kernel crash on Intel(R) Xeon(TM) CPU 2.66GHz 4-cpus machine

[Andrea Puglisi]

Again!

After leaving the new 4 simulations runnning, I've been out for the 
weekend and come back this morning to find out the pc completely dead 
(power was on, but monitor was black, no answer to any input device 
stimulus). The first time I run the simulations, all data were written on 
the external (usb) disk: fearing this could have been the cause of the 
first failure, I run this new simulations entirely on /dev/hda. But it 
crashed again.

> Test memory. That's the main cause I've seen that freeze the machine.

I've just tested it, with memtest86 (ver. 1.65). It passed the test 
completely with no errors.


> > Also, just to be sure, what is the machine? Dell? Have you a SCSI RAID
card? PERC3?

The machine is a HP (workstation xw6000). I suppose to have a pci scsi 
card (it appears in the bios setup, at the voice pci devices, occupying 
two irqs), and cat /proc/scsi/scsi returns

Attached devices:
Host: scsi2 Channel: 00 Id: 00 Lun: 00
   Vendor: Maxtor   Model: 6Y160P0          Rev: YAR4
   Type:   Direct-Access

(is this the scsi card or just the optical driver seen as a scsi device?)


> > And since his machine is 3 years old, I think it's not a 64bits capable 
> > one...

yes, I would exclude 64bit, it's a Xeon DP 2658Mhz; in fact I've just 
discovered (looking at system config in the BIOS setup) that I have *two* 
processors (this is not my machine, I've been started working on it 
recently), which are of course not dual core... therefore I really do not 
understand why linux recognized 4 processors!!



> > > When it froze, were you in X or on the console? If you were in X, this
> > > could explain why you didn't see any messages. Attempting to reproduce
> > > the freeze while at the console would be advisable.

normally when X crashes I can still switch to other consoles with 
ctrl-alt-f1 (f2, f3 etc...); with these crashes, instead, the keyboard is
completely frozen; moreover while I'm on X it of course keeps writing 
messages to /var/log/* files; instead I could not find any message written 
at the time of the crash


today I can't still find any hint in the many log files; I just report you 
a message which is often repeated (at random times):

kernel: [17203596.832000] Inbound IN=eth0 OUT= MAC=xxx SRC=38.119.250.76 
DST=xxx LEN=48 TOS=0x00 PREC=0x00 TTL=113 ID=1643 DF PROTO=TCP SPT=2490 
DPT=10000 WINDOW=65535 RES=0x00 SYN URGP=0

where of course "xxx" are mac address and tcp (local) address (the address 
in SRC is unknown to me)

is this just a strange external connection tentative or a clue that the 
NIC is mis-working? one of these messages appears to be the last wrote 
line I've found browsing the log files (this doesn't mean anything, of 
course)

what does also mean the message (in syslog and message)
-- MARK --
? what is marking?

I attach to this message my "dmesg" actual file (the one containing the 
buffer since the last boot of this morning), maybe you can discover some 
clue, for example why it recognizes FOUR processors

> > You could also send the syslog to a remote machine, so if there is a 
> > disk problem, you have more chances getting the log message if any. 
> > Ben, would the kdump kernel be useful in this situation?
> 
> The kdump would help, but I haven't setup any useful tools for it yet.

what does it mean? it's unusable or I can try it?

> OK, but will this user be able to jump in the kdump kernel if everything
> is frozen? Is there some special magic thing (serial port, else?) that
> trigger the "dump to disk" condition?

ok, I wait you explain me this kdup possibility, if you can, thanks

meanwhile I will try to use the machine without executing simulations

thanks a lot for your help!

