[PATCH] netdev/fec.c: add phylib supporting to enable carrier detection

Greg Ungerer gerg at snapgear.com
Wed Apr 21 05:42:43 UTC 2010


Hi Bryan,

Bryan Wu wrote:
> BugLink: http://bugs.launchpad.net/bugs/457878
> 
>  - removed old MII phy control code
>  - add phylib supporting
>  - add ethtool interface to make user space NetworkManager works
> 
> Tested on Freescale i.MX51 Babbage board.
> 
> This patch is based on a patch from Frederic Rodo <fred.rodo at gmail.com>
> 
> Cc: Frederic Rodo <fred.rodo at gmail.com>
> Signed-off-by: Bryan Wu <bryan.wu at canonical.com>

I tested this on a ColdFire based M5208EVB board (which has internal
FEC interface), and it seemed to work ok. Not all of the PHY's
listed internal to this code are supported by phylib (though I think
most will fall back to generic and be ok).

So I am ok with it:

Acked-by: Greg Ungerer <gerg at uclinux.org>

Regards
Greg



> ---
>  drivers/net/Kconfig |    1 +
>  drivers/net/fec.c   | 1125 ++++++++++++---------------------------------------
>  2 files changed, 253 insertions(+), 873 deletions(-)
> 
> diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
> index 0ba5b8e..41f6a70 100644
> --- a/drivers/net/Kconfig
> +++ b/drivers/net/Kconfig
> @@ -1916,6 +1916,7 @@ config FEC
>  	bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
>  	depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
>  		MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
> +	select PHYLIB
>  	help
>  	  Say Y here if you want to use the built-in 10/100 Fast ethernet
>  	  controller on some Motorola ColdFire and Freescale i.MX processors.
> diff --git a/drivers/net/fec.c b/drivers/net/fec.c
> index 9f98c1c..fca1f66 100644
> --- a/drivers/net/fec.c
> +++ b/drivers/net/fec.c
> @@ -40,6 +40,7 @@
>  #include <linux/irq.h>
>  #include <linux/clk.h>
>  #include <linux/platform_device.h>
> +#include <linux/phy.h>
>  
>  #include <asm/cacheflush.h>
>  
> @@ -61,7 +62,6 @@
>   * Define the fixed address of the FEC hardware.
>   */
>  #if defined(CONFIG_M5272)
> -#define HAVE_mii_link_interrupt
>  
>  static unsigned char	fec_mac_default[] = {
>  	0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> @@ -86,23 +86,6 @@ static unsigned char	fec_mac_default[] = {
>  #endif
>  #endif /* CONFIG_M5272 */
>  
> -/* Forward declarations of some structures to support different PHYs */
> -
> -typedef struct {
> -	uint mii_data;
> -	void (*funct)(uint mii_reg, struct net_device *dev);
> -} phy_cmd_t;
> -
> -typedef struct {
> -	uint id;
> -	char *name;
> -
> -	const phy_cmd_t *config;
> -	const phy_cmd_t *startup;
> -	const phy_cmd_t *ack_int;
> -	const phy_cmd_t *shutdown;
> -} phy_info_t;
> -
>  /* The number of Tx and Rx buffers.  These are allocated from the page
>   * pool.  The code may assume these are power of two, so it it best
>   * to keep them that size.
> @@ -189,29 +172,21 @@ struct fec_enet_private {
>  	uint	tx_full;
>  	/* hold while accessing the HW like ringbuffer for tx/rx but not MAC */
>  	spinlock_t hw_lock;
> -	/* hold while accessing the mii_list_t() elements */
> -	spinlock_t mii_lock;
> -
> -	uint	phy_id;
> -	uint	phy_id_done;
> -	uint	phy_status;
> -	uint	phy_speed;
> -	phy_info_t const	*phy;
> -	struct work_struct phy_task;
>  
> -	uint	sequence_done;
> -	uint	mii_phy_task_queued;
> +	struct  platform_device *pdev;
>  
> -	uint	phy_addr;
> +	int	opened;
>  
> +	/* Phylib and MDIO interface */
> +	struct  mii_bus *mii_bus;
> +	struct  phy_device *phy_dev;
> +	int     mii_timeout;
> +	uint    phy_speed;
>  	int	index;
> -	int	opened;
>  	int	link;
> -	int	old_link;
>  	int	full_duplex;
>  };
>  
> -static void fec_enet_mii(struct net_device *dev);
>  static irqreturn_t fec_enet_interrupt(int irq, void * dev_id);
>  static void fec_enet_tx(struct net_device *dev);
>  static void fec_enet_rx(struct net_device *dev);
> @@ -219,67 +194,20 @@ static int fec_enet_close(struct net_device *dev);
>  static void fec_restart(struct net_device *dev, int duplex);
>  static void fec_stop(struct net_device *dev);
>  
> +/* FEC MII MMFR bits definition */
> +#define FEC_MMFR_ST		(1 << 30)
> +#define FEC_MMFR_OP_READ	(2 << 28)
> +#define FEC_MMFR_OP_WRITE	(1 << 28)
> +#define FEC_MMFR_PA(v)		((v & 0x1f) << 23)
> +#define FEC_MMFR_RA(v)		((v & 0x1f) << 18)
> +#define FEC_MMFR_TA		(2 << 16)
> +#define FEC_MMFR_DATA(v)	(v & 0xffff)
>  
> -/* MII processing.  We keep this as simple as possible.  Requests are
> - * placed on the list (if there is room).  When the request is finished
> - * by the MII, an optional function may be called.
