[Bug 33269] Re: root filesystem fails to mount (sata_nv module is loaded)
justinchudgar
justin at justinzane.com
Thu Aug 24 18:26:21 UTC 2006
I am having a very similar problem. I am using a Pentium D 805 dual core
on a ECS RC410L/800-Mv2.0, 3 IDE HDDs, 0 SATA devices, 1 IDE HDD. I have
tried installing from both the 6.06 alternate install CD and the 6.06
desktop CD. In either case, the system works fine, but with only 1 CPU
used. When I apt-get install linux-image-smp (and the associated
restricted modules), the system will begin to boot, but stop at
"mounting root file system..." and never respond again, even after long
(multiple hour) waits.
I can boot back into the 386 uniprocessor kernel just fine, so it does
not prevent me from using the system. I then tried doing a dist-upgrade
to edgy; and, this also works with the default UP 386 kernel. But, apt-
get'ing the 686 smp kernel again stops at the same place.
I tried using kpkg to build my own kernel and, again, had the same
failure. I have tried dpkg-reconfigure udev before rebooting into the
new kernel, to no avail.
Following is the dmesg output:
-------------------------------------------------
[17179569.184000] Linux version 2.6.17-6-386 (root at rothera) (gcc version 4.1.2 20060715 (prerelease) (Ubuntu 4.1.1-9ubuntu1)) #2 Fri Aug 11 22:05:08 UTC 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000003bfd0000 (usable)
[17179569.184000] BIOS-e820: 000000003bfd0000 - 000000003bfde000 (ACPI data)
[17179569.184000] BIOS-e820: 000000003bfde000 - 000000003c000000 (ACPI NVS)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[17179569.184000] 63MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000ff780
[17179569.184000] On node 0 totalpages: 245712
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] Normal zone: 225280 pages, LIFO batch:31
[17179569.184000] HighMem zone: 16336 pages, LIFO batch:3
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 ACPIAM ) @ 0x000f87f0
[17179569.184000] ACPI: RSDT (v001 A M I OEMRSDT 0x02000615 MSFT 0x00000097) @ 0x3bfd0000
[17179569.184000] ACPI: FADT (v002 A M I OEMFACP 0x02000615 MSFT 0x00000097) @ 0x3bfd0200
[17179569.184000] ACPI: MADT (v001 A M I OEMAPIC 0x02000615 MSFT 0x00000097) @ 0x3bfd0390
[17179569.184000] ACPI: MCFG (v001 A M I OEMMCFG 0x02000615 MSFT 0x00000097) @ 0x3bfd0400
[17179569.184000] ACPI: OEMB (v001 A M I AMI_OEM 0x02000615 MSFT 0x00000097) @ 0x3bfde040
[17179569.184000] ACPI: HPET (v001 A M I OEMHPET 0x02000615 MSFT 0x00000097) @ 0x3bfd49d0
[17179569.184000] ACPI: DSDT (v001 RC410 RC410L 0x00000000 INTL 0x02002026) @ 0x00000000
[17179569.184000] ATI board detected. Disabling timer routing over 8254.
[17179569.184000] ACPI: PM-Timer IO Port: 0x808
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:4 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[17179569.184000] Processor #1 15:4 APIC version 20
[17179569.184000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[17179569.184000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[17179569.184000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] ACPI: HPET id: 0x0 base: 0xfed00000
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 40000000 (gap: 3c000000:c2e00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=UUID=3e161218-3019-40cf-9f3d-6b4f888dd7a8 ro quiet splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[17179569.184000] Console: colour VGA+ 80x25
[17179569.184000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179569.184000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179569.184000] Memory: 962076k/982848k available (1818k kernel code, 20168k reserved, 1040k data, 288k init, 65344k highmem)
[17179569.184000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179569.184000] hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0, 0
[17179569.184000] hpet0: 4 32-bit timers, 14318180 Hz
[17179569.184000] Using HPET for base-timer
[17179569.184000] Using HPET for gettimeofday
[17179569.184000] Detected 3337.924 MHz processor.
