[Bug 670211] [NEW] Stalled boot on Maverick with BeagleBoard
roman
670211 at bugs.launchpad.net
Wed Nov 3 02:08:56 UTC 2010
Public bug reported:
I was not able to run Ubuntu 10.10 on my Beagleboard C4 following the
instructions from https://wiki.ubuntu.com/ARM/OMAPMaverickInstall. Even
after disconnecting all peripherals besides UART boot is freezing. The
serial output is here:
40W
Texas Instruments X-Loader 1.4.4ss (Sep 30 2010 - 14:44:32)
Beagle Rev C4
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2010.09-rc1 (Sep 23 2010 - 11:20:00)
OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 256 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Beagle Rev C4
Die ID #3c5200040000000004036abc08005014
Hit any key to stop autoboot: 0
mmc1 is available
reading boot.scr
323 bytes read
Running bootscript from mmc ...
## Executing script at 82000000
reading uImage
3687812 bytes read
reading uInitrd
6769443 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Ubuntu Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3687748 Bytes = 3.5 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: Ubuntu Initrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6769379 Bytes = 6.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35-22-omap (buildd at gourd) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu4) ) #33-Ubuntu Mon Sep 20 03:17:30 UTC 2010 (Ubuntu 2.6.35-22.33-omap 2.6.35.4)
[ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c0763660, node_mem_map c0820000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: vram=12M omapfb.mode=dvi:1920x1080MR-16 at 60 root=/dev/mmcblk0p2 fixrtc console=ttyS2,115200n8 earlyprintk=ttyS2 loglevel=8
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 1310720 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 128MB 128MB = 256MB total
[ 0.000000] Memory: 231404k/231404k available, 30740k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0044000 ( 240 kB)
[ 0.000000] .text : 0xc0044000 - 0xc06ac000 (6560 kB)
[ 0.000000] .data : 0xc0718000 - 0xc0767960 ( 319 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[ 0.000000] omap_hwmod: l3_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_core_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_per_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP GPIO hardware version 2.5
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 504.17 BogoMIPS (lpj=1970176)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] AppArmor: AppArmor initialized
[ 0.000000] Yama: becoming mindful.
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys ns
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Initializing cgroup subsys memory
[ 0.000000] Initializing cgroup subsys devices
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] mux: Setting signal mcspi1_clk.gpio171 0x011c -> 0x011c
[ 0.000000] mux: Setting signal mcspi1_simo.gpio172 0x011c -> 0x011c
[ 0.000000] mux: Setting signal mcspi1_somi.gpio173 0x011c -> 0x011c
[ 0.000000] OMAP3 Beagle Rev: C4
[ 0.000000] mux: Setting signal i2c3_scl.i2c3_scl 0x0118 -> 0x0100
[ 0.000000] mux: Setting signal i2c3_sda.i2c3_sda 0x0118 -> 0x0100
[ 0.000000] mux: Setting signal etk_clk.hsusb1_stp 0x001b -> 0x0003
[ 0.000000] mux: Setting signal etk_ctl.hsusb1_clk 0x0013 -> 0x0003
[ 0.000000] mux: Setting signal etk_d8.hsusb1_dir 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d9.hsusb1_nxt 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d0.hsusb1_data0 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d1.hsusb1_data1 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d2.hsusb1_data2 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d7.hsusb1_data3 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d4.hsusb1_data4 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d5.hsusb1_data5 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d6.hsusb1_data6 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d3.hsusb1_data7 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d11.hsusb2_stp 0x0013 -> 0x0003
[ 0.000000] mux: Setting signal etk_d10.hsusb2_clk 0x0013 -> 0x0003
[ 0.000000] mux: Setting signal etk_d12.hsusb2_dir 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d13.hsusb2_nxt 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d14.hsusb2_data0 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal etk_d15.hsusb2_data1 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi1_cs3.hsusb2_data2 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_cs1.hsusb2_data3 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_simo.hsusb2_data4 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_somi.hsusb2_data5 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_cs0.hsusb2_data6 0x0113 -> 0x010b
[ 0.000000] mux: Setting signal mcspi2_clk.hsusb2_data7 0x0113 -> 0x010b
[ 0.000000] Found NAND on CS0
[ 0.000000] Registering NAND on CS0
[ 0.000000] mux: Setting signal sdrc_cke0.sdrc_cke0 0x0118 -> 0x0000
[ 0.000000] mux: Setting signal sdrc_cke1.sdrc_cke1 0x0118 -> 0x0000
[ 0.000000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 0.000122] OMAP DMA hardware revision 4.0
[ 0.010711] bio: create slab <bio-0> at 0
[ 0.017059] SCSI subsystem initialized
[ 0.021270] libata version 3.00 loaded.