  have a good day

  andrea
-------------- next part --------------
[17179569.184000] Linux version 2.6.15-26-686 (buildd at terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Thu Aug 3 03:13:28 UTC 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 0000000040000000 (usable)
[17179569.184000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[17179569.184000] 128MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f9bf0
[17179569.184000] On node 0 totalpages: 262144
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000]   Normal zone: 225280 pages, LIFO batch:31
[17179569.184000]   HighMem zone: 32768 pages, LIFO batch:7
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 COMPAQ                                ) @ 0x000ea810
[17179569.184000] ACPI: RSDT (v001 COMPAQ CPQ0054  0x20021018  0x00000000) @ 0x000e6540
[17179569.184000] ACPI: FADT (v001 COMPAQ PLACER   0x00000001  0x00000000) @ 0x000e65f8
[17179569.184000] ACPI: SSDT (v001 COMPAQ  PROJECT 0x00000001 MSFT 0x0100000e) @ 0x000e734d
[17179569.184000] ACPI: SSDT (v001 COMPAQ CORE_PNP 0x00000001 MSFT 0x0100000e) @ 0x000e78e7
[17179569.184000] ACPI: SSDT (v001 COMPAQ CORE_UTL 0x00000001 MSFT 0x0100000e) @ 0x000e7e21
[17179569.184000] ACPI: SSDT (v001 COMPAQ VILLTBL1 0x00000001 MSFT 0x0100000e) @ 0x000e7fbc
[17179569.184000] ACPI: SSDT (v001 COMPAQ LGCYLITE 0x00000001 MSFT 0x0100000e) @ 0x000e82c4
[17179569.184000] ACPI: SSDT (v001 COMPAQ    UART2 0x00000001 MSFT 0x0100000e) @ 0x000e8803
[17179569.184000] ACPI: SSDT (v001 COMPAQ   FLOPPY 0x00000001 MSFT 0x0100000e) @ 0x000e896a
[17179569.184000] ACPI: MADT (v001 COMPAQ PLACER   0x00000001  0x00000000) @ 0x000e666c
[17179569.184000] ACPI: SSDT (v001 COMPAQ     APIC 0x00000001 MSFT 0x0100000e) @ 0x000ea42f
[17179569.184000] ACPI: ASF! (v016 COMPAQ PLACER   0x00000001  0x00000000) @ 0x000e66f0
[17179569.184000] ACPI: SSDT (v001 COMPAQ PNP_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e8f26
[17179569.184000] ACPI: SSDT (v001 COMPAQ UR2_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e934a
[17179569.184000] ACPI: SSDT (v001 COMPAQ FPY_PRSS 0x00000001 MSFT 0x0100000e) @ 0x000e94b7
[17179569.184000] ACPI: SSDT (v001 COMPAQ       S1 0x00000001 MSFT 0x0100000e) @ 0x000e95d0
[17179569.184000] ACPI: SSDT (v001 COMPAQ      L08 0x00000001 MSFT 0x0100000e) @ 0x000ea1d2
[17179569.184000] ACPI: SSDT (v001 COMPAQ    FINIS 0x00000001 MSFT 0x0100000e) @ 0x000ea5ca
[17179569.184000] ACPI: DSDT (v001 COMPAQ     DSDT 0x00000001 MSFT 0x0100000e) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0xf808
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
[17179569.184000] Processor #6 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[17179569.184000] Processor #1 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled)
[17179569.184000] Processor #7 15:2 APIC version 20
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda1 ro quiet splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[17179569.184000] Detected 2658.614 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179570.156000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179570.160000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.188000] Memory: 1027288k/1048576k available (2110k kernel code, 20620k reserved, 595k data, 332k init, 131072k highmem)
[17179570.188000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179570.272000] Calibrating delay using timer specific routine.. 5322.82 BogoMIPS (lpj=10645654)
[17179570.272000] Security Framework v1.0.0 initialized
[17179570.272000] SELinux:  Disabled at boot.
[17179570.272000] Mount-cache hash table entries: 512
[17179570.272000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179570.272000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179570.272000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179570.272000] CPU: L2 cache: 512K
[17179570.272000] CPU: Hyper-Threading is disabled
[17179570.272000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00000400 00000000 00000000
[17179570.272000] mtrr: v2.0 (20020519)
[17179570.272000] Enabling fast FPU save and restore... done.
[17179570.272000] Enabling unmasked SIMD FPU exception support... done.
[17179570.272000] Checking 'hlt' instruction... OK.
