I have what sounds like a berring going bad.

Steven Vollom stevenvollom at sbcglobal.net
Sat Feb 21 00:20:47 GMT 2009


On Friday 20 February 2009 18:49:39 Willy Hamra wrote:
> sudo smartctl --all /dev/sda
Willie,
My 200gb drive seems OK, however the 80gb has a long list of Old Age and 
prefail warnings.  I would like to not lose the data on the drive and don't 
have a place to put it right now, Should I disconnect the drive until I can 
solve the storage problem?

The SMART overall-health self-assessment test result of the 200gb drive:  	
PASSED.  Still there were 30 prefail or old age warnings on it too.

It is a lot of reading, so don't take the time if you choose not to, but I am 
not qualified to make a decision on this.  It really looks to me like both my 
drives are at the end of their use.  What would you do?

Here are the readings:

steven at Yesua:~$ sudo smartctl --all /dev/sda
[sudo] password for steven:                 
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/                        

=== START OF INFORMATION SECTION ===
Model Family:     Maxtor DiamondMax Plus 9 family
Device Model:     Maxtor 6Y200P0                 
Serial Number:    Y61LGAEE                       
Firmware Version: YAR41BW0                       
User Capacity:    203,928,109,056 bytes          
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7                                              
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 0               
Local Time is:    Fri Feb 20 18:54:38 2009 EST                   
SMART support is: Available - device has SMART capability.       
SMART support is: Enabled                                        

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.    
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine 
completed
                                        without error or no self-test has ever  
                                        been run.                               
Total time to complete Offline                                                  
data collection:                 ( 243) seconds.                                
Offline data collection                                                         
capabilities:                    (0x5b) SMART execute Offline immediate.        
                                        Auto Offline data collection on/off 
support.                                                                            
                                        Suspend Offline collection upon new     
                                        command.                                
                                        Offline surface scan supported.         
                                        Self-test supported.                    
                                        No Conveyance Self-test supported.      
                                        Selective Self-test supported.          
SMART capabilities:            (0x0003) Saves SMART data before entering        
                                        power-saving mode.                      
                                        Supports SMART auto save timer.         
Error logging capability:        (0x01) Error logging supported.                
                                        No General Purpose Logging support.     
Short self-test routine                                                         
recommended polling time:        (   2) minutes.                                
Extended self-test routine                                                      
recommended polling time:        (  91) minutes.                                

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:  
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  
WHEN_FAILED RAW_VALUE                                                                
  3 Spin_Up_Time            0x0027   176   001   063    Pre-fail  Always   
In_the_past 20225                                                                    
  4 Start_Stop_Count        0x0032   252   252   000    Old_age   Always       
-       2014                                                                     
  5 Reallocated_Sector_Ct   0x0033   253   253   063    Pre-fail  Always       
-       1                                                                        
  6 Read_Channel_Margin     0x0001   253   253   100    Pre-fail  Offline      -       
0                                                                        
  7 Seek_Error_Rate         0x000a   253   252   000    Old_age   Always       
-       0                                                                        
  8 Seek_Time_Performance   0x0027   253   238   187    Pre-fail  Always       
-       56048                                                                    
  9 Power_On_Minutes        0x0032   183   183   000    Old_age   Always       
-       402h+41m                                                                 
 10 Spin_Retry_Count        0x002b   253   237   157    Pre-fail  Always       
-       0                                                                        
 11 Calibration_Retry_Count 0x002b   253   251   223    Pre-fail  Always       
-       0                                                                        
 12 Power_Cycle_Count       0x0032   248   248   000    Old_age   Always       
-       2151                                                                     
192 Power-Off_Retract_Count 0x0032   253   253   000    Old_age   Always       
-       0                                                                        
193 Load_Cycle_Count        0x0032   253   253   000    Old_age   Always       
-       0                                                                        
194 Temperature_Celsius     0x0032   253   253   000    Old_age   Always       
-       39                                                                       
195 Hardware_ECC_Recovered  0x000a   253   252   000    Old_age   Always       
-       1590                                                                     
196 Reallocated_Event_Count 0x0008   253   253   000    Old_age   Offline      -       
0                                                                        
197 Current_Pending_Sector  0x0008   253   253   000    Old_age   Offline      -       
0                                                                        
198 Offline_Uncorrectable   0x0008   253   253   000    Old_age   Offline      -       
0                                                                        
199 UDMA_CRC_Error_Count    0x0008   029   001   000    Old_age   Offline      -       
616                                                                      
200 Multi_Zone_Error_Rate   0x000a   253   252   000    Old_age   Always       
-       0                                                                        
201 Soft_Read_Error_Rate    0x000a   253   238   000    Old_age   Always       
-       58                                                                       
202 TA_Increase_Count       0x000a   253   252   000    Old_age   Always       
-       0                                                                        
203 Run_Out_Cancel          0x000b   253   252   180    Pre-fail  Always       
-       2                                                                        
204 Shock_Count_Write_Opern 0x000a   253   252   000    Old_age   Always       
-       0                                                                        
205 Shock_Rate_Write_Opern  0x000a   253   252   000    Old_age   Always       
-       0                                                                        
207 Spin_High_Current       0x002a   253   237   000    Old_age   Always       
-       0                                                                        
208 Spin_Buzz               0x002a   253   252   000    Old_age   Always       
-       0                                                                        
209 Offline_Seek_Performnce 0x0024   193   188   000    Old_age   Offline      -       
0                                                                        
 99 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       
0                                                                        
100 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       
0                                                                        
101 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       
0                                                                        