[ 0.025909] usbcore: registered new interface driver usbfs
[ 0.031768] usbcore: registered new interface driver hub
[ 0.037506] usbcore: registered new device driver usb
[ 0.053375] i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
[ 0.061798] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.067291] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.073608] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.079742] mux: Setting signal etk_d9.gpio23 0x010b -> 0x0104
[ 0.085906] mux: Setting signal etk_d9.gpio23 0x0104 -> 0x011c
[ 0.092193] mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0018 -> 0x0118
[ 0.099182] mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0118 -> 0x0118
[ 0.106109] mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0118 -> 0x0118
[ 0.113250] mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0118 -> 0x0118
[ 0.120361] mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0118 -> 0x0118
[ 0.127471] mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0118 -> 0x0118
[ 0.134582] mux: Setting signal sdmmc1_dat4.sdmmc1_dat4 0x0118 -> 0x0118
[ 0.141693] mux: Setting signal sdmmc1_dat5.sdmmc1_dat5 0x0118 -> 0x0118
[ 0.148803] mux: Setting signal sdmmc1_dat6.sdmmc1_dat6 0x0118 -> 0x0118
[ 0.155914] mux: Setting signal sdmmc1_dat7.sdmmc1_dat7 0x0118 -> 0x0118
[ 0.164123] regulator: VUSB1V5: 1500 mV normal standby
[ 0.169891] regulator: VUSB1V8: 1800 mV normal standby
[ 0.175659] regulator: VUSB3V1: 3100 mV normal standby
[ 0.185089] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.192443] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
[ 0.199920] regulator: VDAC: 1800 mV normal standby
[ 0.205444] regulator: VPLL2: 1800 mV normal standby
[ 0.211181] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
[ 0.218414] i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz
[ 0.225158] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.232421] NetLabel: Initializing
[ 0.236053] NetLabel: domain hash size = 128
[ 0.240631] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.245941] NetLabel: unlabeled traffic allowed by default
[ 0.251831] Switching to clocksource 32k_counter
[ 0.267028] AppArmor: AppArmor Filesystem Enabled
[ 0.285247] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[ 0.292816] musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.303802] musb_hdrc: MHDRC RTL version 1.400
[ 0.308563] musb_hdrc: setup fifo_mode 4
[ 0.312744] musb_hdrc: 28/31 max ep, 16384/16384 memory
[ 0.318450] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[ 0.326965] NET: Registered protocol family 2
[ 0.331878] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.340026] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.347625] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.354522] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.361175] TCP reno registered
[ 0.364501] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.370635] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377471] NET: Registered protocol family 1
[ 0.383087] PMU: registered new PMU device of type 0
[ 0.388366] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.395599] Trying to unpack rootfs image as initramfs...
