64 pages
[4294668.594000] VFS: Disk quotas dquot_6.5.1
[4294668.594000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294668.594000] devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
[4294668.594000] devfs: boot_options: 0x0
[4294668.594000] Initializing Cryptographic API
[4294668.594000] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level,
low) -> IRQ 16
[4294668.594000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[4294668.594000] assign_interrupt_mode Found MSI capability
[4294668.594000] Allocate Port Service[pcie00]
[4294668.594000] Allocate Port Service[pcie03]
[4294668.594000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level,
low) -> IRQ 16
[4294668.594000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[4294668.594000] assign_interrupt_mode Found MSI capability
[4294668.594000] Allocate Port Service[pcie00]
[4294668.594000] Allocate Port Service[pcie02]
[4294668.594000] Allocate Port Service[pcie03]
[4294668.595000] isapnp: Scanning for PnP cards...
[4294668.948000] isapnp: No Plug & Play device found
[4294668.962000] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[4294668.966000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294668.966000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294668.966000] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports,
IRQ sharing enabled
[4294668.966000] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294668.968000] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294668.968000] io scheduler noop registered
[4294668.968000] io scheduler anticipatory registered
[4294668.968000] io scheduler deadline registered
[4294668.968000] io scheduler cfq registered
[4294668.968000] RAMDISK driver initialized: 16 RAM disks of 8192K size
1024 blocksize
[4294668.969000] EISA: Probing bus 0 at eisa.0
[4294668.969000] Cannot allocate resource for EISA slot 1
[4294668.969000] EISA: Detected 0 cards.
[4294668.969000] NET: Registered protocol family 2
[4294668.978000] IP: routing cache hash table of 8192 buckets, 64Kbytes
[4294668.978000] TCP established hash table entries: 262144 (order: 9,
2097152 bytes)
[4294668.979000] TCP bind hash table entries: 65536 (order: 6, 262144
bytes)
[4294668.980000] TCP: Hash tables configured (established 262144 bind
65536)
[4294668.980000] NET: Registered protocol family 8
[4294668.980000] NET: Registered protocol family 20
[4294668.980000] input: AT Translated Set 2 keyboard on isa0060/serio0
[4294668.980000] ACPI wakeup devices:
[4294668.980000] LID PBTN PCI0 USB0 USB1 USB2 USB4 USB3 MODM PCIE NIC
[4294668.980000] ACPI: (supports S0 S3 S4 S4bios S5)
[4294668.980000] Freeing unused kernel memory: 224k freed
[4294669.005000] Capability LSM initialized
[4294669.034000] usbcore: registered new driver usbfs
[4294669.034000] usbcore: registered new driver hub
[4294669.034000] USB Universal Host Controller Interface driver v2.2
[4294669.035000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level,
low) -> IRQ 16
[4294669.035000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[4294669.035000] uhci_hcd 0000:00:1d.0: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
[4294669.097000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 1
[4294669.097000] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[4294669.097000] hub 1-0:1.0: USB hub found
[4294669.097000] hub 1-0:1.0: 2 ports detected
[4294669.100000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level,
low) -> IRQ 17
[4294669.100000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[4294669.100000] uhci_hcd 0000:00:1d.1: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
[4294669.162000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 2
[4294669.162000] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[4294669.162000] hub 2-0:1.0: USB hub found
[4294669.162000] hub 2-0:1.0: 2 ports detected
[4294669.165000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 18
[4294669.165000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[4294669.165000] uhci_hcd 0000:00:1d.2: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
[4294669.227000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 3
[4294669.227000] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[4294669.227000] hub 3-0:1.0: USB hub found
[4294669.227000] hub 3-0:1.0: 2 ports detected
[4294669.230000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level,
low) -> IRQ 19
[4294669.230000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[4294669.230000] uhci_hcd 0000:00:1d.3: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
[4294669.292000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned
bus number 4
[4294669.292000] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[4294669.292000] hub 4-0:1.0: USB hub found
[4294669.292000] hub 4-0:1.0: 2 ports detected
[4294669.318000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level,
low) -> IRQ 16
[4294669.318000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[4294669.318000] ehci_hcd 0000:00:1d.7: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
[4294669.318000] ehci_hcd 0000:00:1d.7: debug port 1
[4294669.318000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 5
[4294669.318000] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xffa80800
[4294669.321000] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[4294669.321000] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00,
driver 10 Dec 2004
[4294669.322000] hub 5-0:1.0: USB hub found
[4294669.322000] hub 5-0:1.0: 8 ports detected
[4294669.366000] SCSI subsystem initialized
[4294669.367000] libata version 1.11 loaded.
