[Bug 60963] Re: SGS Thomson 5in1 card reader not mounting sd
MMeija
mmeija at tripleblack.net
Mon Sep 18 06:43:02 UTC 2006
** Description changed:
Binary package hint: linux-source-2.6.15
i'm not able to use my sd-flash reader in ubuntu; other operating systems handle it well
hasn't worked in dapper.. i can't recall if i tried breezy
i put an sd card in, the card reader light will light up for a bit and then turn off;
i suppose this is an obscure device..
laptop is an acer ferrari 3400
thanks for your time
Linux ferrari 2.6.15-26-686 #1 SMP PREEMPT Fri Sep 8 20:16:40 UTC 2006
i686 GNU/Linux
-
- root at ferrari:~# lsusb
- Bus 004 Device 002: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0 "TetraHub"
- Bus 004 Device 001: ID 0000:0000
- Bus 001 Device 001: ID 0000:0000
- Bus 003 Device 002: ID 0483:0321 SGS Thomson Microelectronics
- Bus 003 Device 001: ID 0000:0000
- Bus 002 Device 001: ID 0000:0000
-
- dmesg:
- [17179569.184000] Linux version 2.6.15-26-686 (buildd at terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Fri Sep 8 20:16:40 UTC 2006
- [17179569.184000] BIOS-provided physical RAM map:
- [17179569.184000] BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
- [17179569.184000] BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
- [17179569.184000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
- [17179569.184000] BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
- [17179569.184000] BIOS-e820: 000000001fef0000 - 000000001fefa000 (ACPI data)
- [17179569.184000] BIOS-e820: 000000001fefa000 - 000000001ff00000 (ACPI NVS)
- [17179569.184000] BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
- [17179569.184000] BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
- [17179569.184000] 0MB HIGHMEM available.
- [17179569.184000] 510MB LOWMEM available.
- [17179569.184000] found SMP MP-table at 000f68f0
- [17179569.184000] On node 0 totalpages: 130800
- [17179569.184000] DMA zone: 4096 pages, LIFO batch:0
- [17179569.184000] DMA32 zone: 0 pages, LIFO batch:0
- [17179569.184000] Normal zone: 126704 pages, LIFO batch:31
- [17179569.184000] HighMem zone: 0 pages, LIFO batch:0
- [17179569.184000] DMI 2.3 present.
- [17179569.184000] ACPI: RSDP (v000 PTLTD ) @ 0x000f6950
- [17179569.184000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fef43e3
- [17179569.184000] ACPI: FADT (v001 AMDK8 PTLTW 0x06040000 PTL_ 0x000f4240) @ 0x1fef9e1d
- [17179569.184000] ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1fef9e91
- [17179569.184000] ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x1fef9f88
- [17179569.184000] ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1fef9fd8
- [17179569.184000] ACPI: DSDT (v001 VIA PTL_ACPI 0x06040000 MSFT 0x0100000e) @ 0x00000000
- [17179569.184000] ACPI: PM-Timer IO Port: 0x4008
- [17179569.184000] ACPI: Local APIC address 0xfee00000
- [17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
- [17179569.184000] Processor #0 15:12 APIC version 16
- [17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
- [17179569.184000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
- [17179569.184000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
- [17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
- [17179569.184000] ACPI: IRQ0 used by override.
- [17179569.184000] ACPI: IRQ2 used by override.
- [17179569.184000] ACPI: IRQ10 used by override.
- [17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
- [17179569.184000] Using ACPI (MADT) for SMP configuration information
- [17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dffe0000)
- [17179569.184000] Built 1 zonelists
- [17179569.184000] Kernel command line: root=/dev/hda1 ro quiet splash
- [17179569.184000] mapped APIC to ffffd000 (fee00000)
- [17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
- [17179569.184000] Initializing CPU#0
- [17179569.184000] PID hash table entries: 2048 (order: 11, 32768 bytes)
- [17179569.184000] Detected 2004.831 MHz processor.
- [17179569.184000] Using pmtmr for high-res timesource
- [17179569.184000] Console: colour VGA+ 80x25
- [17179569.524000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
- [17179569.524000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
- [17179569.532000] Memory: 506968k/523200k available (2115k kernel code, 15576k reserved, 595k data, 332k init, 0k highmem)
- [17179569.532000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
- [17179569.612000] Calibrating delay using timer specific routine.. 4014.07 BogoMIPS (lpj=8028149)
- [17179569.612000] Security Framework v1.0.0 initialized
- [17179569.612000] SELinux: Disabled at boot.