[ 0.413879] audit: initializing netlink socket (disabled)
[ 0.419616] type=2000 audit(0.890:1): initialized
[ 8.484893] VFS: Disk quotas dquot_6.5.2
[ 8.489440] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.500518] fuse init (API version 7.14)
[ 8.505371] msgmni has been set to 451
[ 8.511383] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 8.519165] io scheduler noop registered
[ 8.523345] io scheduler deadline registered
[ 8.527984] io scheduler cfq registered (default)
[ 8.593017] OMAP DSS rev 2.0
[ 8.596191] OMAP DISPC rev 3.0
[ 8.599456] OMAP VENC rev 2
[ 8.720428] Freeing initrd memory: 6608K
[ 8.945800] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 8.974212] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[ 9.002227] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[ 9.030212] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[ 9.037384] console [ttyS2] enabled, bootconsole disabled
[ 9.037384] console [ttyS2] enabled, bootconsole disabled
[ 9.057312] brd: module loaded
[ 9.064880] loop: module loaded
[ 9.070098] omap2-nand driver initializing
[ 9.074523] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron omap2-nand.0)
[ 9.082275] NAND bus width 8 instead 16 bit
[ 9.086517] No NAND device found.
[ 9.090026] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
[ 9.098724] Creating 5 MTD partitions on "omap2-nand.0":
[ 9.104125] 0x000000000000-0x000000080000 : "X-Loader"
[ 9.111022] 0x000000080000-0x000000260000 : "U-Boot"
[ 9.118255] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 9.125000] 0x000000280000-0x000000680000 : "Kernel"
[ 9.132995] 0x000000680000-0x000010000000 : "File System"
[ 9.246185] Fixed MDIO Bus: probed
[ 9.250061] PPP generic driver version 2.4.2
[ 9.254730] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 9.264495] CSLIP: code copyright 1989 Regents of the University of California.
[ 9.271850] SLIP linefill/keepalive option.
[ 9.276336] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.283233] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 9.289031] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 9.296691] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 9.311584] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 9.318298] hub 1-0:1.0: USB hub found
[ 9.322174] hub 1-0:1.0: 3 ports detected
[ 9.350860] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.357727] mice: PS/2 mouse device common for all mice
[ 9.363708] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 9.370025] twl_rtc twl_rtc: Power up reset detected.
[ 9.376068] twl_rtc twl_rtc: Enabling TWL-RTC.
[ 9.381866] device-mapper: uevent: version 1.0.3
[ 9.387390] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel at redhat.com
[ 9.396270] device-mapper: multipath: version 1.1.1 loaded
[ 9.401855] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 9.409362] cpuidle: using governor ladder
[ 9.413574] cpuidle: using governor menu
[ 9.417602] sdhci: Secure Digital Host Controller Interface driver
[ 9.423858] sdhci: Copyright(c) Pierre Ossman
[ 9.606231] No device for DAI omap-mcbsp-dai-0
[ 9.610748] No device for DAI omap-mcbsp-dai-1
[ 9.615234] No device for DAI omap-mcbsp-dai-2
[ 9.619720] No device for DAI omap-mcbsp-dai-3
[ 9.624237] No device for DAI omap-mcbsp-dai-4
[ 9.628692] Not OMAP3 EVM!
[ 9.631439] OMAP3 Beagle/Devkit8000 SoC init
[ 9.637481] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[ 9.646972] ALSA device list:
[ 9.650054] #0: omap3beagle (twl4030)
[ 9.655334] TCP cubic registered
[ 9.659881] NET: Registered protocol family 10
[ 9.665985] lo: Disabled Privacy Extensions
[ 9.671539] NET: Registered protocol family 17
[ 9.677734] Power Management for TI OMAP3.