SMART Error Log Version: 1
Warning: ATA error count 972 inconsistent with error log pointer 5

ATA Error Count: 972 (device log contains only the most recent five errors)
        CR = Command Register [HEX]                                        
        FR = Features Register [HEX]                                       
        SC = Sector Count Register [HEX]                                   
        SN = Sector Number Register [HEX]                                  
        CL = Cylinder Low Register [HEX]                                   
        CH = Cylinder High Register [HEX]                                  
        DH = Device/Head Register [HEX]                                    
        DC = Device Command Register [HEX]                                 
        ER = Error register [HEX]                                          
        ST = Status register [HEX]                                         
Powered_Up_Time is measured from power on, and printed as                  
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,                      
SS=sec, and sss=millisec. It "wraps" after 49.710 days.                    

Error 972 occurred at disk power-on lifetime: 19742 hours (822 days + 14 
hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  40 51 3c 8f aa 01 e0  Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 40 8f aa 01 e0 08      00:09:46.608  READ DMA            
  27 00 00 00 00 00 e0 08      00:09:46.592  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 0a      00:09:46.576  IDENTIFY DEVICE            
  ef 03 45 00 00 00 a0 0a      00:09:46.576  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:09:46.576  READ NATIVE MAX ADDRESS EXT     

Error 971 occurred at disk power-on lifetime: 19742 hours (822 days + 14 
hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  40 51 3c 8f aa 01 e0  Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 40 8f aa 01 e0 08      00:09:45.536  READ DMA            
  27 00 00 00 00 00 e0 08      00:09:45.520  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 0a      00:09:45.520  IDENTIFY DEVICE            
  ef 03 45 00 00 00 a0 0a      00:09:45.504  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:09:45.504  READ NATIVE MAX ADDRESS EXT     

Error 970 occurred at disk power-on lifetime: 19742 hours (822 days + 14 
hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  40 51 3c 8f aa 01 e0  Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 40 8f aa 01 e0 08      00:09:44.480  READ DMA            
  27 00 00 00 00 00 e0 08      00:09:44.464  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 0a      00:09:44.448  IDENTIFY DEVICE            
  ef 03 45 00 00 00 a0 0a      00:09:44.448  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:09:44.448  READ NATIVE MAX ADDRESS EXT     

Error 969 occurred at disk power-on lifetime: 19742 hours (822 days + 14 
hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  40 51 3c 8f aa 01 e0  Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 40 8f aa 01 e0 08      00:09:43.424  READ DMA            
  27 00 00 00 00 00 e0 08      00:09:43.408  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 0a      00:09:43.408  IDENTIFY DEVICE            
  ef 03 45 00 00 00 a0 0a      00:09:43.392  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:09:43.392  READ NATIVE MAX ADDRESS EXT     

Error 968 occurred at disk power-on lifetime: 19742 hours (822 days + 14 
hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  40 51 3c 8f aa 01 e0  Error: UNC 60 sectors at LBA = 0x0001aa8f = 109199

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 40 8f aa 01 e0 08      00:09:42.368  READ DMA            
  27 00 00 00 00 00 e0 08      00:09:42.336  READ NATIVE MAX ADDRESS EXT
  ec 00 00 00 00 00 a0 0a      00:09:42.336  IDENTIFY DEVICE            
  ef 03 45 00 00 00 a0 0a      00:09:42.336  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 e0 08      00:09:42.336  READ NATIVE MAX ADDRESS EXT     

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  
LBA_of_first_error                                                                 
# 1  Short captive       Completed without error       00%     13926         -  
# 2  Short captive       Completed without error       00%     13575         -  
# 3  Short captive       Completed without error       00%     13560         -  
# 4  Short captive       Completed without error       00%     13559         -  