[17179569.184000] Using hpet for high-res timesource
[17179569.268000] Calibrating delay using timer specific routine.. 6683.45 BogoMIPS (lpj=13366915)
[17179569.268000] Security Framework v1.0.0 initialized
[17179569.268000] SELinux: Disabled at boot.
[17179569.268000] Mount-cache hash table entries: 512
[17179569.268000] CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000001
[17179569.268000] CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000001
[17179569.268000] monitor/mwait feature present.
[17179569.268000] using mwait in idle threads.
[17179569.268000] CPU: Trace cache: 12K uops, L1 D cache: 16K
[17179569.268000] CPU: L2 cache: 1024K
[17179569.268000] CPU: After all inits, caps: bfebfbff 20000000 00000000 00000180 0000651d 00000000 00000001
[17179569.268000] CPU: Intel(R) Pentium(R) D CPU 2.66GHz stepping 07
[17179569.268000] Checking 'hlt' instruction... OK.
[17179569.284000] SMP alternatives: switching to UP code
[17179569.284000] Freeing SMP alternatives: 0k freed
[17179569.284000] checking if image is initramfs... it is
[17179569.904000] Freeing initrd memory: 8124k freed
[17179569.904000] ACPI: Looking for DSDT ... not found!
[17179569.904000] ENABLING IO-APIC IRQs
[17179569.908000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179569.908000] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[17179569.908000] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[17179569.908000] ...trying to set up timer as Virtual Wire IRQ... works.
[17179570.096000] NET: Registered protocol family 16
[17179570.096000] EISA bus registered
[17179570.096000] ACPI: bus type pci registered
[17179570.096000] PCI: BIOS Bug: MCFG area is not E820-reserved
[17179570.096000] PCI: Not using MMCONFIG.
[17179570.096000] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[17179570.096000] Setting up standard PCI resources
[17179570.104000] ACPI: Subsystem revision 20060127
[17179570.108000] ACPI: Interpreter enabled
[17179570.108000] ACPI: Using IOAPIC for interrupt routing
[17179570.112000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179570.112000] PCI: Probing PCI hardware (bus 00)
[17179570.116000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
[17179570.116000] Boot video device is 0000:01:05.0
[17179570.116000] PCI: Transparent bridge - 0000:00:14.4
[17179570.116000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179570.124000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[17179570.132000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[17179570.136000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[17179570.136000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[17179570.136000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[17179570.136000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[17179570.136000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[17179570.136000] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[17179570.136000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[17179570.136000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[17179570.136000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179570.136000] pnp: PnP ACPI init
[17179570.144000] pnp: PnP ACPI: found 13 devices
[17179570.144000] PnPBIOS: Disabled by ACPI PNP
[17179570.144000] PCI: Using ACPI for IRQ routing
[17179570.144000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[17179570.144000] PCI: Cannot allocate resource region 3 of device 0000:00:00.0
[17179570.152000] pnp: 00:08: ioport range 0xa00-0xa0f has been reserved
[17179570.152000] pnp: 00:08: ioport range 0xa10-0xa1f has been reserved
[17179570.152000] pnp: 00:08: ioport range 0xa20-0xa2f has been reserved
[17179570.152000] pnp: 00:08: ioport range 0xa30-0xa3f has been reserved
[17179570.156000] PCI: Bridge: 0000:00:01.0
[17179570.156000] IO window: 5000-5fff
[17179570.156000] MEM window: fa700000-fa7fffff
[17179570.156000] PREFETCH window: cff00000-dfefffff
[17179570.156000] PCI: Bridge: 0000:00:14.4
[17179570.156000] IO window: 6000-6fff
[17179570.156000] MEM window: fa800000-fe8fffff
[17179570.156000] PREFETCH window: 40000000-400fffff
[17179570.156000] NET: Registered protocol family 2
[17179570.192000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179570.192000] TCP established hash table entries: 131072 (order: 7, 524288 bytes)
[17179570.192000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.192000] TCP: Hash tables configured (established 131072 bind 65536)
[17179570.192000] TCP reno registered
[17179570.192000] audit: initializing netlink socket (disabled)
[17179570.192000] audit(1156417144.192:1): initialized
[17179570.192000] highmem bounce pool size: 64 pages
[17179570.192000] VFS: Disk quotas dquot_6.5.1
[17179570.192000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179570.192000] Initializing Cryptographic API
[17179570.192000] io scheduler noop registered
[17179570.192000] io scheduler anticipatory registered
[17179570.192000] io scheduler deadline registered
[17179570.192000] io scheduler cfq registered (default)
[17179570.192000] isapnp: Scanning for PnP cards...
