[Bug 6810] No sound from snd_intel8x0 on Acer4001WLMi Laptop ("semaphore is not ready")

Tue Mar 8 03:05:56 UTC 2005

Please do not reply to this email.  You can add comments at
http://bugzilla.ubuntu.com/show_bug.cgi?id=6810
Ubuntu | linux

------- Additional Comments From jeny6485 at student.uu.se  2005-03-08 03:05 UTC -------
Should probably add that I'm using the newer kernel now: this is the dmesg output:

Linux version 2.6.10-4-686 (buildd at mcmurdo) (gcc version 3.3.5 (Debian
1:3.3.5-8ubuntu2)) #1 Wed Mar 2 06:19:32 UTC 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fee0000 (usable)
 BIOS-e820: 000000001fee0000 - 000000001feec000 (ACPI data)
 BIOS-e820: 000000001feec000 - 000000001ff00000 (ACPI NVS)
 BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
 BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
0MB HIGHMEM available.
510MB LOWMEM available.
On node 0 totalpages: 130784
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 126688 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI present.
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro acpi=off quiet splash
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01403000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1499.277 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510800k/523136k available (1584k kernel code, 11776k reserved, 712k
data, 164k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2965.50 BogoMIPS (lpj=1482752)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 00000180
00000000
CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000 00000180
00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f9bf 00000000 00000000 00000040 00000180 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) M processor 1.50GHz stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like
an initrd
Freeing initrd memory: 4532k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd782, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f6350
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xab76, dseg 0x400
PnPBIOS: 18 nodes reported by PnP BIOS; 18 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX/ICH [8086/24cc] at 0000:00:1f.0
PCI: IRQ 0 for device 0000:00:1f.1 doesn't match PIRQ mask - try
pci=usepirqmaskPCI: Found IRQ 6 for device 0000:00:1f.1
PCI: Sharing IRQ 6 with 0000:00:1d.2
pnp: 00:0a: ioport range 0xfe00-0xfe01 has been reserved
pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0c: ioport range 0x1000-0x105f has been reserved
pnp: 00:0c: ioport range 0x1060-0x107f has been reserved
pnp: 00:0c: ioport range 0x1180-0x11bf has been reserved
audit: initializing netlink socket (disabled)
audit(1110250449.624:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
PCI: Found IRQ 10 for device 0000:00:1f.6
PCI: Sharing IRQ 10 with 0000:00:1f.3
PCI: Sharing IRQ 10 with 0000:00:1f.5
PCI: Sharing IRQ 10 with 0000:02:04.0
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
 Strange, kpnpbiosd not stopped
 Strange, kseriod not stopped
 done
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4532KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 164k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
PCI: Found IRQ 6 for device 0000:00:1f.1
PCI: Sharing IRQ 6 with 0000:00:1d.2
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N060ATMR04-0, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
Probing IDE interface ide1...
hdc: QSI DVDRW SDW-042, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
Adding 497972k swap on /dev/hda5.  Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Synaptics Touchpad, model: 1
 Firmware: 5.9
 Sensor: 18
 new absolute packet format
 Touchpad has extended capability bits
 -> 4 multi-buttons, i.e. besides standard buttons
 -> multifinger detection
 -> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
mice: PS/2 mouse device common for all mice
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
ts: Compaq touchscreen protocol output
lp: driver loaded but no devices found
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel at redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
Real Time Clock Driver v1.12
input: PC Speaker
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855GM Chipset.
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: AGP aperture is 256M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 6 for device 0000:00:1d.0
PCI: Sharing IRQ 6 with 0000:01:00.0
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 6, io base 0x1800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: over-current change on port 1
PCI: Found IRQ 6 for device 0000:00:1d.1
PCI: Sharing IRQ 6 with 0000:02:02.0
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #2
hub 1-0:1.0: over-current change on port 2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 6, io base 0x1820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 6 for device 0000:00:1d.2
PCI: Sharing IRQ 6 with 0000:00:1f.1
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI
Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 6, io base 0x1840
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 10, pci mem 0xd0000000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
hub 4-0:1.0: over-current change on port 1
hub 4-0:1.0: over-current change on port 2
hw_random: RNG not detected
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
PCI: Found IRQ 10 for device 0000:00:1f.6
PCI: Sharing IRQ 10 with 0000:00:1f.3
PCI: Sharing IRQ 10 with 0000:00:1f.5
PCI: Sharing IRQ 10 with 0000:02:04.0
PCI: Setting latency timer of device 0000:00:1f.6 to 64
MC'97 0 converters and GPIO not ready (0x1)
b44.c:v0.95 (Aug 3, 2004)
PCI: Found IRQ 6 for device 0000:02:02.0
PCI: Sharing IRQ 6 with 0000:00:1d.1
eth0: Broadcom 4400 10/100BaseT Ethernet 00:c0:9f:4a:17:21
ieee80211_crypt: registered algorithm 'NULL'
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 0.19
ipw2200: Copyright(c) 2003-2004 Intel Corporation
PCI: Found IRQ 10 for device 0000:02:04.0
PCI: Sharing IRQ 10 with 0000:00:1f.3
PCI: Sharing IRQ 10 with 0000:00:1f.5
PCI: Sharing IRQ 10 with 0000:00:1f.6
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:06.0 (0104 -> 0106)
PCI: Found IRQ 10 for device 0000:02:06.0
PCI: Sharing IRQ 10 with 0000:02:06.2
PCI: Sharing IRQ 10 with 0000:02:06.3
Yenta: CardBus bridge found at 0000:02:06.0 [1025:0064]
Yenta: ISA IRQ mask 0x0ab8, PCI irq 10
Socket status: 30000006
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
PCI: Found IRQ 10 for device 0000:02:06.2
PCI: Sharing IRQ 10 with 0000:02:06.0
PCI: Sharing IRQ 10 with 0000:02:06.3
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10]  MMIO=[d020a000-d020a7ff]  Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00c09f00001fc968]
b44: eth0: Link is down.
NET: Registered protocol family 17
b44: eth0: Link is up at 10 Mbps, half duplex.
b44: eth0: Flow control is off for TX and off for RX.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0312ce0(lo)
IPv6 over IPv4 tunneling driver
apm: BIOS not found.
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg,
GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 431 MBytes.
PCI: Found IRQ 6 for device 0000:01:00.0
PCI: Sharing IRQ 6 with 0000:00:1d.0
[fglrx] module loaded - fglrx 8.8.25 [Jan 14 2005] on minor 0
Fire GL built-in AGP-support
Based on agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 438M
agpgart: Detected an Intel 855PM Chipset, no integrated grapics found.
agpgart: Detected Intel(R) i855PM chipset
agpgart: AGP aperture is 256M @ 0xe0000000
Power management callback for AGP chipset installed
[fglrx] AGP detected, AgpState   = 0x1f000217 (hardware caps of chipset)
AGP: Found 2 AGPv2 devices
AGP: Doing enable for AGPv2
[fglrx] AGP enabled,  AgpCommand = 0x1f000314 (selected caps)
[fglrx] free  AGP = 256126976
[fglrx] max   AGP = 256126976
[fglrx] free  LFB = 53334016
[fglrx] max   LFB = 53334016
[fglrx] free  Inv = 0
[fglrx] max   Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB  = 0
[fglrx] total AGP = 65536
eth0: no IPv6 routers present
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
speedstep-centrino: obtaining ACPI data failed
speedstep-centrino: no table support for CPU model "Intel(R) Pentium(R) M
processor 1.50GHz":
jezze at jezze ~ $

-- 
Configure bugmail: http://bugzilla.ubuntu.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the QA contact for the bug, or are watching the QA contact.