> - */
> -typedef struct mii_list {
> -	uint	mii_regval;
> -	void	(*mii_func)(uint val, struct net_device *dev);
> -	struct	mii_list *mii_next;
> -} mii_list_t;
> -
> -#define		NMII	20
> -static mii_list_t	mii_cmds[NMII];
> -static mii_list_t	*mii_free;
> -static mii_list_t	*mii_head;
> -static mii_list_t	*mii_tail;
> -
> -static int	mii_queue(struct net_device *dev, int request,
> -				void (*func)(uint, struct net_device *));
> -
> -/* Make MII read/write commands for the FEC */
> -#define mk_mii_read(REG)	(0x60020000 | ((REG & 0x1f) << 18))
> -#define mk_mii_write(REG, VAL)	(0x50020000 | ((REG & 0x1f) << 18) | \
> -						(VAL & 0xffff))
> -#define mk_mii_end	0
> +#define FEC_MII_TIMEOUT		10000
>  
>  /* Transmitter timeout */
>  #define TX_TIMEOUT (2 * HZ)
>  
> -/* Register definitions for the PHY */
> -
> -#define MII_REG_CR          0  /* Control Register                         */
> -#define MII_REG_SR          1  /* Status Register                          */
> -#define MII_REG_PHYIR1      2  /* PHY Identification Register 1            */
> -#define MII_REG_PHYIR2      3  /* PHY Identification Register 2            */
> -#define MII_REG_ANAR        4  /* A-N Advertisement Register               */
> -#define MII_REG_ANLPAR      5  /* A-N Link Partner Ability Register        */
> -#define MII_REG_ANER        6  /* A-N Expansion Register                   */
> -#define MII_REG_ANNPTR      7  /* A-N Next Page Transmit Register          */
> -#define MII_REG_ANLPRNPR    8  /* A-N Link Partner Received Next Page Reg. */
> -
> -/* values for phy_status */
> -
> -#define PHY_CONF_ANE	0x0001  /* 1 auto-negotiation enabled */
> -#define PHY_CONF_LOOP	0x0002  /* 1 loopback mode enabled */
> -#define PHY_CONF_SPMASK	0x00f0  /* mask for speed */
> -#define PHY_CONF_10HDX	0x0010  /* 10 Mbit half duplex supported */
> -#define PHY_CONF_10FDX	0x0020  /* 10 Mbit full duplex supported */
> -#define PHY_CONF_100HDX	0x0040  /* 100 Mbit half duplex supported */
> -#define PHY_CONF_100FDX	0x0080  /* 100 Mbit full duplex supported */
> -
> -#define PHY_STAT_LINK	0x0100  /* 1 up - 0 down */
> -#define PHY_STAT_FAULT	0x0200  /* 1 remote fault */
> -#define PHY_STAT_ANC	0x0400  /* 1 auto-negotiation complete	*/
> -#define PHY_STAT_SPMASK	0xf000  /* mask for speed */
> -#define PHY_STAT_10HDX	0x1000  /* 10 Mbit half duplex selected	*/
> -#define PHY_STAT_10FDX	0x2000  /* 10 Mbit full duplex selected	*/
> -#define PHY_STAT_100HDX	0x4000  /* 100 Mbit half duplex selected */
> -#define PHY_STAT_100FDX	0x8000  /* 100 Mbit full duplex selected */
> -
> -
>  static int
>  fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
>  {
> @@ -406,12 +334,6 @@ fec_enet_interrupt(int irq, void * dev_id)
>  			ret = IRQ_HANDLED;
>  			fec_enet_tx(dev);
>  		}
> -
> -		if (int_events & FEC_ENET_MII) {
> -			ret = IRQ_HANDLED;
> -			fec_enet_mii(dev);
> -		}
> -
>  	} while (int_events);
>  
>  	return ret;
> @@ -607,827 +529,312 @@ rx_processing_done:
>  	spin_unlock(&fep->hw_lock);
>  }
>  
> -/* called from interrupt context */
> -static void
> -fec_enet_mii(struct net_device *dev)
> -{
> -	struct	fec_enet_private *fep;
> -	mii_list_t	*mip;
> -
> -	fep = netdev_priv(dev);
> -	spin_lock(&fep->mii_lock);
> -
> -	if ((mip = mii_head) == NULL) {
> -		printk("MII and no head!\n");
> -		goto unlock;
> -	}
> -
> -	if (mip->mii_func != NULL)
> -		(*(mip->mii_func))(readl(fep->hwp + FEC_MII_DATA), dev);
> -
> -	mii_head = mip->mii_next;
> -	mip->mii_next = mii_free;
> -	mii_free = mip;
> -
> -	if ((mip = mii_head) != NULL)
> -		writel(mip->mii_regval, fep->hwp + FEC_MII_DATA);
> -
> -unlock:
> -	spin_unlock(&fep->mii_lock);
> -}
> -
> -static int
> -mii_queue_unlocked(struct net_device *dev, int regval,
> -		void (*func)(uint, struct net_device *))
> +/* ------------------------------------------------------------------------- */
> +#ifdef CONFIG_M5272
> +static void __inline__ fec_get_mac(struct net_device *dev)
>  {
> -	struct fec_enet_private *fep;
> -	mii_list_t	*mip;
> -	int		retval;
> -
> -	/* Add PHY address to register command */
> -	fep = netdev_priv(dev);
> +	struct fec_enet_private *fep = netdev_priv(dev);
> +	unsigned char *iap, tmpaddr[ETH_ALEN];
>  
> -	regval |= fep->phy_addr << 23;
> -	retval = 0;
> -
> -	if ((mip = mii_free) != NULL) {
> -		mii_free = mip->mii_next;
> -		mip->mii_regval = regval;
> -		mip->mii_func = func;
> -		mip->mii_next = NULL;
> -		if (mii_head) {
> -			mii_tail->mii_next = mip;
> -			mii_tail = mip;
> -		} else {
> -			mii_head = mii_tail = mip;
> -			writel(regval, fep->hwp + FEC_MII_DATA);
> -		}
> +	if (FEC_FLASHMAC) {
> +		/*
> +		 * Get MAC address from FLASH.
> +		 * If it is all 1's or 0's, use the default.
> +		 */
> +		iap = (unsigned char *)FEC_FLASHMAC;
> +		if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
> +		    (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
> +			iap = fec_mac_default;
> +		if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
> +		    (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
> +			iap = fec_mac_default;
>  	} else {
> -		retval = 1;
> +		*((unsigned long *) &tmpaddr[0]) = readl(fep->hwp + FEC_ADDR_LOW);
> +		*((unsigned short *) &tmpaddr[4]) = (readl(fep->hwp + FEC_ADDR_HIGH) >> 16);
> +		iap = &tmpaddr[0];
>  	}
>  
> -	return retval;
> -}
> -
> -static int
> -mii_queue(struct net_device *dev, int regval,
> -		void (*func)(uint, struct net_device *))
> -{
> -	struct fec_enet_private *fep;
> -	unsigned long   flags;
> -	int             retval;
> -	fep = netdev_priv(dev);
> -	spin_lock_irqsave(&fep->mii_lock, flags);
> -	retval = mii_queue_unlocked(dev, regval, func);
> -	spin_unlock_irqrestore(&fep->mii_lock, flags);
> -	return retval;
> -}
> -
> -static void mii_do_cmd(struct net_device *dev, const phy_cmd_t *c)
> -{
> -	if(!c)
> -		return;
> +	memcpy(dev->dev_addr, iap, ETH_ALEN);
>  
> -	for (; c->mii_data != mk_mii_end; c++)
> -		mii_queue(dev, c->mii_data, c->funct);
> +	/* Adjust MAC if using default MAC address */
> +	if (iap == fec_mac_default)
> +		 dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
>  }
> +#endif
>  
> -static void mii_parse_sr(uint mii_reg, struct net_device *dev)
> -{
> -	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -	uint status;
> -
> -	status = *s & ~(PHY_STAT_LINK | PHY_STAT_FAULT | PHY_STAT_ANC);
> -
> -	if (mii_reg & 0x0004)
> -		status |= PHY_STAT_LINK;
> -	if (mii_reg & 0x0010)
> -		status |= PHY_STAT_FAULT;
> -	if (mii_reg & 0x0020)
> -		status |= PHY_STAT_ANC;
> -	*s = status;
> -}
> +/* ------------------------------------------------------------------------- */
>  
> -static void mii_parse_cr(uint mii_reg, struct net_device *dev)
> +/*
> + * Phy section
> + */