[17179570.288000] SMP alternatives: switching to UP code
[17179570.288000] checking if image is initramfs... it is
[17179570.776000] Freeing initrd memory: 6809k freed
[17179570.784000] ACPI: Looking for DSDT ... not found!
[17179570.788000] CPU0: Intel(R) Xeon(TM) CPU 2.66GHz stepping 07
[17179570.788000] SMP alternatives: switching to SMP code
[17179570.788000] Booting processor 1/1 eip 3000
[17179570.800000] Initializing CPU#1
[17179570.880000] Calibrating delay using timer specific routine.. 5316.65 BogoMIPS (lpj=10633302)
[17179570.880000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179570.880000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179570.880000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179570.880000] CPU: L2 cache: 512K
[17179570.880000] CPU: Hyper-Threading is disabled
[17179570.880000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00000400 00000000 00000000
[17179570.880000] CPU1: Intel(R) Xeon(TM) CPU 2.66GHz stepping 07
[17179570.880000] SMP alternatives: switching to SMP code
[17179570.880000] Booting processor 2/6 eip 3000
[17179570.888000] Initializing CPU#2
[17179570.968000] Calibrating delay using timer specific routine.. 5316.53 BogoMIPS (lpj=10633070)
[17179570.968000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179570.968000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179570.968000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179570.968000] CPU: L2 cache: 512K
[17179570.968000] CPU: Hyper-Threading is disabled
[17179570.968000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00000400 00000000 00000000
[17179570.968000] CPU2: Intel(R) Xeon(TM) CPU 2.66GHz stepping 07
[17179570.968000] SMP alternatives: switching to SMP code
[17179570.968000] Booting processor 3/7 eip 3000
[17179570.976000] Initializing CPU#3
[17179571.056000] Calibrating delay using timer specific routine.. 5316.59 BogoMIPS (lpj=10633184)
[17179571.056000] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179571.056000] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00000400 00000000 00000000
[17179571.056000] CPU: Trace cache: 12K uops, L1 D cache: 8K
[17179571.056000] CPU: L2 cache: 512K
[17179571.056000] CPU: Hyper-Threading is disabled
[17179571.056000] CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00000400 00000000 00000000
[17179571.056000] CPU3: Intel(R) Xeon(TM) CPU 2.66GHz stepping 07
[17179571.056000] Total of 4 processors activated (21272.60 BogoMIPS).
[17179571.056000] ENABLING IO-APIC IRQs
[17179571.056000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179571.200000] checking TSC synchronization across 4 CPUs: passed.
[17179571.212000] Brought up 4 CPUs
[17179571.212000] NET: Registered protocol family 16
[17179571.212000] EISA bus registered
[17179571.212000] ACPI: bus type pci registered
[17179571.212000] PCI: PCI BIOS revision 2.20 entry at 0xecdf4, last bus=5
[17179571.212000] PCI: Using configuration type 1
[17179571.212000] ACPI: Subsystem revision 20051216
[17179571.212000] ACPI: Interpreter enabled
[17179571.212000] ACPI: Using IOAPIC for interrupt routing
[17179571.212000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
[17179571.212000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15)
[17179571.212000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15)
[17179571.216000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
[17179571.216000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[17179571.216000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15)
[17179571.216000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 14 15)
[17179571.216000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 14 15)
[17179571.216000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179571.216000] PCI: Probing PCI hardware (bus 00)
[17179571.216000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[17179571.216000] PCI quirk: region f800-f87f claimed by ICH4 ACPI/GPIO/TCO
[17179571.216000] PCI quirk: region fa00-fa3f claimed by ICH4 GPIO
[17179571.216000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[17179571.216000] Boot video device is 0000:01:00.0
[17179571.216000] PCI: Transparent bridge - 0000:00:1e.0
[17179571.216000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179571.220000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