[17179570.552000] isapnp: No Plug & Play device found
[17179570.568000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179570.568000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179570.572000] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179570.572000] mice: PS/2 mouse device common for all mice
[17179570.572000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179570.572000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179570.572000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179570.572000] PNP: No PS/2 controller found. Probing ports directly.
[17179570.572000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179570.572000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179570.572000] EISA: Probing bus 0 at eisa.0
[17179570.572000] Cannot allocate resource for EISA slot 5
[17179570.572000] Cannot allocate resource for EISA slot 6
[17179570.572000] EISA: Detected 0 cards.
[17179570.572000] TCP bic registered
[17179570.572000] NET: Registered protocol family 1
[17179570.572000] NET: Registered protocol family 8
[17179570.572000] NET: Registered protocol family 20
[17179570.572000] Using IPI Shortcut mode
[17179570.572000] ACPI wakeup devices:
[17179570.572000] SBAZ UAR1 P0P9 AC97 MC97 USB1 USB2 EUSB PCE2 PCE3 PCE4 PCE5 PCE6 PCE7 PWRB
[17179570.572000] ACPI: (supports S0 S1 S3 S4 S5)
[17179570.572000] Freeing unused kernel memory: 288k freed
[17179571.636000] Capability LSM initialized
[17179571.660000] ACPI Error (psparse-0517): Method parse/execution failed [\_PR_.CPU1._PDC] (Node c18515a0), AE_BAD_HEADER
[17179571.664000] ACPI: Thermal Zone [THRM] (-269 C)
[17179571.964000] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[17179571.964000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 177
[17179571.964000] ATIIXP: chipset revision 128
[17179571.964000] ATIIXP: not 100% native mode: will probe irqs later
[17179571.964000] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
[17179571.964000] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
[17179571.964000] Probing IDE interface ide0...
[17179572.252000] hda: IC35L060AVV207-0, ATA DISK drive
[17179572.532000] hdb: QUANTUM FIREBALLP AS20.5, ATA DISK drive
[17179572.588000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179572.608000] Probing IDE interface ide1...
[17179573.344000] hdc: _NEC CD-RW NR-9300A, ATAPI CD/DVD-ROM drive
[17179573.624000] hdd: ST320413A, ATA DISK drive
[17179573.680000] ide1 at 0x170-0x177,0x376 on irq 15
[17179573.692000] hda: max request size: 512KiB
[17179573.704000] hda: 117187500 sectors (60000 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
[17179573.704000] hda: cache flushes supported
[17179573.704000] hda: hda1
[17179573.720000] hdb: max request size: 128KiB
[17179573.720000] hdb: 40132503 sectors (20547 MB) w/1902KiB Cache, CHS=39813/16/63, UDMA(100)
[17179573.720000] hdb: cache flushes not supported
[17179573.720000] hdb: hdb1 hdb2 < hdb5 >
[17179573.744000] hdd: max request size: 128KiB
[17179573.744000] hdd: 39102336 sectors (20020 MB) w/512KiB Cache, CHS=38792/16/63, UDMA(100)
[17179573.744000] hdd: cache flushes not supported
[17179573.744000] hdd: hdd1
[17179573.784000] hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[17179573.784000] Uniform CD-ROM driver Revision: 3.20
[17179574.284000] hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[17179574.284000] hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
[17179574.284000] ide: failed opcode was: unknown
[17179574.936000] hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[17179574.936000] hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
[17179574.936000] ide: failed opcode was: unknown
[17179575.600000] hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[17179575.600000] hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
[17179575.600000] ide: failed opcode was: unknown
[17179576.276000] hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
[17179576.276000] hdd: dma_intr: error=0x84 { DriveStatusError BadCRC }
[17179576.276000] ide: failed opcode was: unknown
[17179576.276000] hdc: DMA disabled
[17179576.324000] ide1: reset: success
[17179576.796000] SCSI subsystem initialized
[17179576.800000] libata version 1.20 loaded.