[ 9.682800] Disabling unused clock "sr2_fck"
[ 9.687164] Disabling unused clock "sr1_fck"
[ 9.691467] Disabling unused clock "mcbsp4_fck"
[ 9.696075] Disabling unused clock "mcbsp3_fck"
[ 9.700622] Disabling unused clock "mcbsp2_fck"
[ 9.705230] Disabling unused clock "mcbsp4_ick"
[ 9.709808] Disabling unused clock "mcbsp3_ick"
[ 9.714385] Disabling unused clock "mcbsp2_ick"
[ 9.718994] Disabling unused clock "gpt2_ick"
[ 9.723358] Disabling unused clock "gpt3_ick"
[ 9.727783] Disabling unused clock "gpt4_ick"
[ 9.732177] Disabling unused clock "gpt5_ick"
[ 9.736572] Disabling unused clock "gpt6_ick"
[ 9.740966] Disabling unused clock "gpt7_ick"
[ 9.745391] Disabling unused clock "gpt8_ick"
[ 9.749786] Disabling unused clock "gpt9_ick"
[ 9.754180] Disabling unused clock "wdt3_ick"
[ 9.758605] Disabling unused clock "wdt3_fck"
[ 9.763000] Disabling unused clock "gpio2_dbck"
[ 9.767578] Disabling unused clock "gpio3_dbck"
[ 9.772155] Disabling unused clock "gpio4_dbck"
[ 9.776733] Disabling unused clock "gpio5_dbck"
[ 9.781311] Disabling unused clock "gpio6_dbck"
[ 9.785888] Disabling unused clock "gpt9_fck"
[ 9.790313] Disabling unused clock "gpt8_fck"
[ 9.794677] Disabling unused clock "gpt7_fck"
[ 9.799102] Disabling unused clock "gpt6_fck"
[ 9.803497] Disabling unused clock "gpt5_fck"
[ 9.807891] Disabling unused clock "gpt4_fck"
[ 9.812316] Disabling unused clock "gpt3_fck"
[ 9.816711] Disabling unused clock "gpt2_fck"
[ 9.821105] Disabling unused clock "gpt1_ick"
[ 9.825500] Disabling unused clock "wdt1_ick"
[ 9.829925] Disabling unused clock "wdt2_ick"
[ 9.834320] Disabling unused clock "wdt2_fck"
[ 9.838714] Disabling unused clock "gpio1_dbck"
[ 9.843322] Disabling unused clock "gpt1_fck"
[ 9.847717] Disabling unused clock "cam_ick"
[ 9.852050] Disabling unused clock "cam_mclk"
[ 9.856475] Disabling unused clock "des1_ick"
[ 9.860870] Disabling unused clock "sha11_ick"
[ 9.865356] Disabling unused clock "rng_ick"
[ 9.869689] Disabling unused clock "aes1_ick"
[ 9.874084] Disabling unused clock "ssi_ick"
[ 9.878387] Disabling unused clock "mailboxes_ick"
[ 9.883239] Disabling unused clock "mcbsp1_ick"
[ 9.887817] Disabling unused clock "mcbsp5_ick"
[ 9.892395] Disabling unused clock "gpt10_ick"
[ 9.896881] Disabling unused clock "gpt11_ick"
[ 9.901367] Disabling unused clock "i2c2_ick"
[ 9.905792] Disabling unused clock "mcspi1_ick"
[ 9.910339] Disabling unused clock "mcspi2_ick"
[ 9.914947] Disabling unused clock "mcspi3_ick"
[ 9.919494] Disabling unused clock "mcspi4_ick"
[ 9.924102] Disabling unused clock "hdq_ick"
[ 9.928405] Disabling unused clock "mspro_ick"
[ 9.932891] Disabling unused clock "des2_ick"
[ 9.937316] Disabling unused clock "sha12_ick"
[ 9.941772] Disabling unused clock "aes2_ick"
[ 9.946197] Disabling unused clock "icr_ick"
[ 9.950500] Disabling unused clock "pka_ick"
[ 9.954833] Disabling unused clock "ssi_ssr_fck"
[ 9.959472] Disabling unused clock "hdq_fck"
[ 9.963806] Disabling unused clock "mcspi1_fck"
[ 9.968383] Disabling unused clock "mcspi2_fck"
[ 9.972961] Disabling unused clock "mcspi3_fck"
[ 9.977539] Disabling unused clock "mcspi4_fck"
[ 9.982086] Disabling unused clock "mcbsp1_fck"
[ 9.986694] Disabling unused clock "mcbsp5_fck"
[ 9.991271] Disabling unused clock "i2c2_fck"
[ 9.995666] Disabling unused clock "mspro_fck"
[ 10.000152] Disabling unused clock "gpt11_fck"
[ 10.004638] Disabling unused clock "gpt10_fck"
[ 10.009155] Disabling unused clock "sad2d_ick"
[ 10.013641] Disabling unused clock "dpll4_m6x2_ck"
[ 10.018493] Disabling unused clock "dpll3_m3x2_ck"
[ 10.023345] Disabling unused clock "sys_clkout1"
[ 10.028015] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
[ 10.040039] registered taskstats version 1
[ 10.044403] fbcvt: 1920x1080 at 60: CVT Name - 2.073M9-R
[ 10.103881] Console: switching to colour frame buffer device 240x67
[ 10.141540] regulator_init_complete: incomplete constraints, leaving VDAC on
[ 10.149658] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 10.159729] Freeing init memory: 240K
[ 10.163574] mmc0: new high speed SDHC card at address 0001
[ 10.176818] mmcblk0: mmc0:0001 00000 3.79 GiB
[ 10.188049] mmcblk0: p1 p2
Loading, please wait...