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS                  
    1        0        0  Not_testing                          
    2        0        0  Not_testing                          
    3        0        0  Not_testing                          
    4        0        0  Not_testing                          
    5        0        0  Not_testing                          
Selective self-test flags (0x0):                              
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

steven at Yesua:~$ sudo smartctl --all /dev/sdb
[sudo] password for steven:                 
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/                        

=== START OF INFORMATION SECTION ===
Model Family:     Maxtor DiamondMax Plus 9 family
Device Model:     Maxtor 6Y080P0                 
Serial Number:    Y316LC4E                       
Firmware Version: YAR41BW0                       
User Capacity:    81,964,302,336 bytes           
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7                                              
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 0               
Local Time is:    Fri Feb 20 19:10:05 2009 EST                   
SMART support is: Available - device has SMART capability.       
SMART support is: Enabled                                        

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.    
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine 
completed
                                        without error or no self-test has ever  
                                        been run.                               
Total time to complete Offline                                                  
data collection:                 ( 182) seconds.                                
Offline data collection                                                         
capabilities:                    (0x5b) SMART execute Offline immediate.        
                                        Auto Offline data collection on/off 
support.                                                                            
                                        Suspend Offline collection upon new     
                                        command.                                
                                        Offline surface scan supported.         
                                        Self-test supported.                    
                                        No Conveyance Self-test supported.      
                                        Selective Self-test supported.          
SMART capabilities:            (0x0003) Saves SMART data before entering        
                                        power-saving mode.                      
                                        Supports SMART auto save timer.         
Error logging capability:        (0x01) Error logging supported.                
                                        No General Purpose Logging support.     
Short self-test routine                                                         
recommended polling time:        (   2) minutes.                                
Extended self-test routine                                                      
recommended polling time:        (  40) minutes.                                

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:  
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  
WHEN_FAILED RAW_VALUE                                                                
  3 Spin_Up_Time            0x0027   193   189   063    Pre-fail  Always       
-       18980                                                                    
  4 Start_Stop_Count        0x0032   252   252   000    Old_age   Always       
-       2127                                                                     
  5 Reallocated_Sector_Ct   0x0033   253   253   063    Pre-fail  Always       
-       1                                                                        
  6 Read_Channel_Margin     0x0001   253   253   100    Pre-fail  Offline      -       
0                                                                        
  7 Seek_Error_Rate         0x000a   253   252   000    Old_age   Always       
-       0                                                                        
  8 Seek_Time_Performance   0x0027   253   244   187    Pre-fail  Always       
-       49538                                                                    
  9 Power_On_Minutes        0x0032   173   173   000    Old_age   Always       
-       613h+45m                                                                 
 10 Spin_Retry_Count        0x002b   253   246   157    Pre-fail  Always       
-       0                                                                        
 11 Calibration_Retry_Count 0x002b   253   252   223    Pre-fail  Always       
-       0                                                                        
 12 Power_Cycle_Count       0x0032   248   248   000    Old_age   Always       
-       2265                                                                     
192 Power-Off_Retract_Count 0x0032   253   253   000    Old_age   Always       
-       0                                                                        
193 Load_Cycle_Count        0x0032   253   253   000    Old_age   Always       
-       0                                                                        
194 Temperature_Celsius     0x0032   253   253   000    Old_age   Always       
-       29                                                                       
195 Hardware_ECC_Recovered  0x000a   253   252   000    Old_age   Always       
-       1546                                                                     
196 Reallocated_Event_Count 0x0008   253   253   000    Old_age   Offline      -       
0                                                                        
197 Current_Pending_Sector  0x0008   253   253   000    Old_age   Offline      -       
0                                                                        
198 Offline_Uncorrectable   0x0008   253   253   000    Old_age   Offline      -       
0                                                                        
199 UDMA_CRC_Error_Count    0x0008   199   199   000    Old_age   Offline      -       
0                                                                        
200 Multi_Zone_Error_Rate   0x000a   253   252   000    Old_age   Always       
-       0                                                                        
201 Soft_Read_Error_Rate    0x000a   253   248   000    Old_age   Always       
-       2                                                                        
202 TA_Increase_Count       0x000a   253   252   000    Old_age   Always       
-       0                                                                        
203 Run_Out_Cancel          0x000b   253   252   180    Pre-fail  Always       
-       0                                                                        
204 Shock_Count_Write_Opern 0x000a   253   252   000    Old_age   Always       
-       0                                                                        
205 Shock_Rate_Write_Opern  0x000a   253   252   000    Old_age   Always       
-       0                                                                        
207 Spin_High_Current       0x002a   253   246   000    Old_age   Always       
-       0                                                                        
208 Spin_Buzz               0x002a   253   252   000    Old_age   Always       
-       0                                                                        
209 Offline_Seek_Performnce 0x0024   201   199   000    Old_age   Offline      -       
0                                                                        
 99 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       
0                                                                        
100 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       
0                                                                        
101 Unknown_Attribute       0x0004   253   253   000    Old_age   Offline      -       
0                                                                        