[17179576.800000] sata_sil 0000:00:11.0: version 0.9
[17179576.800000] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 185
[17179576.800000] ata1: SATA max UDMA/100 cmd 0xF883E880 ctl 0xF883E88A bmdma 0xF883E800 irq 185
[17179576.800000] ata2: SATA max UDMA/100 cmd 0xF883E8C0 ctl 0xF883E8CA bmdma 0xF883E808 irq 185
[17179577.004000] ata1: SATA link down (SStatus 0)
[17179577.004000] scsi0 : sata_sil
[17179577.208000] ata2: SATA link down (SStatus 0)
[17179577.208000] scsi1 : sata_sil
[17179577.208000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 193
[17179577.208000] ata3: SATA max UDMA/100 cmd 0xF8858C80 ctl 0xF8858C8A bmdma 0xF8858C00 irq 193
[17179577.208000] ata4: SATA max UDMA/100 cmd 0xF8858CC0 ctl 0xF8858CCA bmdma 0xF8858C08 irq 193
[17179577.412000] ata3: SATA link down (SStatus 0)
[17179577.412000] scsi2 : sata_sil
[17179577.616000] ata4: SATA link down (SStatus 0)
[17179577.616000] scsi3 : sata_sil
[17179577.712000] usbcore: registered new driver usbfs
[17179577.712000] usbcore: registered new driver hub
[17179577.736000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179577.736000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 201
[17179577.736000] ohci_hcd 0000:00:13.0: OHCI Host Controller
[17179577.736000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[17179577.768000] ohci_hcd 0000:00:13.0: irq 201, io mem 0xfebfe000
[17179577.828000] usb usb1: configuration #1 chosen from 1 choice
[17179577.828000] hub 1-0:1.0: USB hub found
[17179577.828000] hub 1-0:1.0: 4 ports detected
[17179577.932000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 201
[17179577.932000] ohci_hcd 0000:00:13.1: OHCI Host Controller
[17179577.932000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[17179577.960000] ohci_hcd 0000:00:13.1: irq 201, io mem 0xfebfd000
[17179578.020000] usb usb2: configuration #1 chosen from 1 choice
[17179578.020000] hub 2-0:1.0: USB hub found
[17179578.020000] hub 2-0:1.0: 4 ports detected
[17179578.124000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 201
[17179578.124000] ehci_hcd 0000:00:13.2: EHCI Host Controller
[17179578.124000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[17179578.124000] ehci_hcd 0000:00:13.2: irq 201, io mem 0xfebfc000
[17179578.124000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179578.124000] usb usb3: configuration #1 chosen from 1 choice
[17179578.124000] hub 3-0:1.0: USB hub found
[17179578.124000] hub 3-0:1.0: 8 ports detected
[17179578.348000] Attempting manual resume
[17179578.368000] kjournald starting. Commit interval 5 seconds
[17179578.368000] EXT3-fs: mounted filesystem with ordered data mode.