- [17179569.612000] Mount-cache hash table entries: 512
- [17179569.612000] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000
- [17179569.612000] CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000
- [17179569.612000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
- [17179569.612000] CPU: L2 Cache: 512K (64 bytes/line)
- [17179569.612000] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000000 00000000 00000000
- [17179569.612000] mtrr: v2.0 (20020519)
- [17179569.612000] Enabling fast FPU save and restore... done.
- [17179569.612000] Enabling unmasked SIMD FPU exception support... done.
- [17179569.612000] Checking 'hlt' instruction... OK.
- [17179569.628000] SMP alternatives: switching to UP code
- [17179569.628000] checking if image is initramfs... it is
- [17179570.136000] Freeing initrd memory: 6809k freed
- [17179570.144000] ACPI: Looking for DSDT ... not found!
- [17179570.148000] CPU0: AMD Mobile AMD Athlon 64 Processor 3000+ stepping 00
- [17179570.148000] Total of 1 processors activated (4014.07 BogoMIPS).
- [17179570.148000] ENABLING IO-APIC IRQs
- [17179570.148000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
- [17179570.292000] Brought up 1 CPUs
- [17179570.292000] NET: Registered protocol family 16
- [17179570.292000] EISA bus registered
- [17179570.292000] ACPI: bus type pci registered
- [17179570.292000] PCI: PCI BIOS revision 2.10 entry at 0xfd64c, last bus=1
- [17179570.292000] PCI: Using configuration type 1
- [17179570.292000] ACPI: Subsystem revision 20051216
- [17179570.292000] ACPI: Interpreter enabled
- [17179570.292000] ACPI: Using IOAPIC for interrupt routing
- [17179570.292000] ACPI: PCI Root Bridge [PCI0] (0000:00)
- [17179570.292000] PCI: Probing PCI hardware (bus 00)
- [17179570.296000] PCI quirk: region 4000-407f claimed by vt8235 PM
- [17179570.296000] PCI quirk: region 8100-810f claimed by vt8235 SMB
- [17179570.296000] Boot video device is 0000:01:00.0
- [17179570.296000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
- [17179570.300000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
- [17179570.300000] ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *5, disabled.
- [17179570.300000] ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *9, disabled.
- [17179570.300000] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled.
- [17179570.300000] ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *5, disabled.
- [17179570.300000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 12 14 15)
- [17179570.300000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 12 14 15) *9
- [17179570.300000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *11 12 14 15)
- [17179570.300000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15)
- [17179570.300000] ACPI: Embedded Controller [EC0] (gpe 1) interrupt mode.
- [17179570.312000] Linux Plug and Play Support v0.97 (c) Adam Belay
- [17179570.312000] pnp: PnP ACPI init
- [17179570.312000] pnp: PnP ACPI: found 9 devices
- [17179570.312000] PnPBIOS: Disabled by ACPI PNP
- [17179570.312000] PCI: Using ACPI for IRQ routing
- [17179570.312000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
- [17179570.316000] pnp: 00:05: ioport range 0x600-0x60f has been reserved
- [17179570.316000] pnp: 00:05: ioport range 0x4d0-0x4d1 has been reserved
- [17179570.316000] pnp: 00:05: ioport range 0xfe10-0xfe11 could not be reserved
- [17179570.316000] pnp: 00:05: ioport range 0xfe00-0xfe00 has been reserved
- [17179570.316000] PCI: Bridge: 0000:00:01.0
- [17179570.316000] IO window: 2000-2fff
- [17179570.316000] MEM window: d0100000-d01fffff
- [17179570.316000] PREFETCH window: d8000000-dfffffff
- [17179570.316000] PCI: Bus 2, cardbus bridge: 0000:00:07.0
- [17179570.316000] IO window: 00001c00-00001cff
- [17179570.316000] IO window: 00003000-000030ff
- [17179570.316000] PREFETCH window: 30000000-31ffffff
- [17179570.316000] MEM window: 32000000-33ffffff
- [17179570.316000] PCI: Setting latency timer of device 0000:00:01.0 to 64
- [17179570.316000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 169
- [17179570.316000] PCI: Setting latency timer of device 0000:00:07.0 to 64
- [17179570.316000] Simple Boot Flag at 0x37 set to 0x1
- [17179570.316000] audit: initializing netlink socket (disabled)
- [17179570.316000] audit(1158491693.312:1): initialized
- [17179570.316000] VFS: Disk quotas dquot_6.5.1
- [17179570.316000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [17179570.316000] Initializing Cryptographic API
- [17179570.316000] io scheduler noop registered
- [17179570.316000] io scheduler anticipatory registered
- [17179570.316000] io scheduler deadline registered
- [17179570.316000] io scheduler cfq registered
- [17179570.316000] isapnp: Scanning for PnP cards...