SMART Error Log Version: 1
Warning: ATA error count 11 inconsistent with error log pointer 5

ATA Error Count: 11 (device log contains only the most recent five errors)
        CR = Command Register [HEX]                                       
        FR = Features Register [HEX]                                      
        SC = Sector Count Register [HEX]                                  
        SN = Sector Number Register [HEX]                                 
        CL = Cylinder Low Register [HEX]                                  
        CH = Cylinder High Register [HEX]                                 
        DH = Device/Head Register [HEX]                                   
        DC = Device Command Register [HEX]                                
        ER = Error register [HEX]                                         
        ST = Status register [HEX]                                        
Powered_Up_Time is measured from power on, and printed as                 
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,                     
SS=sec, and sss=millisec. It "wraps" after 49.710 days.                   

Error 11 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  84 51 00 00 00 00 f0  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 ff 01 00 00 00 f0 08      00:07:26.176  READ DMA            
  ef 03 46 b3 60 1f f0 08      00:07:26.176  SET FEATURES [Set transfer mode]
  c6 ff 10 b3 60 1f f0 08      00:07:26.176  SET MULTIPLE MODE               
  10 ff 50 b3 60 1f f0 08      00:07:26.160  RECALIBRATE [OBS-4]             
  91 ff 3f 00 00 00 ff 08      00:07:26.160  INITIALIZE DEVICE PARAMETERS 
[OBS-6]                                                                               

Error 10 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  84 51 00 00 00 00 f0  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 ff 01 00 00 00 f0 08      00:06:12.992  READ DMA            
  ef 03 46 fc e2 5d f0 08      00:06:12.992  SET FEATURES [Set transfer mode]
  c6 ff 10 fc e2 5d f0 08      00:06:12.992  SET MULTIPLE MODE               
  10 ff 50 fc e2 5d f0 08      00:06:12.976  RECALIBRATE [OBS-4]             
  91 ff 3f 00 00 00 ff 08      00:06:12.976  INITIALIZE DEVICE PARAMETERS 
[OBS-6]                                                                               

Error 9 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  84 51 00 00 00 00 f0  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 ff 01 00 00 00 f0 08      00:06:05.344  READ DMA            
  ef 03 46 05 26 db f0 08      00:06:05.344  SET FEATURES [Set transfer mode]
  c6 ff 10 05 26 db f0 08      00:06:05.344  SET MULTIPLE MODE               
  10 ff 50 05 26 db f0 08      00:06:05.328  RECALIBRATE [OBS-4]             
  91 ff 3f 00 00 00 ff 08      00:06:05.328  INITIALIZE DEVICE PARAMETERS 
[OBS-6]                                                                               

Error 8 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH                              
  -- -- -- -- -- -- --                              
  84 51 00 00 00 00 f0  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 ff 01 00 00 00 f0 08      00:05:57.696  READ DMA            
  ef 03 46 0f e3 1e f0 08      00:05:57.696  SET FEATURES [Set transfer mode]
  c6 ff 10 0f e3 1e f0 08      00:05:57.696  SET MULTIPLE MODE               
  10 ff 50 0f e3 1e f0 08      00:05:57.680  RECALIBRATE [OBS-4]             
  91 ff 3f 00 00 00 ff 08      00:05:57.680  INITIALIZE DEVICE PARAMETERS 
[OBS-6]                                                                               

Error 7 occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours)
  When the command that caused the error occurred, the device was in an 
unknown state.                                                                          

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 00 00 00 f0  Error: ICRC, ABRT at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 ff 01 00 00 00 f0 08      00:05:50.048  READ DMA
  c6 03 10 3f fe 3f b0 08      00:05:47.872  SET MULTIPLE MODE
  ef 03 46 3f fe 3f b0 08      00:05:47.872  SET FEATURES [Set transfer mode]
  40 00 01 3f fe 3f bf 08      00:05:47.872  READ VERIFY SECTOR(S)
  10 00 3f 3f 00 00 bf 08      00:05:47.856  RECALIBRATE [OBS-4]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  
LBA_of_first_error
# 1  Short captive       Completed without error       00%     17564         -
# 2  Short captive       Completed without error       00%     17214         -
# 3  Short captive       Completed without error       00%     17199         -
# 4  Short captive       Completed without error       00%     17198         -
# 5  Short offline       Interrupted (host reset)      70%      2447         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

steven at Yesua:~$

Thanks either way.

Steven



More information about the kubuntu-users mailing list