[17179571.224000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179571.224000] pnp: PnP ACPI init
[17179571.228000] pnp: PnP ACPI: found 14 devices
[17179571.228000] PnPBIOS: Disabled by ACPI PNP
[17179571.228000] PCI: Using ACPI for IRQ routing
[17179571.228000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179571.276000] pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
[17179571.276000] pnp: 00:0c: ioport range 0x400-0x41f has been reserved
[17179571.276000] pnp: 00:0c: ioport range 0x420-0x43f has been reserved
[17179571.276000] pnp: 00:0c: ioport range 0x440-0x45f has been reserved
[17179571.276000] pnp: 00:0c: ioport range 0x460-0x47f could not be reserved
[17179571.276000] pnp: 00:0c: ioport range 0xf800-0xf81f could not be reserved
[17179571.276000] pnp: 00:0c: ioport range 0xf820-0xf83f could not be reserved
[17179571.276000] pnp: 00:0c: ioport range 0xf840-0xf85f has been reserved
[17179571.276000] pnp: 00:0c: ioport range 0xf860-0xf87f has been reserved
[17179571.276000] PCI: Bridge: 0000:00:01.0
[17179571.276000]   IO window: disabled.
[17179571.276000]   MEM window: f1000000-f21fffff
[17179571.276000]   PREFETCH window: e8000000-f01fffff
[17179571.276000] PCI: Bridge: 0000:00:1e.0
[17179571.276000]   IO window: 1000-1fff
[17179571.276000]   MEM window: f0200000-f04fffff
[17179571.276000]   PREFETCH window: 50000000-501fffff
[17179571.276000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[17179571.276000] audit: initializing netlink socket (disabled)
[17179571.276000] audit(1156159845.272:1): initialized
[17179571.276000] highmem bounce pool size: 64 pages
[17179571.276000] VFS: Disk quotas dquot_6.5.1
[17179571.276000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179571.276000] Initializing Cryptographic API
[17179571.276000] io scheduler noop registered
[17179571.276000] io scheduler anticipatory registered
[17179571.276000] io scheduler deadline registered
[17179571.276000] io scheduler cfq registered
[17179571.276000] isapnp: Scanning for PnP cards...
[17179571.628000] isapnp: No Plug & Play device found
[17179571.652000] Real Time Clock Driver v1.12
[17179571.652000] PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[17179571.652000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179571.652000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179571.652000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[17179571.652000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.656000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179571.656000] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.656000] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179571.656000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179571.656000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179571.656000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179571.660000] mice: PS/2 mouse device common for all mice
[17179571.660000] EISA: Probing bus 0 at eisa.0
[17179571.660000] Cannot allocate resource for EISA slot 1
[17179571.660000] Cannot allocate resource for EISA slot 2
[17179571.660000] EISA: Detected 0 cards.
[17179571.660000] NET: Registered protocol family 2
[17179571.684000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179571.708000] IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179571.708000] TCP established hash table entries: 262144 (order: 9, 3145728 bytes)
[17179571.712000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[17179571.712000] TCP: Hash tables configured (established 262144 bind 65536)
[17179571.712000] TCP reno registered
[17179571.712000] TCP bic registered
[17179571.712000] NET: Registered protocol family 1
[17179571.712000] NET: Registered protocol family 8
[17179571.712000] NET: Registered protocol family 20
[17179571.712000] Starting balanced_irq
[17179571.712000] Using IPI No-Shortcut mode
[17179571.712000] ACPI wakeup devices: 
[17179571.712000] PCI0  HUB COM1 COM2 USB1 USB2 USB3 EUSB PBTN 
[17179571.712000] ACPI: (supports S0 S1 S4 S5)
[17179571.712000] Freeing unused kernel memory: 332k freed
[17179571.768000] vga16fb: initializing
[17179571.768000] vga16fb: mapped to 0xc00a0000
[17179571.908000] Console: switching to colour frame buffer device 80x25