[4294669.368000] ahci version 1.00
[4294669.368000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level,
low) -> IRQ 17
[4294669.368000] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[4294669.368000] ahci: probe of 0000:00:1f.2 failed with error -12
[4294669.369000] ata_piix version 1.03
[4294669.369000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level,
low) -> IRQ 17
[4294669.369000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[4294669.369000] ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma
0xBFA0 irq 14
[4294669.539000] ata1: dev 0 cfg 49:2b00 82:346b 83:5b29 84:4003 85:3469
86:1a09 87:4003 88:203f
[4294669.539000] ata1: dev 0 ATA, max UDMA/100, 117210240 sectors:
[4294669.541000] ata1: dev 0 configured for UDMA/100
[4294669.541000] scsi0 : ata_piix
[4294669.541000] Vendor: ATA Model: FUJITSU MHT2060A Rev: 006C
[4294669.541000] Type: Direct-Access ANSI SCSI
revision: 05
[4294669.542000] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma
0xBFA8 irq 15
[4294669.847000] ata2: dev 0 cfg 49:0b00 82:0210 83:1000 84:0000 85:0000
86:0000 87:0000 88:0407
[4294669.847000] ata2: dev 0 ATAPI, max UDMA/33
[4294669.847000] ata2: dev 0 configured for UDMA/33
[4294669.847000] scsi1 : ata_piix
[4294669.848000] Vendor: SONY Model: DVD+-RW DW-D56A Rev: PDS3
[4294669.848000] Type: CD-ROM ANSI SCSI
revision: 05
[4294669.872000] tg3.c:v3.31 (June 8, 2005)
[4294669.872000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level,
low) -> IRQ 16
[4294669.872000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[4294669.877000] eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)]
(PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:11:43:75:d0:18
[4294669.877000] eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0]
WireSpeed[1] TSOcap[1]
[4294669.877000] eth0: dma_rwctrl[76180000]
[4294671.926000] SCSI device sda: 117210240 512-byte hdwr sectors (60012
MB)
[4294671.926000] SCSI device sda: drive cache: write back
[4294671.926000] SCSI device sda: 117210240 512-byte hdwr sectors (60012
MB)
[4294671.926000] SCSI device sda: drive cache: write back
[4294671.926000] /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 >
[4294672.039000] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[4294672.181000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[4294672.181000] ACPI: Processor [CPU0] (supports 8 throttling states)
[4294672.185000] ACPI: Thermal Zone [THM] (52 C)
[4294672.215000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel at redhat.com
[4294672.225000] Attempting manual resume
[4294672.226000] swsusp: Suspend partition has wrong signature?
[4294672.256000] kjournald starting. Commit interval 5 seconds
[4294672.256000] EXT3-fs: mounted filesystem with ordered data mode.
[4294673.285000] NET: Registered protocol family 1
[4294674.012000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294676.265000] Adding 2409708k swap on /dev/sda5. Priority:-1 extents:1
[4294676.412000] EXT3 FS on sda1, internal journal
[4294684.155000] lp: driver loaded but no devices found
[4294684.166000] mice: PS/2 mouse device common for all mice
[4294684.555000] input: PS/2 Mouse on isa0060/serio1
[4294684.556000] input: AlpsPS/2 ALPS GlidePoint on isa0060/serio1
[4294688.828000] Linux agpgart interface v0.101 (c) Dave Jones
[4294688.833000] agpgart: Detected an Intel 915GM Chipset.