- [17179570.672000] isapnp: No Plug & Play device found
- [17179570.684000] Real Time Clock Driver v1.12
- [17179570.684000] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
- [17179570.684000] serio: i8042 AUX port at 0x60,0x64 irq 12
- [17179570.684000] serio: i8042 KBD port at 0x60,0x64 irq 1
- [17179570.684000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
- [17179570.688000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
- [17179570.688000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
- [17179570.688000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
- [17179570.688000] mice: PS/2 mouse device common for all mice
- [17179570.688000] EISA: Probing bus 0 at eisa.0
- [17179570.688000] Cannot allocate resource for EISA slot 1
- [17179570.688000] Cannot allocate resource for EISA slot 2
- [17179570.688000] Cannot allocate resource for EISA slot 3
- [17179570.688000] Cannot allocate resource for EISA slot 4
- [17179570.688000] EISA: Detected 0 cards.
- [17179570.688000] NET: Registered protocol family 2
- [17179570.724000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
- [17179570.724000] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
- [17179570.724000] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
- [17179570.724000] TCP: Hash tables configured (established 16384 bind 16384)
- [17179570.724000] TCP reno registered
- [17179570.724000] TCP bic registered
- [17179570.724000] NET: Registered protocol family 1
- [17179570.724000] NET: Registered protocol family 8
- [17179570.724000] NET: Registered protocol family 20
- [17179570.724000] Using IPI No-Shortcut mode
- [17179570.724000] ACPI wakeup devices:
- [17179570.724000] PCI0 USB1 USB2 USB3 GIGA Z000
- [17179570.724000] ACPI: (supports S0 S3 S4 S5)
- [17179570.724000] Freeing unused kernel memory: 332k freed
- [17179570.728000] input: AT Translated Set 2 keyboard as /class/input/input0
- [17179570.760000] vga16fb: initializing
- [17179570.760000] vga16fb: mapped to 0xc00a0000
- [17179570.864000] Console: switching to colour frame buffer device 80x25
- [17179570.864000] fb0: VGA16 VGA frame buffer device
- [17179571.932000] Capability LSM initialized
- [17179572.060000] ACPI: CPU0 (power states: C1[C1] C2[C2])
- [17179572.064000] ACPI: Thermal Zone [THRM] (47 C)
- [17179572.480000] VP_IDE: IDE controller at PCI slot 0000:00:11.1
- [17179572.480000] ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
- [17179572.480000] VP_IDE: chipset revision 6
- [17179572.480000] VP_IDE: not 100% native mode: will probe irqs later
- [17179572.480000] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
- [17179572.480000] ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
- [17179572.480000] ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
- [17179572.480000] Probing IDE interface ide0...
- [17179572.900000] hda: IC25N080ATMR04-0, ATA DISK drive
- [17179573.572000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
- [17179573.596000] Probing IDE interface ide1...