[17179579.108000] usb 1-1: new low speed USB device using ohci_hcd and address 3
[17179579.316000] usb 1-1: configuration #1 chosen from 1 choice
[17179579.320000] ohci_hcd 0000:00:13.1: wakeup
[17179579.704000] usb 2-2: new low speed USB device using ohci_hcd and address 2
[17179579.916000] usb 2-2: configuration #1 chosen from 1 choice
[17179588.496000] usbcore: registered new driver hiddev
[17179588.504000] input: Logitech Inc. iFeel Mouse as /class/input/input0
[17179588.504000] input: USB HID v1.00 Mouse [Logitech Inc. iFeel Mouse ] on usb-0000:00:13.0-1
[17179588.512000] input: DELL DELL USB Keyboard as /class/input/input1
[17179588.512000] input: USB HID v1.10 Keyboard [DELL DELL USB Keyboard] on usb-0000:00:13.1-2
[17179588.548000] input: DELL DELL USB Keyboard as /class/input/input2
[17179588.548000] input: USB HID v1.10 Device [DELL DELL USB Keyboard] on usb-0000:00:13.1-2
[17179588.548000] usbcore: registered new driver usbhid
[17179588.548000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179588.624000] 8139too Fast Ethernet driver 0.9.27
[17179588.624000] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 20 (level, low) -> IRQ 209
[17179588.624000] eth0: RealTek RTL8139 at 0xf886ec00, 00:14:2a:db:7e:4b, IRQ 209
[17179588.624000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[17179588.748000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17179588.900000] input: PC Speaker as /class/input/input3
[17179589.148000] eth0: link down
[17179589.152000] Floppy drive(s): fd0 is 1.44M
[17179589.168000] FDC 0 is a post-1991 82077
[17179589.236000] Real Time Clock Driver v1.12ac
[17179589.260000] ts: Compaq touchscreen protocol output
[17179589.272000] ath_hal: module license 'Proprietary' taints kernel.
[17179589.272000] ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[17179589.348000] parport: PnPBIOS parport detected.
[17179589.348000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179589.368000] Linux agpgart interface v0.101 (c) Dave Jones
[17179589.392000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179589.396000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179589.936000] wlan: 0.8.4.2 (0.9.2)
[17179589.936000] ath_rate_sample: 1.2 (0.9.2)
[17179589.940000] ath_pci: 0.9.4.5 (0.9.2)
[17179589.940000] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 169
[17179590.492000] NET: Registered protocol family 17
[17179590.596000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[17179590.596000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[17179590.596000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[17179590.596000] wifi0: mac 7.8 phy 4.5 radio 5.6
[17179590.596000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[17179590.596000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[17179590.596000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[17179590.596000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[17179590.596000] wifi0: Use hw queue 8 for CAB traffic
[17179590.596000] wifi0: Use hw queue 9 for beacons
[17179590.608000] wifi0: Atheros 5212: mem=0xfe8f0000, irq=169
[17179591.148000] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 217
[17179591.648000] lp0: using parport0 (interrupt-driven).
[17179591.728000] it87: Found IT8712F chip at 0xa10, revision 7
[17179591.844000] Adding 851404k swap on /dev/disk/by-uuid/38293417-d042-495c-ab7a-93754c23576f. Priority:-1 extents:1 across:851404k
[17179591.984000] EXT3 FS on hdb1, internal journal
[17179592.176000] device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel at redhat.com
[17179596.620000] NET: Registered protocol family 10
[17179596.620000] lo: Disabled Privacy Extensions
[17179596.620000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[17179596.620000] IPv6 over IPv4 tunneling driver
[17179598.480000] ACPI: Power Button (FF) [PWRF]
[17179598.480000] ACPI: Power Button (CM) [PWRB]
[17179598.548000] ibm_acpi: ec object not found
[17179598.576000] pcc_acpi: loading...
[17179606.352000] [drm] Initialized drm 1.0.1 20051102
[17179607.300000] ath0: no IPv6 routers present
[17179607.936000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[17179607.936000] apm: overridden by ACPI.
[17179610.636000] Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
[17179610.972000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[17179610.992000] NFSD: starting 90-second grace period
[17179617.952000] Bluetooth: Core ver 2.8
[17179617.952000] NET: Registered protocol family 31
[17179617.952000] Bluetooth: HCI device and connection manager initialized
[17179617.952000] Bluetooth: HCI socket layer initialized
[17179617.996000] Bluetooth: L2CAP ver 2.8
[17179617.996000] Bluetooth: L2CAP socket layer initialized
[17179618.024000] Bluetooth: HIDP (Human Interface Emulation) ver 1.1-mh1
[17179618.036000] Bluetooth: RFCOMM socket layer initialized
[17179618.036000] Bluetooth: RFCOMM TTY layer initialized
[17179618.036000] Bluetooth: RFCOMM ver 1.7
--------------------------------------------------
end of dmesg output
--
root filesystem fails to mount (sata_nv module is loaded)
https://launchpad.net/bugs/33269
More information about the kernel-team
mailing list