vonage v-phone and modules

Michael W. Holdeman lists at ptfd.org
Wed Feb 21 03:59:11 UTC 2007


I need to prevent kubuntu from loading and connecting the applicable modules 
to my vonage v-phone when I plug it into the usb port. There are NO linux 
client for this phone :(  and it grabs it and interferes with it finding and 
initiaalizing correctly in my vmware-player xp session.

Anybody have an easy way to do this? it is snd_usb_audio, and usb_storage, 
among a few others, however I don't want to just kill those modules as it 
would interfere with my usb stick use on other usb devices.

here is lsusb with the v-phone in.

Bus 005 Device 001: ID 0000:0000
Bus 004 Device 061: ID 0d8c:000c C-Media Electronics, Inc. Audio Adapter
Bus 004 Device 060: ID 058f:9386 Alcor Micro Corp.
Bus 004 Device 059: ID 058f:9254 Alcor Micro Corp. Hub
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 002: ID 413c:8103 Dell Computer Corp. Wireless 350 Bluetooth
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 046d:c505 Logitech, Inc. Cordless Mouse+Keyboard 
Receiver
Bus 001 Device 001: ID 0000:0000


and applicable dmesg:

[17235719.748000] usb 4-2: new full speed USB device using uhci_hcd and 
address 59
[17235719.920000] usb 4-2: configuration #1 chosen from 1 choice
[17235719.920000] hub 4-2:1.0: USB hub found
[17235719.924000] hub 4-2:1.0: 2 ports detected
[17235720.236000] usb 4-2.1: new full speed USB device using uhci_hcd and 
address 60
[17235720.376000] usb 4-2.1: configuration #1 chosen from 1 choice
[17235720.584000] usb 4-2.2: new full speed USB device using uhci_hcd and 
address 61
[17235720.704000] usb 4-2.2: configuration #1 chosen from 1 choice
[17235720.712000] input: C-Media USB Headphone Set   as /class/input/input27
[17235720.712000] input: USB HID v1.00 Device [C-Media USB Headphone Set  ] on 
usb-0000:00:1d.3-2.2
[17235721.360000] usbcore: registered new driver libusual
[17235721.676000] usbcore: registered new driver snd-usb-audio
[17235721.788000] Initializing USB Mass Storage driver...
[17235721.788000] scsi23 : SCSI emulation for USB Mass Storage devices
[17235721.788000] usbcore: registered new driver usb-storage
[17235721.788000] USB Mass Storage support registered.
[17235721.788000] usb-storage: device found at 60
[17235721.788000] usb-storage: waiting for device to settle before scanning
[17235726.788000] usb-storage: device scan complete
[17235726.792000]   Vendor: VONAGE    Model: Flash Disk        Rev: 8.01
[17235726.792000]   Type:   Direct-Access                      ANSI SCSI 
revision: 02
[17235726.792000]   Vendor: Generic   Model:  AUTORUN  Disk    Rev: 8.00
[17235726.792000]   Type:   Direct-Access                      ANSI SCSI 
revision: 02
[17235726.804000] SCSI device sdb: 479157 512-byte hdwr sectors (245 MB)
[17235726.808000] sdb: Write Protect is off
[17235726.808000] sdb: Mode Sense: 03 00 00 00
[17235726.808000] sdb: assuming drive cache: write through
[17235726.820000] SCSI device sdb: 479157 512-byte hdwr sectors (245 MB)
[17235726.824000] sdb: Write Protect is off
[17235726.824000] sdb: Mode Sense: 03 00 00 00
[17235726.824000] sdb: assuming drive cache: write through
[17235726.824000]  sdb: unknown partition table
[17235726.848000] sd 23:0:0:0: Attached scsi removable disk sdb
[17235726.848000] sd 23:0:0:0: Attached scsi generic sg2 type 0
[17235726.856000] SCSI device sdc: 8192 512-byte hdwr sectors (4 MB)
[17235726.860000] sdc: Write Protect is on
[17235726.860000] sdc: Mode Sense: 03 00 80 00
[17235726.860000] sdc: assuming drive cache: write through
[17235726.868000] SCSI device sdc: 8192 512-byte hdwr sectors (4 MB)
[17235726.872000] sdc: Write Protect is on
[17235726.872000] sdc: Mode Sense: 03 00 80 00
[17235726.872000] sdc: assuming drive cache: write through
[17235726.872000]  sdc: sdc1 sdc4
[17235726.880000] sd 23:0:0:1: Attached scsi disk sdc
[17235726.880000] sd 23:0:0:1: Attached scsi generic sg3 type 0
[17235730.124000] FAT: utf8 is not a recommended IO charset for FAT 
filesystems, filesystem will be case sensitive!
[17235730.832000] FAT: utf8 is not a recommended IO charset for FAT 
filesystems, filesystem will be case sensitive!
mike at chiefnb:~$               

Any suggestions appreciated ESPECIALLY one to get this thing to work with 
Linux!!!!!

Mike




More information about the kubuntu-users mailing list