> +static void fec_enet_adjust_link(struct net_device *dev)
>  {
>  	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -	uint status;
> -
> -	status = *s & ~(PHY_CONF_ANE | PHY_CONF_LOOP);
> -
> -	if (mii_reg & 0x1000)
> -		status |= PHY_CONF_ANE;
> -	if (mii_reg & 0x4000)
> -		status |= PHY_CONF_LOOP;
> -	*s = status;
> -}
> +	struct phy_device *phy_dev = fep->phy_dev;
> +	unsigned long flags;
>  
> -static void mii_parse_anar(uint mii_reg, struct net_device *dev)
> -{
> -	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -	uint status;
> -
> -	status = *s & ~(PHY_CONF_SPMASK);
> -
> -	if (mii_reg & 0x0020)
> -		status |= PHY_CONF_10HDX;
> -	if (mii_reg & 0x0040)
> -		status |= PHY_CONF_10FDX;
> -	if (mii_reg & 0x0080)
> -		status |= PHY_CONF_100HDX;
> -	if (mii_reg & 0x00100)
> -		status |= PHY_CONF_100FDX;
> -	*s = status;
> -}
> +	int status_change = 0;
>  
> -/* ------------------------------------------------------------------------- */
> -/* The Level one LXT970 is used by many boards				     */
> +	spin_lock_irqsave(&fep->hw_lock, flags);
>  
> -#define MII_LXT970_MIRROR    16  /* Mirror register           */
> -#define MII_LXT970_IER       17  /* Interrupt Enable Register */
> -#define MII_LXT970_ISR       18  /* Interrupt Status Register */
> -#define MII_LXT970_CONFIG    19  /* Configuration Register    */
> -#define MII_LXT970_CSR       20  /* Chip Status Register      */
> +	/* Prevent a state halted on mii error */
> +	if (fep->mii_timeout && phy_dev->state == PHY_HALTED) {
> +		phy_dev->state = PHY_RESUMING;
> +		goto spin_unlock;
> +	}
>  
> -static void mii_parse_lxt970_csr(uint mii_reg, struct net_device *dev)
> -{
> -	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -	uint status;
> +	/* Duplex link change */
> +	if (phy_dev->link) {
> +		if (fep->full_duplex != phy_dev->duplex) {
> +			fec_restart(dev, phy_dev->duplex);
> +			status_change = 1;
> +		}
> +	}
>  
> -	status = *s & ~(PHY_STAT_SPMASK);
> -	if (mii_reg & 0x0800) {
> -		if (mii_reg & 0x1000)
> -			status |= PHY_STAT_100FDX;
> +	/* Link on or off change */
> +	if (phy_dev->link != fep->link) {
> +		fep->link = phy_dev->link;
> +		if (phy_dev->link)
> +			fec_restart(dev, phy_dev->duplex);
>  		else
> -			status |= PHY_STAT_100HDX;
> -	} else {
> -		if (mii_reg & 0x1000)
> -			status |= PHY_STAT_10FDX;
> -		else
> -			status |= PHY_STAT_10HDX;
> +			fec_stop(dev);
> +		status_change = 1;
>  	}
> -	*s = status;
> -}
> -
> -static phy_cmd_t const phy_cmd_lxt970_config[] = {
> -		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
> -		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_lxt970_startup[] = { /* enable interrupts */
> -		{ mk_mii_write(MII_LXT970_IER, 0x0002), NULL },
> -		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_lxt970_ack_int[] = {
> -		/* read SR and ISR to acknowledge */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_read(MII_LXT970_ISR), NULL },
> -
> -		/* find out the current status */
> -		{ mk_mii_read(MII_LXT970_CSR), mii_parse_lxt970_csr },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_lxt970_shutdown[] = { /* disable interrupts */
> -		{ mk_mii_write(MII_LXT970_IER, 0x0000), NULL },
> -		{ mk_mii_end, }
> -	};
> -static phy_info_t const phy_info_lxt970 = {
> -	.id = 0x07810000,
> -	.name = "LXT970",
> -	.config = phy_cmd_lxt970_config,
> -	.startup = phy_cmd_lxt970_startup,
> -	.ack_int = phy_cmd_lxt970_ack_int,
> -	.shutdown = phy_cmd_lxt970_shutdown
> -};
>  
> -/* ------------------------------------------------------------------------- */
> -/* The Level one LXT971 is used on some of my custom boards                  */
> -
> -/* register definitions for the 971 */
> +spin_unlock:
> +	spin_unlock_irqrestore(&fep->hw_lock, flags);
>  
> -#define MII_LXT971_PCR       16  /* Port Control Register     */
> -#define MII_LXT971_SR2       17  /* Status Register 2         */
> -#define MII_LXT971_IER       18  /* Interrupt Enable Register */
> -#define MII_LXT971_ISR       19  /* Interrupt Status Register */
> -#define MII_LXT971_LCR       20  /* LED Control Register      */
> -#define MII_LXT971_TCR       30  /* Transmit Control Register */
> +	if (status_change)
> +		phy_print_status(phy_dev);
> +}
>  
>  /*
> - * I had some nice ideas of running the MDIO faster...
> - * The 971 should support 8MHz and I tried it, but things acted really
> - * weird, so 2.5 MHz ought to be enough for anyone...
> + * NOTE: a MII transaction is during around 25 us, so polling it...
>   */
> -
> -static void mii_parse_lxt971_sr2(uint mii_reg, struct net_device *dev)
> +static int fec_enet_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
>  {
> -	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -	uint status;
> +	struct fec_enet_private *fep = bus->priv;
> +	int timeout = FEC_MII_TIMEOUT;
>  
> -	status = *s & ~(PHY_STAT_SPMASK | PHY_STAT_LINK | PHY_STAT_ANC);
> +	fep->mii_timeout = 0;
>  
> -	if (mii_reg & 0x0400) {
> -		fep->link = 1;
> -		status |= PHY_STAT_LINK;
> -	} else {
> -		fep->link = 0;
> -	}
> -	if (mii_reg & 0x0080)
> -		status |= PHY_STAT_ANC;
> -	if (mii_reg & 0x4000) {
> -		if (mii_reg & 0x0200)
> -			status |= PHY_STAT_100FDX;
> -		else
> -			status |= PHY_STAT_100HDX;
> -	} else {
> -		if (mii_reg & 0x0200)
> -			status |= PHY_STAT_10FDX;
> -		else
> -			status |= PHY_STAT_10HDX;
> +	/* clear MII end of transfer bit*/
> +	writel(FEC_ENET_MII, fep->hwp + FEC_IEVENT);
> +
> +	/* start a read op */
> +	writel(FEC_MMFR_ST | FEC_MMFR_OP_READ |
> +		FEC_MMFR_PA(mii_id) | FEC_MMFR_RA(regnum) |
> +		FEC_MMFR_TA, fep->hwp + FEC_MII_DATA);
> +
> +	/* wait for end of transfer */
> +	while (!(readl(fep->hwp + FEC_IEVENT) & FEC_ENET_MII)) {
> +		cpu_relax();
> +		if (timeout-- < 0) {
> +			fep->mii_timeout = 1;
> +			printk(KERN_ERR "FEC: MDIO read timeout\n");
> +			return -ETIMEDOUT;
> +		}
>  	}
> -	if (mii_reg & 0x0008)
> -		status |= PHY_STAT_FAULT;
>  
> -	*s = status;
> +	/* return value */
> +	return FEC_MMFR_DATA(readl(fep->hwp + FEC_MII_DATA));
>  }
>  
> -static phy_cmd_t const phy_cmd_lxt971_config[] = {
> -		/* limit to 10MBit because my prototype board
> -		 * doesn't work with 100. */
> -		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
> -		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
> -		{ mk_mii_read(MII_LXT971_SR2), mii_parse_lxt971_sr2 },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_lxt971_startup[] = {  /* enable interrupts */
> -		{ mk_mii_write(MII_LXT971_IER, 0x00f2), NULL },
> -		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
> -		{ mk_mii_write(MII_LXT971_LCR, 0xd422), NULL }, /* LED config */
> -		/* Somehow does the 971 tell me that the link is down
> -		 * the first read after power-up.
