[Bug 384724] [NEW] Kyocera sl400r digicam does not work as usb memory

[frederyk]

Public bug reported:

Some years before my Kyocera Digicam was working fine under linux, but
now no Ubuntu can use it to get on the data at the sd-card. Maybe there
is a communication problem between the usb-stack and the camera. The
kernel announces a sdc-device, but no /dev/sdc is coming! Maybe quite a
lot of other old usb-1.1 devices will have the same problem. I have to
use a sd-card-reader. :(


Jun  8 09:57:40 ubuntustation kernel: [  255.796026] usb 2-2: new full speed USB device using uhci_hcd and address 3
Jun  8 09:57:40 ubuntustation kernel: [  255.954058] usb 2-2: configuration #1 chosen from 1 choice
Jun  8 09:57:40 ubuntustation kernel: [  255.958529] scsi4 : SCSI emulation for USB Mass Storage devices
Jun  8 09:57:45 ubuntustation kernel: [  260.972291] scsi 4:0:0:0: Direct-Access     Kyocera  Finecam SL400R   1.00 PQ: 0 ANSI: 2
Jun  8 09:57:45 ubuntustation kernel: [  260.983205] sd 4:0:0:0: [sdc] 1950721 512-byte hardware sectors (999 MB)
Jun  8 09:57:45 ubuntustation kernel: [  260.986222] sd 4:0:0:0: [sdc] Write Protect is off
Jun  8 09:57:45 ubuntustation kernel: [  260.999271] sd 4:0:0:0: [sdc] 1950721 512-byte hardware sectors (999 MB)
Jun  8 09:57:45 ubuntustation kernel: [  261.002236] sd 4:0:0:0: [sdc] Write Protect is off
Jun  8 09:57:45 ubuntustation kernel: [  261.002308]  sdc: sdc1
Jun  8 09:57:45 ubuntustation kernel: [  261.013718] sd 4:0:0:0: [sdc] Attached SCSI removable disk
Jun  8 09:57:45 ubuntustation kernel: [  261.014078] sd 4:0:0:0: Attached scsi generic sg4 type 0
Jun  8 09:58:15 ubuntustation kernel: [  291.372042] usb 2-2: reset full speed USB device using uhci_hcd and address 3
Jun  8 09:58:46 ubuntustation kernel: [  321.916101] usb 2-2: reset full speed USB device using uhci_hcd and address 3
Jun  8 09:59:16 ubuntustation kernel: [  352.460052] usb 2-2: reset full speed USB device using uhci_hcd and address 3
Jun  8 09:59:27 ubuntustation kernel: [  362.820097] usb 2-2: reset full speed USB device using uhci_hcd and address 3
Jun  8 09:59:37 ubuntustation kernel: [  373.068116] usb 2-2: USB disconnect, address 3
Jun  8 09:59:37 ubuntustation kernel: [  373.070815] scsi 4:0:0:0: Device offlined - not ready after error recovery
Jun  8 09:59:37 ubuntustation kernel: [  373.073423] scsi 4:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
Jun  8 09:59:37 ubuntustation kernel: [  373.073468] __ratelimit: 61 callbacks suppressed
Jun  8 09:59:37 ubuntustation kernel: [  373.180045] usb 2-2: new full speed USB device using uhci_hcd and address 4
Jun  8 10:00:08 ubuntustation kernel: [  403.724084] usb 2-2: new full speed USB device using uhci_hcd and address 5

** Affects: linux-meta (Ubuntu)
     Importance: Undecided
         Status: New


** Tags: 1.1 kernel problem usb

-- 
Kyocera sl400r digicam does not work as usb memory
https://bugs.launchpad.net/bugs/384724
You received this bug notification because you are a member of Kernel
Bugs, which is subscribed to linux-meta in ubuntu.