- [17179574.460000] hdc: MATSHITADVD-RAM UJ-835S, ATAPI CD/DVD-ROM drive
- [17179574.796000] ide1 at 0x170-0x177,0x376 on irq 15
- [17179574.800000] hda: max request size: 1024KiB
- [17179574.808000] hda: 156301488 sectors (80026 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
- [17179574.808000] hda: cache flushes supported
- [17179574.808000] hda: hda1 hda2 hda3
- [17179574.844000] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
- [17179574.844000] Uniform CD-ROM driver Revision: 3.20
- [17179575.236000] ieee1394: Initialized config rom entry `ip1394'
- [17179575.244000] usbcore: registered new driver usbfs
- [17179575.244000] usbcore: registered new driver hub
- [17179575.248000] USB Universal Host Controller Interface driver v2.3
- [17179575.248000] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 177
- [17179575.248000] PCI: VIA IRQ fixup for 0000:00:10.0, from 0 to 1
- [17179575.248000] uhci_hcd 0000:00:10.0: UHCI Host Controller
- [17179575.248000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
- [17179575.248000] uhci_hcd 0000:00:10.0: irq 177, io base 0x00001800
- [17179575.248000] hub 1-0:1.0: USB hub found
- [17179575.248000] hub 1-0:1.0: 2 ports detected
- [17179575.312000] ohci1394: $Rev: 1313 $ Ben Collins <bcollins at debian.org>
- [17179575.312000] ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 18 (level, low) -> IRQ 185
- [17179575.352000] ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 177
- [17179575.352000] PCI: VIA IRQ fixup for 0000:00:10.1, from 0 to 1
- [17179575.352000] uhci_hcd 0000:00:10.1: UHCI Host Controller
- [17179575.352000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
- [17179575.352000] uhci_hcd 0000:00:10.1: irq 177, io base 0x00001820
- [17179575.352000] hub 2-0:1.0: USB hub found
- [17179575.352000] hub 2-0:1.0: 2 ports detected
- [17179575.360000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[185] MMIO=[d0015000-d00157ff] Max Packet=[2048]
- [17179575.456000] ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 177
- [17179575.456000] PCI: VIA IRQ fixup for 0000:00:10.2, from 0 to 1
- [17179575.456000] uhci_hcd 0000:00:10.2: UHCI Host Controller
- [17179575.456000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
- [17179575.456000] uhci_hcd 0000:00:10.2: irq 177, io base 0x00001840
- [17179575.456000] hub 3-0:1.0: USB hub found
- [17179575.456000] hub 3-0:1.0: 2 ports detected
- [17179575.560000] ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 177
- [17179575.560000] ehci_hcd 0000:00:10.3: EHCI Host Controller
- [17179575.560000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
- [17179575.560000] ehci_hcd 0000:00:10.3: irq 177, io mem 0xd0015800
- [17179575.560000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
- [17179575.560000] hub 4-0:1.0: USB hub found
- [17179575.560000] hub 4-0:1.0: 6 ports detected
- [17179575.592000] usb 1-1: new full speed USB device using uhci_hcd and address 2
- [17179575.848000] Attempting manual resume
- [17179575.904000] EXT3-fs: INFO: recovery required on readonly filesystem.
- [17179575.904000] EXT3-fs: write access will be enabled during recovery.
- [17179576.536000] usb 4-1: new high speed USB device using ehci_hcd and address 2
- [17179576.632000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f00004fe9cf]
- [17179576.668000] hub 4-1:1.0: USB hub found
- [17179576.668000] hub 4-1:1.0: 4 ports detected
- [17179577.312000] usb 3-1: new full speed USB device using uhci_hcd and address 2
- [17179577.464000] SCSI subsystem initialized
- [17179577.464000] Initializing USB Mass Storage driver...
- [17179577.464000] scsi0 : SCSI emulation for USB Mass Storage devices
- [17179577.464000] usb-storage: device found at 2
- [17179577.464000] usb-storage: waiting for device to settle before scanning
- [17179577.464000] usbcore: registered new driver usb-storage
- [17179577.464000] USB Mass Storage support registered.
- [17179577.508000] EXT3-fs: hda1: orphan cleanup on readonly fs
- [17179577.508000] kjournald starting. Commit interval 5 seconds
- [17179577.556000] ext3_orphan_cleanup: deleting unreferenced inode 2879291
- [17179577.556000] ext3_orphan_cleanup: deleting unreferenced inode 1897467
- [17179577.556000] ext3_orphan_cleanup: deleting unreferenced inode 2878966
- [17179577.588000] ext3_orphan_cleanup: deleting unreferenced inode 2878927
- [17179577.588000] EXT3-fs: hda1: 4 orphan inodes deleted
- [17179577.588000] EXT3-fs: recovery complete.
- [17179577.948000] EXT3-fs: mounted filesystem with ordered data mode.