[17179571.908000] fb0: VGA16 VGA frame buffer device
[17179572.936000] Capability LSM initialized
[17179572.984000] ACPI: Processor [CPU0] (supports 8 throttling states)
[17179572.988000] ACPI: Processor [CPU2] (supports 8 throttling states)
[17179572.988000] ACPI: Processor [CPU1] (supports 8 throttling states)
[17179572.988000] ACPI: Processor [CPU3] (supports 8 throttling states)
[17179573.628000] SCSI subsystem initialized
[17179573.632000] ACPI: PCI Interrupt 0000:05:0c.0[A] -> GSI 19 (level, low) -> IRQ 169
[17179588.860000] scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
[17179588.860000]         <Adaptec AIC7902 Ultra320 SCSI adapter>
[17179588.860000]         aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
[17179588.860000] 
[17179592.716000] ACPI: PCI Interrupt 0000:05:0c.1[B] -> GSI 22 (level, low) -> IRQ 177
[17179607.944000] scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
[17179607.944000]         <Adaptec AIC7902 Ultra320 SCSI adapter>
[17179607.944000]         aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
[17179607.944000] 
[17179611.884000] ICH4: IDE controller at PCI slot 0000:00:1f.1
[17179611.884000] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[17179611.884000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
[17179611.884000] ICH4: chipset revision 1
[17179611.884000] ICH4: not 100% native mode: will probe irqs later
[17179611.884000]     ide0: BM-DMA at 0x24c0-0x24c7, BIOS settings: hda:DMA, hdb:DMA
[17179611.884000]     ide1: BM-DMA at 0x24c8-0x24cf, BIOS settings: hdc:DMA, hdd:pio
[17179611.884000] Probing IDE interface ide0...
[17179612.172000] hda: Maxtor 6Y080L0, ATA DISK drive
[17179612.452000] hdb: Maxtor 6Y080L0, ATA DISK drive
[17179612.508000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179612.508000] Probing IDE interface ide1...
[17179613.248000] hdc: HL-DT-ST RW/DVD GCC-4320B, ATAPI CD/DVD-ROM drive
[17179613.584000] ide1 at 0x170-0x177,0x376 on irq 15
[17179613.596000] hda: max request size: 1024KiB
[17179613.596000] hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
[17179613.604000] hda: cache flushes supported
[17179613.604000]  hda: hda1 hda2 hda3 hda4
[17179613.620000] hdb: max request size: 1024KiB
[17179613.620000] hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
[17179613.640000] hdb: cache flushes supported
[17179613.640000]  hdb: hdb4 < hdb5 >
[17179613.656000] hdc: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[17179613.656000] Uniform CD-ROM driver Revision: 3.20
[17179614.064000] usbcore: registered new driver usbfs
[17179614.064000] usbcore: registered new driver hub
[17179614.064000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
[17179614.064000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[17179614.064000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[17179614.064000] ehci_hcd 0000:00:1d.7: debug port 1
[17179614.064000] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[17179614.064000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[17179614.064000] ehci_hcd 0000:00:1d.7: irq 193, io mem 0xf0500000
[17179614.068000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179614.068000] hub 1-0:1.0: USB hub found
[17179614.068000] hub 1-0:1.0: 6 ports detected
[17179614.072000] USB Universal Host Controller Interface driver v2.3
[17179614.072000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 201
[17179614.072000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[17179614.072000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[17179614.172000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[17179614.172000] uhci_hcd 0000:00:1d.0: irq 201, io base 0x00002440
[17179614.172000] hub 2-0:1.0: USB hub found
[17179614.172000] hub 2-0:1.0: 2 ports detected
[17179614.276000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 169
[17179614.276000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[17179614.276000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[17179614.276000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[17179614.276000] uhci_hcd 0000:00:1d.1: irq 169, io base 0x00002460
[17179614.276000] hub 3-0:1.0: USB hub found
[17179614.276000] hub 3-0:1.0: 2 ports detected