> -		 * read here to get a valid value in ack_int */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_lxt971_ack_int[] = {
> -		/* acknowledge the int before reading status ! */
> -		{ mk_mii_read(MII_LXT971_ISR), NULL },
> -		/* find out the current status */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_read(MII_LXT971_SR2), mii_parse_lxt971_sr2 },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_lxt971_shutdown[] = { /* disable interrupts */
> -		{ mk_mii_write(MII_LXT971_IER, 0x0000), NULL },
> -		{ mk_mii_end, }
> -	};
> -static phy_info_t const phy_info_lxt971 = {
> -	.id = 0x0001378e,
> -	.name = "LXT971",
> -	.config = phy_cmd_lxt971_config,
> -	.startup = phy_cmd_lxt971_startup,
> -	.ack_int = phy_cmd_lxt971_ack_int,
> -	.shutdown = phy_cmd_lxt971_shutdown
> -};
> -
> -/* ------------------------------------------------------------------------- */
> -/* The Quality Semiconductor QS6612 is used on the RPX CLLF                  */
> -
> -/* register definitions */
> -
> -#define MII_QS6612_MCR       17  /* Mode Control Register      */
> -#define MII_QS6612_FTR       27  /* Factory Test Register      */
> -#define MII_QS6612_MCO       28  /* Misc. Control Register     */
> -#define MII_QS6612_ISR       29  /* Interrupt Source Register  */
> -#define MII_QS6612_IMR       30  /* Interrupt Mask Register    */
> -#define MII_QS6612_PCR       31  /* 100BaseTx PHY Control Reg. */
> -
> -static void mii_parse_qs6612_pcr(uint mii_reg, struct net_device *dev)
> +static int fec_enet_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
> +			   u16 value)
>  {
> -	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -	uint status;
> +	struct fec_enet_private *fep = bus->priv;
> +	int timeout = FEC_MII_TIMEOUT;
>  
> -	status = *s & ~(PHY_STAT_SPMASK);
> +	fep->mii_timeout = 0;
>  
> -	switch((mii_reg >> 2) & 7) {
> -	case 1: status |= PHY_STAT_10HDX; break;
> -	case 2: status |= PHY_STAT_100HDX; break;
> -	case 5: status |= PHY_STAT_10FDX; break;
> -	case 6: status |= PHY_STAT_100FDX; break;
> -}
> -
> -	*s = status;
> -}
> -
> -static phy_cmd_t const phy_cmd_qs6612_config[] = {
> -		/* The PHY powers up isolated on the RPX,
> -		 * so send a command to allow operation.
> -		 */
> -		{ mk_mii_write(MII_QS6612_PCR, 0x0dc0), NULL },
> -
> -		/* parse cr and anar to get some info */
> -		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
> -		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_qs6612_startup[] = {  /* enable interrupts */
> -		{ mk_mii_write(MII_QS6612_IMR, 0x003a), NULL },
> -		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_qs6612_ack_int[] = {
> -		/* we need to read ISR, SR and ANER to acknowledge */
> -		{ mk_mii_read(MII_QS6612_ISR), NULL },
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_read(MII_REG_ANER), NULL },
> -
> -		/* read pcr to get info */
> -		{ mk_mii_read(MII_QS6612_PCR), mii_parse_qs6612_pcr },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_qs6612_shutdown[] = { /* disable interrupts */
> -		{ mk_mii_write(MII_QS6612_IMR, 0x0000), NULL },
> -		{ mk_mii_end, }
> -	};
> -static phy_info_t const phy_info_qs6612 = {
> -	.id = 0x00181440,
> -	.name = "QS6612",
> -	.config = phy_cmd_qs6612_config,
> -	.startup = phy_cmd_qs6612_startup,
> -	.ack_int = phy_cmd_qs6612_ack_int,
> -	.shutdown = phy_cmd_qs6612_shutdown
> -};
> -
> -/* ------------------------------------------------------------------------- */
> -/* AMD AM79C874 phy                                                          */
> +	/* clear MII end of transfer bit*/
> +	writel(FEC_ENET_MII, fep->hwp + FEC_IEVENT);
>  
> -/* register definitions for the 874 */
> +	/* start a read op */
> +	writel(FEC_MMFR_ST | FEC_MMFR_OP_READ |
> +		FEC_MMFR_PA(mii_id) | FEC_MMFR_RA(regnum) |
> +		FEC_MMFR_TA | FEC_MMFR_DATA(value),
> +		fep->hwp + FEC_MII_DATA);
> +
> +	/* wait for end of transfer */
> +	while (!(readl(fep->hwp + FEC_IEVENT) & FEC_ENET_MII)) {
> +		cpu_relax();
> +		if (timeout-- < 0) {
> +			fep->mii_timeout = 1;
> +			printk(KERN_ERR "FEC: MDIO write timeout\n");
> +			return -ETIMEDOUT;
> +		}
> +	}
>  
> -#define MII_AM79C874_MFR       16  /* Miscellaneous Feature Register */
> -#define MII_AM79C874_ICSR      17  /* Interrupt/Status Register      */
> -#define MII_AM79C874_DR        18  /* Diagnostic Register            */
> -#define MII_AM79C874_PMLR      19  /* Power and Loopback Register    */
> -#define MII_AM79C874_MCR       21  /* ModeControl Register           */
> -#define MII_AM79C874_DC        23  /* Disconnect Counter             */
> -#define MII_AM79C874_REC       24  /* Recieve Error Counter          */
> +	return 0;
> +}
>  
> -static void mii_parse_am79c874_dr(uint mii_reg, struct net_device *dev)
> +static int fec_enet_mdio_reset(struct mii_bus *bus)
>  {
> -	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -	uint status;
> -
> -	status = *s & ~(PHY_STAT_SPMASK | PHY_STAT_ANC);
> -
> -	if (mii_reg & 0x0080)
> -		status |= PHY_STAT_ANC;
> -	if (mii_reg & 0x0400)
> -		status |= ((mii_reg & 0x0800) ? PHY_STAT_100FDX : PHY_STAT_100HDX);
> -	else
> -		status |= ((mii_reg & 0x0800) ? PHY_STAT_10FDX : PHY_STAT_10HDX);
> -
> -	*s = status;
> +	return 0;
>  }
>  
> -static phy_cmd_t const phy_cmd_am79c874_config[] = {
> -		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
> -		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
> -		{ mk_mii_read(MII_AM79C874_DR), mii_parse_am79c874_dr },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_am79c874_startup[] = {  /* enable interrupts */
> -		{ mk_mii_write(MII_AM79C874_ICSR, 0xff00), NULL },
> -		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_am79c874_ack_int[] = {