[4294688.861000] agpgart: AGP aperture is 256M @ 0x0
[4294688.912000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294688.915000] shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
[4294688.915000] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
[4294688.973000] shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
[4294688.973000] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
[4294689.171000] hw_random: cannot enable RNG, aborting
[4294689.294000] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level,
low) -> IRQ 16
[4294689.295000] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[4294690.105000] intel8x0_measure_ac97_clock: measured 49504 usecs
[4294690.105000] intel8x0: clocking to 48000
[4294690.613000] Linux Kernel Card Services
[4294690.613000] options: [pci] [cardbus] [pm]
[4294690.621000] PCI: Enabling device 0000:03:01.0 (0000 -> 0002)
[4294690.621000] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level,
low) -> IRQ 19
[4294690.621000] Yenta: CardBus bridge found at 0000:03:01.0 [1028:0186]
[4294690.741000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 19
[4294690.741000] Socket status: 30000006
[4294690.824000] ieee80211_crypt: registered algorithm 'NULL'
[4294690.827000] ieee80211: 802.11 data/management/control stack, 1.0.3
[4294690.827000] ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno at linux.intel.com>
[4294690.833000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network
Driver, 1.0.6
[4294690.833000] ipw2200: Copyright(c) 2003-2004 Intel Corporation
[4294690.836000] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level,
low) -> IRQ 17
[4294690.836000] ipw2200: Detected Intel PRO/Wireless 2200BG Network
Connection
[4294691.117000] ipw2200: Radio Frequency Kill Switch is On:
[4294691.117000] Kill switch must be turned off for wireless networking
to work.
[4294692.294000] Real Time Clock Driver v1.12
[4294692.317000] input: PC Speaker
[4294692.678000] ts: Compaq touchscreen protocol output
[4294692.860000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2
cdda tray
[4294692.860000] Uniform CD-ROM driver Revision: 3.20
[4294692.861000] Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
[4294692.872000] Attached scsi generic sg0 at scsi0, channel 0, id 0,
lun 0, type 0
[4294692.872000] Attached scsi generic sg1 at scsi1, channel 0, id 0,
lun 0, type 5
[4294693.202000] NET: Registered protocol family 17
[4294695.141000] tg3: eth0: Link is up at 100 Mbps, full duplex.
[4294695.141000] tg3: eth0: Flow control is off for TX and off for RX.
[4294697.405000] NET: Registered protocol family 10
[4294697.405000] Disabled Privacy Extensions on device c02eb280(lo)
[4294697.405000] IPv6 over IPv4 tunneling driver
[4294704.690000] ACPI: AC Adapter [AC] (on-line)
[4294705.004000] ACPI: Battery Slot [BAT0] (battery present)
[4294705.004000] ACPI: Battery Slot [BAT1] (battery absent)
[4294705.020000] ACPI: Lid Switch [LID]
[4294705.020000] ACPI: Power Button (CM) [PBTN]
[4294705.020000] ACPI: Sleep Button (CM) [SBTN]
[4294705.035000] Using specific hotkey driver
[4294705.073000] ibm_acpi: ec object not found
[4294705.150000] ACPI: Video Device [VID] (multi-head: yes rom: no
post: no)
[4294705.265000] apm: BIOS not found.
[4294706.683000] cs: IO port probe 0x100-0x4ff: excluding 0x370-0x377
0x3f0-0x3ff
[4294706.685000] cs: IO port probe 0x800-0x8ff: clean.
[4294706.686000] cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
[4294706.687000] cs: IO port probe 0xa00-0xaff: clean.