[17179614.380000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
[17179614.380000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[17179614.380000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[17179614.380000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[17179614.380000] uhci_hcd 0000:00:1d.2: irq 185, io base 0x00002480
[17179614.380000] hub 4-0:1.0: USB hub found
[17179614.380000] hub 4-0:1.0: 2 ports detected
[17179614.412000] usb 1-1: new high speed USB device using ehci_hcd and address 2
[17179614.556000] Initializing USB Mass Storage driver...
[17179614.608000] Attempting manual resume
[17179614.640000] EXT3-fs: mounted filesystem with ordered data mode.
[17179614.640000] kjournald starting.  Commit interval 5 seconds
[17179614.672000] scsi2 : SCSI emulation for USB Mass Storage devices
[17179614.672000] usb-storage: device found at 2
[17179614.672000] usb-storage: waiting for device to settle before scanning
[17179614.672000] usbcore: registered new driver usb-storage
[17179614.672000] USB Mass Storage support registered.
[17179619.672000]   Vendor: Maxtor    Model: 6Y160P0           Rev: YAR4
[17179619.672000]   Type:   Direct-Access                      ANSI SCSI revision: 02
[17179619.672000] usb-storage: device scan complete
[17179621.604000] Driver 'sd' needs updating - please use bus_type methods
[17179621.604000] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
[17179621.604000] sda: assuming drive cache: write through
[17179621.608000] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
[17179621.608000] sda: assuming drive cache: write through
[17179621.608000]  sda: sda1
[17179621.612000] sd 2:0:0:0: Attached scsi disk sda
[17179621.680000] sd 2:0:0:0: Attached scsi generic sg0 type 0
[17179623.184000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179623.216000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179623.280000] input: PC Speaker as /class/input/input1
[17179623.312000] Linux agpgart interface v0.101 (c) Dave Jones
[17179623.316000] agpgart: Detected an Intel E7505 Chipset.
[17179623.320000] agpgart: AGP aperture is 64M @ 0xf4000000
[17179623.368000] parport: PnPBIOS parport detected.
[17179623.368000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179623.432000] Floppy drive(s): fd0 is 1.44M
[17179623.440000] hw_random: RNG not detected
[17179623.460000] FDC 0 is a post-1991 82077
[17179623.692000] tg3.c:v3.47 (Dec 28, 2005)
[17179623.692000] ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 21 (level, low) -> IRQ 209
[17179623.712000] eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0b:cd:3c:c9:75
[17179623.712000] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] 
[17179623.712000] eth0: dma_rwctrl[763f0000]
[17179623.732000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 217
[17179623.732000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[17179624.008000] input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
[17179624.032000] ts: Compaq touchscreen protocol output
[17179624.052000] intel8x0_measure_ac97_clock: measured 57991 usecs
[17179624.052000] intel8x0: clocking to 48000
[17179624.324000] Intel ISA PCIC probe: not found.
[17179624.416000] lp0: using parport0 (interrupt-driven).
[17179624.504000] Adding 1951888k swap on /dev/hda3.  Priority:-1 extents:1 across:1951888k
[17179624.564000] EXT3 FS on hda1, internal journal
[17179624.780000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179624.780000] md: bitmap version 4.39
[17179625.216000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
[17179625.444000] tg3: eth0: Link is up at 100 Mbps, half duplex.
[17179625.444000] tg3: eth0: Flow control is off for TX and off for RX.
[17179625.772000] cdrom: open failed.
[17179626.272000] kjournald starting.  Commit interval 5 seconds
[17179626.272000] EXT3 FS on hda4, internal journal
[17179626.272000] EXT3-fs: mounted filesystem with ordered data mode.
[17179626.368000] kjournald starting.  Commit interval 5 seconds
[17179626.368000] EXT3 FS on hda2, internal journal
[17179626.368000] EXT3-fs: mounted filesystem with ordered data mode.
[17179626.616000] NET: Registered protocol family 10
[17179626.616000] lo: Disabled Privacy Extensions
[17179626.616000] IPv6 over IPv4 tunneling driver