> -		/* find out the current status */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_read(MII_AM79C874_DR), mii_parse_am79c874_dr },
> -		/* we only need to read ISR to acknowledge */
> -		{ mk_mii_read(MII_AM79C874_ICSR), NULL },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_am79c874_shutdown[] = { /* disable interrupts */
> -		{ mk_mii_write(MII_AM79C874_ICSR, 0x0000), NULL },
> -		{ mk_mii_end, }
> -	};
> -static phy_info_t const phy_info_am79c874 = {
> -	.id = 0x00022561,
> -	.name = "AM79C874",
> -	.config = phy_cmd_am79c874_config,
> -	.startup = phy_cmd_am79c874_startup,
> -	.ack_int = phy_cmd_am79c874_ack_int,
> -	.shutdown = phy_cmd_am79c874_shutdown
> -};
> -
> -
> -/* ------------------------------------------------------------------------- */
> -/* Kendin KS8721BL phy                                                       */
> -
> -/* register definitions for the 8721 */
> -
> -#define MII_KS8721BL_RXERCR	21
> -#define MII_KS8721BL_ICSR	27
> -#define	MII_KS8721BL_PHYCR	31
> -
> -static phy_cmd_t const phy_cmd_ks8721bl_config[] = {
> -		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
> -		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_ks8721bl_startup[] = {  /* enable interrupts */
> -		{ mk_mii_write(MII_KS8721BL_ICSR, 0xff00), NULL },
> -		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_ks8721bl_ack_int[] = {
> -		/* find out the current status */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		/* we only need to read ISR to acknowledge */
> -		{ mk_mii_read(MII_KS8721BL_ICSR), NULL },
> -		{ mk_mii_end, }
> -	};
> -static phy_cmd_t const phy_cmd_ks8721bl_shutdown[] = { /* disable interrupts */
> -		{ mk_mii_write(MII_KS8721BL_ICSR, 0x0000), NULL },
> -		{ mk_mii_end, }
> -	};
> -static phy_info_t const phy_info_ks8721bl = {
> -	.id = 0x00022161,
> -	.name = "KS8721BL",
> -	.config = phy_cmd_ks8721bl_config,
> -	.startup = phy_cmd_ks8721bl_startup,
> -	.ack_int = phy_cmd_ks8721bl_ack_int,
> -	.shutdown = phy_cmd_ks8721bl_shutdown
> -};
> -
> -/* ------------------------------------------------------------------------- */
> -/* register definitions for the DP83848 */
> -
> -#define MII_DP8384X_PHYSTST    16  /* PHY Status Register */
> -
> -static void mii_parse_dp8384x_sr2(uint mii_reg, struct net_device *dev)
> +static int fec_enet_mii_probe(struct net_device *dev)
>  {
>  	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> -
> -	*s &= ~(PHY_STAT_SPMASK | PHY_STAT_LINK | PHY_STAT_ANC);
> -
> -	/* Link up */
> -	if (mii_reg & 0x0001) {
> -		fep->link = 1;
> -		*s |= PHY_STAT_LINK;
> -	} else
> -		fep->link = 0;
> -	/* Status of link */
> -	if (mii_reg & 0x0010)   /* Autonegotioation complete */
> -		*s |= PHY_STAT_ANC;
> -	if (mii_reg & 0x0002) {   /* 10MBps? */
> -		if (mii_reg & 0x0004)   /* Full Duplex? */
> -			*s |= PHY_STAT_10FDX;
> -		else
> -			*s |= PHY_STAT_10HDX;
> -	} else {                  /* 100 Mbps? */
> -		if (mii_reg & 0x0004)   /* Full Duplex? */
> -			*s |= PHY_STAT_100FDX;
> -		else
> -			*s |= PHY_STAT_100HDX;
> -	}
> -	if (mii_reg & 0x0008)
> -		*s |= PHY_STAT_FAULT;
> -}
> -
> -static phy_info_t phy_info_dp83848= {
> -	0x020005c9,
> -	"DP83848",
> +	struct phy_device *phy_dev = NULL;
> +	int phy_addr;
>  
> -	(const phy_cmd_t []) {  /* config */
> -		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
> -		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
> -		{ mk_mii_read(MII_DP8384X_PHYSTST), mii_parse_dp8384x_sr2 },
> -		{ mk_mii_end, }
> -	},
> -	(const phy_cmd_t []) {  /* startup - enable interrupts */
> -		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_end, }
> -	},
> -	(const phy_cmd_t []) { /* ack_int - never happens, no interrupt */
> -		{ mk_mii_end, }
> -	},
> -	(const phy_cmd_t []) {  /* shutdown */
> -		{ mk_mii_end, }
> -	},
> -};
> +	/* find the first phy */
> +	for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) {
> +		if (fep->mii_bus->phy_map[phy_addr]) {
> +			phy_dev = fep->mii_bus->phy_map[phy_addr];
> +			break;
> +		}
> +	}
>  
> -static phy_info_t phy_info_lan8700 = {
> -	0x0007C0C,
> -	"LAN8700",
> -	(const phy_cmd_t []) { /* config */
> -		{ mk_mii_read(MII_REG_CR), mii_parse_cr },
> -		{ mk_mii_read(MII_REG_ANAR), mii_parse_anar },
> -		{ mk_mii_end, }
> -	},
> -	(const phy_cmd_t []) { /* startup */
> -		{ mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
> -		{ mk_mii_read(MII_REG_SR), mii_parse_sr },
> -		{ mk_mii_end, }
> -	},
> -	(const phy_cmd_t []) { /* act_int */
> -		{ mk_mii_end, }
> -	},
> -	(const phy_cmd_t []) { /* shutdown */
> -		{ mk_mii_end, }
> -	},
> -};
> -/* ------------------------------------------------------------------------- */
> +	if (!phy_dev) {
> +		printk(KERN_ERR "%s: no PHY found\n", dev->name);
> +		return -ENODEV;
> +	}
>  
> -static phy_info_t const * const phy_info[] = {
> -	&phy_info_lxt970,
> -	&phy_info_lxt971,
> -	&phy_info_qs6612,
> -	&phy_info_am79c874,
> -	&phy_info_ks8721bl,
> -	&phy_info_dp83848,
> -	&phy_info_lan8700,
> -	NULL
> -};
> +	/* attach the mac to the phy */
> +	phy_dev = phy_connect(dev, dev_name(&phy_dev->dev),
> +			     &fec_enet_adjust_link, 0,
> +			     PHY_INTERFACE_MODE_MII);
> +	if (IS_ERR(phy_dev)) {
> +		printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
> +		return PTR_ERR(phy_dev);
> +	}
>  
> -/* ------------------------------------------------------------------------- */
> -#ifdef HAVE_mii_link_interrupt
> -static irqreturn_t
> -mii_link_interrupt(int irq, void * dev_id);
> +	/* mask with MAC supported features */
> +	phy_dev->supported &= PHY_BASIC_FEATURES;
> +	phy_dev->advertising = phy_dev->supported;
>  
> -/*
> - *	This is specific to the MII interrupt setup of the M5272EVB.