[4294707.015000] Bluetooth: Core ver 2.7
[4294707.015000] NET: Registered protocol family 31
[4294707.015000] Bluetooth: HCI device and connection manager initialized
[4294707.015000] Bluetooth: HCI socket layer initialized
[4294707.025000] Bluetooth: L2CAP ver 2.7
[4294707.025000] Bluetooth: L2CAP socket layer initialized
[4294707.086000] Bluetooth: RFCOMM ver 1.5
[4294707.086000] Bluetooth: RFCOMM socket layer initialized
[4294707.086000] Bluetooth: RFCOMM TTY layer initialized
[4294708.303000] eth0: no IPv6 routers present
[4296348.440000] atkbd.c: Unknown key pressed (translated set 2, code
0x88 on isa0060/serio0).
[4296348.440000] atkbd.c: Use 'setkeycodes e008 <keycode>' to make it
known.
[4308917.630000] atkbd.c: Unknown key pressed (translated set 2, code
0x8a on isa0060/serio0).
[4308917.630000] atkbd.c: Use 'setkeycodes e00a <keycode>' to make it
known.
[4312037.261000] usb 5-5: new high speed USB device using ehci_hcd and
address 2
[4312037.637000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4312037.637000] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[4312037.637000] ACPI: bus type ide registered
[4312037.646000] Initializing USB Mass Storage driver...
[4312037.652000] scsi2 : SCSI emulation for USB Mass Storage devices
[4312037.653000] usb-storage: device found at 2
[4312037.653000] usb-storage: waiting for device to settle before scanning
[4312037.654000] usbcore: registered new driver usb-storage
[4312037.654000] USB Mass Storage support registered.
[4312042.653000] Vendor: ST910082 Model: 3A Rev: 0 0
[4312042.653000] Type: Direct-Access ANSI SCSI
revision: 00
[4312042.659000] SCSI device sdb: 195371568 512-byte hdwr sectors
(100030 MB)
[4312042.659000] sdb: assuming drive cache: write through
[4312042.662000] SCSI device sdb: 195371568 512-byte hdwr sectors
(100030 MB)
[4312042.662000] sdb: assuming drive cache: write through
[4312042.662000] /dev/scsi/host2/bus0/target0/lun0: p1
[4312042.687000] Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
[4312042.687000] Attached scsi generic sg2 at scsi2, channel 0, id 0,
lun 0, type 0
[4312042.690000] usb-storage: device scan complete
Here are also my xorg.conf:
Section "Files"
FontPath "unix/:7100" # local font server
# if the local font server has problems, we can fall back on these
FontPath "/usr/share/X11/fonts/misc"
FontPath "/usr/share/X11/fonts/cyrillic"
FontPath "/usr/share/X11/fonts/100dpi/:unscaled"
FontPath "/usr/share/X11/fonts/75dpi/:unscaled"
FontPath "/usr/share/X11/fonts/Type1"
FontPath "/usr/share/X11/fonts/CID"
FontPath "/usr/share/X11/fonts/100dpi"
FontPath "/usr/share/X11/fonts/75dpi"
# paths to defoma fonts
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/CID"
EndSection
Section "Module"
Load "GLcore"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "type1"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "no"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Identifier "Synaptics Touchpad"
Driver "synaptics"
Option "SendCoreEvents" "true"
Option "Device" "/dev/psaux"
Option "Protocol" "auto-dev"
Option "HorizScrollDelta" "0"
EndSection
Section "Device"
Identifier "ATI Technologies, Inc. Radeon Mobility X600 (M24)"
Driver "ati"
BusID "PCI:1:0:0"
EndSection
Section "Monitor"
Identifier "Generic Monitor"
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "ATI Technologies, Inc. Radeon Mobility X600 (M24)"
Monitor "Generic Monitor"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "1680x1050" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1680x1050" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1680x1050" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1680x1050" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1680x1050" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1680x1050" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "Synaptics Touchpad"
EndSection
Section "DRI"
Mode 0666
EndSection
Pan007
More information about the laptop-testing-team
mailing list