[ 10.349700] udev[68]: starting version 163
Begin: Loading essential drivers ... [ 12.267150] Btrfs loaded
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... [ 13.679870] mmcblk0: p1 p2
Resizing root filesystem. Please wait, this will take a moment ...
[ 16.614807] EXT3-fs: barriers not enabled
[ 16.620178] kjournald starting. Commit interval 5 seconds
[ 16.633178] EXT3-fs (mmcblk0p2): using internal journal
[ 16.638458] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
Checking filesystem before resizing... Done.
Resizing, pass: 1 [100/100]
done.
[ 54.814147] EXT3-fs: barriers not enabled
[ 54.819305] kjournald starting. Commit interval 5 seconds
[ 54.825042] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
Begin: Running /scripts/local-bottom ... [ 55.156494] EXT3-fs (mmcblk0p2): using internal journal
detected console= cmdline option, enabling serial console handling
setting up fstab
setting up swap, this will take a moment ...
setting up loopback networking
enabling oem-config
writing flash-kernel.conf
creating boot.script
adding SD card optimizations
setting default session
reboot check
Rebooting into configuration session ...
[ 146.240020] md: stopping all md devices.
[ 147.267761] Restarting system.
40W
Texas Instruments X-Loader 1.4.4ss (Sep 30 2010 - 14:44:32)
Beagle Rev C4
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2010.09-rc1 (Sep 23 2010 - 11:20:00)
OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 256 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Beagle Rev C4
Die ID #3c5200040000000004036abc08005014
Hit any key to stop autoboot: 0
mmc1 is available
reading boot.scr
367 bytes read
Running bootscript from mmc ...
## Executing script at 82000000
reading uImage
3687812 bytes read
reading uInitrd
6769443 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Ubuntu Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3687748 Bytes = 3.5 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: Ubuntu Initrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6769379 Bytes = 6.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
fsck from util-linux-ng 2.17.2
/dev/mmcblk0p2: clean, 118171/462240 files, 534028/975948 blocks
* Starting AppArmor profiles Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox
[ OK ]
* Setting sensors limits [ OK ]
speech-dispatcher disabled; edit /etc/default/speech-dispatcher
fsck from util-linux-ng 2.17.2
/dev/mmcblk0p2: clean, 118171/462240 files, 534028/975948 blocks
* Starting AppArmor profiles Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox
[ OK ]
* Setting sensors limits [ OK ]
* PulseAudio configured for per-user sessions
saned disabled; edit /etc/default/saned
* Enabling additional executable binary formats binfmt-support [ OK ]
** Affects: linux (Ubuntu)
Importance: Undecided
Status: New
--
Stalled boot on Maverick with BeagleBoard
https://bugs.launchpad.net/bugs/670211
You received this bug notification because you are a member of Kernel
Bugs, which is subscribed to linux in ubuntu.
More information about the kernel-bugs
mailing list