> - */
> -static void __inline__ fec_request_mii_intr(struct net_device *dev)
> -{
> -	if (request_irq(66, mii_link_interrupt, IRQF_DISABLED, "fec(MII)", dev) != 0)
> -		printk("FEC: Could not allocate fec(MII) IRQ(66)!\n");
> -}
> +	fep->phy_dev = phy_dev;
> +	fep->link = 0;
> +	fep->full_duplex = 0;
>  
> -static void __inline__ fec_disable_phy_intr(struct net_device *dev)
> -{
> -	free_irq(66, dev);
> +	return 0;
>  }
> -#endif
>  
> -#ifdef CONFIG_M5272
> -static void __inline__ fec_get_mac(struct net_device *dev)
> +static int fec_enet_mii_init(struct platform_device *pdev)
>  {
> +	struct net_device *dev = platform_get_drvdata(pdev);
>  	struct fec_enet_private *fep = netdev_priv(dev);
> -	unsigned char *iap, tmpaddr[ETH_ALEN];
> +	int err = -ENXIO, i;
>  
> -	if (FEC_FLASHMAC) {
> -		/*
> -		 * Get MAC address from FLASH.
> -		 * If it is all 1's or 0's, use the default.
> -		 */
> -		iap = (unsigned char *)FEC_FLASHMAC;
> -		if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
> -		    (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
> -			iap = fec_mac_default;
> -		if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
> -		    (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
> -			iap = fec_mac_default;
> -	} else {
> -		*((unsigned long *) &tmpaddr[0]) = readl(fep->hwp + FEC_ADDR_LOW);
> -		*((unsigned short *) &tmpaddr[4]) = (readl(fep->hwp + FEC_ADDR_HIGH) >> 16);
> -		iap = &tmpaddr[0];
> -	}
> -
> -	memcpy(dev->dev_addr, iap, ETH_ALEN);
> -
> -	/* Adjust MAC if using default MAC address */
> -	if (iap == fec_mac_default)
> -		 dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
> -}
> -#endif
> +	fep->mii_timeout = 0;
>  
> -/* ------------------------------------------------------------------------- */
> -
> -static void mii_display_status(struct net_device *dev)
> -{
> -	struct fec_enet_private *fep = netdev_priv(dev);
> -	volatile uint *s = &(fep->phy_status);
> +	/*
> +	 * Set MII speed to 2.5 MHz
> +	 */
> +	fep->phy_speed = ((((clk_get_rate(fep->clk) / 2 + 4999999)
> +					/ 2500000) / 2) & 0x3F) << 1;
> +	writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
>  
> -	if (!fep->link && !fep->old_link) {
> -		/* Link is still down - don't print anything */
> -		return;
> +	fep->mii_bus = mdiobus_alloc();
> +	if (fep->mii_bus == NULL) {
> +		err = -ENOMEM;
> +		goto err_out;
>  	}
>  
> -	printk("%s: status: ", dev->name);
> -
> -	if (!fep->link) {
> -		printk("link down");
> -	} else {
> -		printk("link up");
> -
> -		switch(*s & PHY_STAT_SPMASK) {
> -		case PHY_STAT_100FDX: printk(", 100MBit Full Duplex"); break;
> -		case PHY_STAT_100HDX: printk(", 100MBit Half Duplex"); break;
> -		case PHY_STAT_10FDX: printk(", 10MBit Full Duplex"); break;
> -		case PHY_STAT_10HDX: printk(", 10MBit Half Duplex"); break;
> -		default:
> -			printk(", Unknown speed/duplex");
> -		}
> -
> -		if (*s & PHY_STAT_ANC)
> -			printk(", auto-negotiation complete");
> +	fep->mii_bus->name = "fec_enet_mii_bus";
> +	fep->mii_bus->read = fec_enet_mdio_read;
> +	fep->mii_bus->write = fec_enet_mdio_write;
> +	fep->mii_bus->reset = fec_enet_mdio_reset;
> +	snprintf(fep->mii_bus->id, MII_BUS_ID_SIZE, "%x", pdev->id);
> +	fep->mii_bus->priv = fep;
> +	fep->mii_bus->parent = &pdev->dev;
> +
> +	fep->mii_bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
> +	if (!fep->mii_bus->irq) {
> +		err = -ENOMEM;
> +		goto err_out_free_mdiobus;
>  	}
>  
> -	if (*s & PHY_STAT_FAULT)
> -		printk(", remote fault");
> -
> -	printk(".\n");
> -}
> -
> -static void mii_display_config(struct work_struct *work)
> -{
> -	struct fec_enet_private *fep = container_of(work, struct fec_enet_private, phy_task);
> -	struct net_device *dev = fep->netdev;
> -	uint status = fep->phy_status;
> +	for (i = 0; i < PHY_MAX_ADDR; i++)
> +		fep->mii_bus->irq[i] = PHY_POLL;
>  
> -	/*
> -	** When we get here, phy_task is already removed from
> -	** the workqueue.  It is thus safe to allow to reuse it.
> -	*/
> -	fep->mii_phy_task_queued = 0;
> -	printk("%s: config: auto-negotiation ", dev->name);
> -
> -	if (status & PHY_CONF_ANE)
> -		printk("on");
> -	else
> -		printk("off");
> +	platform_set_drvdata(dev, fep->mii_bus);
>  
> -	if (status & PHY_CONF_100FDX)
> -		printk(", 100FDX");
> -	if (status & PHY_CONF_100HDX)
> -		printk(", 100HDX");
> -	if (status & PHY_CONF_10FDX)
> -		printk(", 10FDX");
> -	if (status & PHY_CONF_10HDX)
> -		printk(", 10HDX");
> -	if (!(status & PHY_CONF_SPMASK))
> -		printk(", No speed/duplex selected?");
> +	if (mdiobus_register(fep->mii_bus))
> +		goto err_out_free_mdio_irq;
>  
> -	if (status & PHY_CONF_LOOP)
> -		printk(", loopback enabled");
> +	if (fec_enet_mii_probe(dev) != 0)
> +		goto err_out_unregister_bus;
>  
> -	printk(".\n");
> +	return 0;
>  
> -	fep->sequence_done = 1;
> +err_out_unregister_bus:
> +	mdiobus_unregister(fep->mii_bus);
> +err_out_free_mdio_irq:
> +	kfree(fep->mii_bus->irq);
> +err_out_free_mdiobus:
> +	mdiobus_free(fep->mii_bus);
> +err_out:
> +	return err;
>  }
>  
> -static void mii_relink(struct work_struct *work)
> +static void fec_enet_mii_remove(struct fec_enet_private *fep)
>  {
> -	struct fec_enet_private *fep = container_of(work, struct fec_enet_private, phy_task);
> -	struct net_device *dev = fep->netdev;
> -	int duplex;
> -
> -	/*
> -	** When we get here, phy_task is already removed from
> -	** the workqueue.  It is thus safe to allow to reuse it.
> -	*/
> -	fep->mii_phy_task_queued = 0;
> -	fep->link = (fep->phy_status & PHY_STAT_LINK) ? 1 : 0;
> -	mii_display_status(dev);
> -	fep->old_link = fep->link;
> -
> -	if (fep->link) {
> -		duplex = 0;
> -		if (fep->phy_status
> -		    & (PHY_STAT_100FDX | PHY_STAT_10FDX))
> -			duplex = 1;
> -		fec_restart(dev, duplex);
> -	} else
> -		fec_stop(dev);
> +	if (fep->phy_dev)
> +		phy_disconnect(fep->phy_dev);
> +	mdiobus_unregister(fep->mii_bus);
> +	kfree(fep->mii_bus->irq);
> +	mdiobus_free(fep->mii_bus);
>  }
>  
> -/* mii_queue_relink is called in interrupt context from mii_link_interrupt */
> -static void mii_queue_relink(uint mii_reg, struct net_device *dev)
> +static int fec_enet_get_settings(struct net_device *dev,
> +				  struct ethtool_cmd *cmd)
>  {
>  	struct fec_enet_private *fep = netdev_priv(dev);
> +	struct phy_device *phydev = fep->phy_dev;
>  
> -	/*
> -	 * We cannot queue phy_task twice in the workqueue.  It
> -	 * would cause an endless loop in the workqueue.
> -	 * Fortunately, if the last mii_relink entry has not yet been
> -	 * executed now, it will do the job for the current interrupt,
> -	 * which is just what we want.
> -	 */
> -	if (fep->mii_phy_task_queued)
> -		return;
> +	if (!phydev)
> +		return -ENODEV;
>  
> -	fep->mii_phy_task_queued = 1;
> -	INIT_WORK(&fep->phy_task, mii_relink);
> -	schedule_work(&fep->phy_task);
> +	return phy_ethtool_gset(phydev, cmd);
>  }
>  
> -/* mii_queue_config is called in interrupt context from fec_enet_mii */
> -static void mii_queue_config(uint mii_reg, struct net_device *dev)
> +static int fec_enet_set_settings(struct net_device *dev,
> +				 struct ethtool_cmd *cmd)
>  {
>  	struct fec_enet_private *fep = netdev_priv(dev);
> +	struct phy_device *phydev = fep->phy_dev;
>  
> -	if (fep->mii_phy_task_queued)
> -		return;
> +	if (!phydev)
> +		return -ENODEV;
>  
> -	fep->mii_phy_task_queued = 1;
> -	INIT_WORK(&fep->phy_task, mii_display_config);
> -	schedule_work(&fep->phy_task);
> +	return phy_ethtool_sset(phydev, cmd);
>  }
>  
> -phy_cmd_t const phy_cmd_relink[] = {
> -	{ mk_mii_read(MII_REG_CR), mii_queue_relink },
> -	{ mk_mii_end, }
> -	};
> -phy_cmd_t const phy_cmd_config[] = {
> -	{ mk_mii_read(MII_REG_CR), mii_queue_config },
> -	{ mk_mii_end, }
> -	};
> -
> -/* Read remainder of PHY ID. */
> -static void
> -mii_discover_phy3(uint mii_reg, struct net_device *dev)
> +static void fec_enet_get_drvinfo(struct net_device *dev,
> +				 struct ethtool_drvinfo *info)
>  {
> -	struct fec_enet_private *fep;
> -	int i;
> -
> -	fep = netdev_priv(dev);
> -	fep->phy_id |= (mii_reg & 0xffff);
> -	printk("fec: PHY @ 0x%x, ID 0x%08x", fep->phy_addr, fep->phy_id);
> -
> -	for(i = 0; phy_info[i]; i++) {
> -		if(phy_info[i]->id == (fep->phy_id >> 4))
> -			break;
> -	}
> -
> -	if (phy_info[i])
> -		printk(" -- %s\n", phy_info[i]->name);
> -	else
> -		printk(" -- unknown PHY!\n");
> +	struct fec_enet_private *fep = netdev_priv(dev);
>  
> -	fep->phy = phy_info[i];
> -	fep->phy_id_done = 1;
> +	strcpy(info->driver, fep->pdev->dev.driver->name);
> +	strcpy(info->version, "Revision: 1.0");
> +	strcpy(info->bus_info, dev_name(&dev->dev));
>  }
>  
> -/* Scan all of the MII PHY addresses looking for someone to respond
> - * with a valid ID.  This usually happens quickly.
> - */
> -static void
> -mii_discover_phy(uint mii_reg, struct net_device *dev)
> -{
> -	struct fec_enet_private *fep;
> -	uint phytype;
> -
> -	fep = netdev_priv(dev);
> -
> -	if (fep->phy_addr < 32) {
> -		if ((phytype = (mii_reg & 0xffff)) != 0xffff && phytype != 0) {
> -
> -			/* Got first part of ID, now get remainder */
> -			fep->phy_id = phytype << 16;
> -			mii_queue_unlocked(dev, mk_mii_read(MII_REG_PHYIR2),
> -							mii_discover_phy3);
> -		} else {
> -			fep->phy_addr++;
> -			mii_queue_unlocked(dev, mk_mii_read(MII_REG_PHYIR1),
> -							mii_discover_phy);
> -		}
> -	} else {
> -		printk("FEC: No PHY device found.\n");
> -		/* Disable external MII interface */
> -		writel(0, fep->hwp + FEC_MII_SPEED);
> -		fep->phy_speed = 0;
> -#ifdef HAVE_mii_link_interrupt
> -		fec_disable_phy_intr(dev);
> -#endif
> -	}
> -}
> +static struct ethtool_ops fec_enet_ethtool_ops = {
> +	.get_settings		= fec_enet_get_settings,
> +	.set_settings		= fec_enet_set_settings,
> +	.get_drvinfo		= fec_enet_get_drvinfo,
> +	.get_link		= ethtool_op_get_link,
> +};
>  
> -/* This interrupt occurs when the PHY detects a link change */
> -#ifdef HAVE_mii_link_interrupt
> -static irqreturn_t
> -mii_link_interrupt(int irq, void * dev_id)
> +static int fec_enet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
>  {
> -	struct	net_device *dev = dev_id;
>  	struct fec_enet_private *fep = netdev_priv(dev);
> +	struct phy_device *phydev = fep->phy_dev;
>  
> -	mii_do_cmd(dev, fep->phy->ack_int);
> -	mii_do_cmd(dev, phy_cmd_relink);  /* restart and display status */
> +	if (!netif_running(dev))
> +		return -EINVAL;
>  
> -	return IRQ_HANDLED;
> +	if (!phydev)
> +		return -ENODEV;
> +
> +	return phy_mii_ioctl(phydev, if_mii(rq), cmd);
>  }
> -#endif
>  
>  static void fec_enet_free_buffers(struct net_device *dev)
>  {
> @@ -1509,35 +916,8 @@ fec_enet_open(struct net_device *dev)
>  	if (ret)
>  		return ret;
>  
> -	fep->sequence_done = 0;
> -	fep->link = 0;
> -
> -	fec_restart(dev, 1);
> -
> -	if (fep->phy) {
> -		mii_do_cmd(dev, fep->phy->ack_int);
> -		mii_do_cmd(dev, fep->phy->config);
> -		mii_do_cmd(dev, phy_cmd_config);  /* display configuration */
> -
> -		/* Poll until the PHY tells us its configuration
> -		 * (not link state).
> -		 * Request is initiated by mii_do_cmd above, but answer
> -		 * comes by interrupt.
> -		 * This should take about 25 usec per register at 2.5 MHz,
> -		 * and we read approximately 5 registers.
> -		 */
> -		while(!fep->sequence_done)
> -			schedule();
> -
> -		mii_do_cmd(dev, fep->phy->startup);
> -	}
> -
> -	/* Set the initial link state to true. A lot of hardware
> -	 * based on this device does not implement a PHY interrupt,
> -	 * so we are never notified of link change.
> -	 */
> -	fep->link = 1;
> -
> +	/* schedule a link state check */
> +	phy_start(fep->phy_dev);
>  	netif_start_queue(dev);
>  	fep->opened = 1;
>  	return 0;
> @@ -1550,6 +930,7 @@ fec_enet_close(struct net_device *dev)
>  
>  	/* Don't know what to do yet. */
>  	fep->opened = 0;
> +	phy_stop(fep->phy_dev);
>  	netif_stop_queue(dev);
>  	fec_stop(dev);
>  
> @@ -1666,6 +1047,7 @@ static const struct net_device_ops fec_netdev_ops = {
>  	.ndo_validate_addr	= eth_validate_addr,
>  	.ndo_tx_timeout		= fec_timeout,
>  	.ndo_set_mac_address	= fec_set_mac_address,
> +	.ndo_do_ioctl           = fec_enet_ioctl,
>  };
>  
>   /*
> @@ -1689,7 +1071,6 @@ static int fec_enet_init(struct net_device *dev, int index)
>  	}
>  
>  	spin_lock_init(&fep->hw_lock);
> -	spin_lock_init(&fep->mii_lock);
>  
>  	fep->index = index;
>  	fep->hwp = (void __iomem *)dev->base_addr;
> @@ -1716,16 +1097,10 @@ static int fec_enet_init(struct net_device *dev, int index)
>  	fep->rx_bd_base = cbd_base;
>  	fep->tx_bd_base = cbd_base + RX_RING_SIZE;
>  
> -#ifdef HAVE_mii_link_interrupt
> -	fec_request_mii_intr(dev);
> -#endif
>  	/* The FEC Ethernet specific entries in the device structure */
>  	dev->watchdog_timeo = TX_TIMEOUT;
>  	dev->netdev_ops = &fec_netdev_ops;
> -
> -	for (i=0; i<NMII-1; i++)
> -		mii_cmds[i].mii_next = &mii_cmds[i+1];
> -	mii_free = mii_cmds;
> +	dev->ethtool_ops = &fec_enet_ethtool_ops;
>  
>  	/* Set MII speed to 2.5 MHz */
>  	fep->phy_speed = ((((clk_get_rate(fep->clk) / 2 + 4999999)
> @@ -1760,13 +1135,6 @@ static int fec_enet_init(struct net_device *dev, int index)
>  
>  	fec_restart(dev, 0);
>  
> -	/* Queue up command to detect the PHY and initialize the
> -	 * remainder of the interface.
> -	 */
> -	fep->phy_id_done = 0;
> -	fep->phy_addr = 0;
> -	mii_queue(dev, mk_mii_read(MII_REG_PHYIR1), mii_discover_phy);
> -
>  	return 0;
>  }
>  
> @@ -1835,8 +1203,7 @@ fec_restart(struct net_device *dev, int duplex)
>  	writel(0, fep->hwp + FEC_R_DES_ACTIVE);
>  
>  	/* Enable interrupts we wish to service */
> -	writel(FEC_ENET_TXF | FEC_ENET_RXF | FEC_ENET_MII,
> -			fep->hwp + FEC_IMASK);
> +	writel(FEC_ENET_TXF | FEC_ENET_RXF, fep->hwp + FEC_IMASK);
>  }
>  
>  static void
> @@ -1859,7 +1226,6 @@ fec_stop(struct net_device *dev)
>  	/* Clear outstanding MII command interrupts. */
>  	writel(FEC_ENET_MII, fep->hwp + FEC_IEVENT);
>  
> -	writel(FEC_ENET_MII, fep->hwp + FEC_IMASK);
>  	writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
>  }
>  
> @@ -1891,6 +1257,7 @@ fec_probe(struct platform_device *pdev)
>  	memset(fep, 0, sizeof(*fep));
>  
>  	ndev->base_addr = (unsigned long)ioremap(r->start, resource_size(r));
> +	fep->pdev = pdev;
>  
>  	if (!ndev->base_addr) {
>  		ret = -ENOMEM;
> @@ -1926,13 +1293,24 @@ fec_probe(struct platform_device *pdev)
>  	if (ret)
>  		goto failed_init;
>  
> +	ret = fec_enet_mii_init(pdev);
> +	if (ret)
> +		goto failed_mii_init;
> +
>  	ret = register_netdev(ndev);
>  	if (ret)
>  		goto failed_register;
>  
> +	printk(KERN_INFO "%s: Freescale FEC PHY driver [%s] "
> +		"(mii_bus:phy_addr=%s, irq=%d)\n", ndev->name,
> +		fep->phy_dev->drv->name, dev_name(&fep->phy_dev->dev),
> +		fep->phy_dev->irq);
> +
>  	return 0;
>  
>  failed_register:
> +	fec_enet_mii_remove(fep);
> +failed_mii_init:
>  failed_init:
>  	clk_disable(fep->clk);
>  	clk_put(fep->clk);
> @@ -1959,6 +1337,7 @@ fec_drv_remove(struct platform_device *pdev)
>  	platform_set_drvdata(pdev, NULL);
>  
>  	fec_stop(ndev);
> +	fec_enet_mii_remove(fep);
>  	clk_disable(fep->clk);
>  	clk_put(fep->clk);
>  	iounmap((void __iomem *)ndev->base_addr);


-- 
------------------------------------------------------------------------
Greg Ungerer  --  Principal Engineer        EMAIL:     gerg at snapgear.com
SnapGear Group, McAfee                      PHONE:       +61 7 3435 2888
8 Gardner Close                             FAX:         +61 7 3217 5323
Milton, QLD, 4064, Australia                WEB: http://www.SnapGear.com




More information about the kernel-team mailing list