- [17179582.468000] Vendor: Generic Model: Flash R/W Rev: 2002
- [17179582.468000] Type: Direct-Access ANSI SCSI revision: 02
- [17179582.468000] usb-storage: device scan complete
- [17179590.740000] Driver 'sd' needs updating - please use bus_type methods
- [17179590.756000] sd 0:0:0:0: Attached scsi removable disk sda
- [17179590.764000] sd 0:0:0:0: Attached scsi generic sg0 type 0
- [17179591.980000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
- [17179592.016000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
- [17179592.032000] Linux agpgart interface v0.101 (c) Dave Jones
- [17179592.064000] agpgart: Detected AGP bridge 0
- [17179592.076000] agpgart: AGP aperture is 256M @ 0xe0000000
- [17179592.112000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 169
- [17179592.112000] Yenta: CardBus bridge found at 0000:00:07.0 [1025:0057]
- [17179592.112000] Yenta: Using CSCINT to route CSC interrupts to PCI
- [17179592.112000] Yenta: Routing CardBus interrupts to PCI
- [17179592.112000] Yenta TI: socket 0000:00:07.0, mfunc 0x007c1b22, devctl 0x44
- [17179592.148000] ieee80211_1_1_13_crypt: registered algorithm 'NULL'
- [17179592.168000] ieee80211_1_1_13: 802.11 data/management/control stack, 1.1.13
- [17179592.168000] ieee80211_1_1_13: Copyright (C) 2004-2005 Intel Corporation <jketreno at linux.intel.com>
- [17179592.176000] ieee80211_crypt: registered algorithm 'NULL'
- [17179592.176000] ieee80211: 802.11 data/management/control stack, git-1.1.7
- [17179592.176000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno at linux.intel.com>
- [17179592.344000] Yenta: ISA IRQ mask 0x0af8, PCI irq 169
- [17179592.344000] Socket status: 30000086
- [17179592.572000] tg3.c:v3.47 (Dec 28, 2005)
- [17179592.572000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 169
- [17179592.596000] eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:c0:9f:93:5d:0b
- [17179592.596000] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
- [17179592.596000] eth0: dma_rwctrl[763f0000]
- [17179592.648000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.1
- [17179592.648000] ipw2200: Copyright(c) 2003-2006 Intel Corporation
- [17179592.648000] Warning: PCI driver ipw2200 has a struct device_driver shutdown method, please update!
- [17179592.648000] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 193
- [17179592.648000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
- [17179592.724000] input: PC Speaker as /class/input/input1
- [17179592.860000] Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006
- [17179592.896000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
- [17179593.096000] irda_init()
- [17179593.096000] NET: Registered protocol family 23
- [17179593.108000] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
- [17179593.188000] ts: Compaq touchscreen protocol output
- [17179593.416000] cs: IO port probe 0x100-0x3af: clean.
- [17179593.416000] cs: IO port probe 0x3e0-0x4ff: clean.
- [17179593.420000] cs: IO port probe 0x820-0x8ff: clean.
- [17179593.420000] cs: IO port probe 0xc00-0xcf7: clean.
- [17179593.420000] cs: IO port probe 0xa00-0xaff: clean.
- [17179593.708000] ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 201
- [17179593.716000] PCI: Setting latency timer of device 0000:00:11.6 to 64
- [17179593.740000] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 201
- [17179593.740000] PCI: Setting latency timer of device 0000:00:11.5 to 64
- [17179594.896000] lp: driver loaded but no devices found
- [17179594.924000] sbp2: $Rev: 1306 $ Ben Collins <bcollins at debian.org>
- [17179594.924000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
- [17179594.924000] ieee1394: sbp2: Try serialize_io=0 for better performance
- [17179595.308000] EXT3 FS on hda1, internal journal
- [17179595.544000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
- [17179595.544000] md: bitmap version 4.39
- [17179596.140000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
- [17179597.392000] HFS+-fs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only.
- [17179598.924000] Adding 524280k swap on /mnt/512Mb.swap. Priority:-1 extents:150 across:536004k
- [17179600.292000] ACPI: AC Adapter [ACAD] (on-line)
- [17179600.296000] ACPI: Battery Slot [BAT1] (battery present)
- [17179600.360000] ACPI: Power Button (FF) [PWRF]
- [17179600.360000] ACPI: Power Button (CM) [PWRB]
- [17179600.360000] ACPI: Lid Switch [LID]
- [17179600.360000] ACPI: Sleep Button (CM) [SLPB]
- [17179600.436000] ibm_acpi: ec object not found
- [17179600.464000] pcc_acpi: loading...
- [17179600.540000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
- [17179601.044000] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
- [17179601.044000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
- [17179601.044000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xc (1250 mV)
- [17179601.044000] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0xe (1200 mV)
- [17179601.044000] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x17 (975 mV)
- [17179601.044000] cpu_init done, current fid 0xc, vid 0x8
- [17179606.280000] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
- [17179606.284000] [fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes.
- [17179606.284000] [fglrx] module loaded - fglrx 8.25.18 [May 18 2006] on minor 0
- [17179606.412000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 209
- [17179608.368000] [fglrx:drm_parse_option] *ERROR* "agplock" is not a valid option
- [17179608.368000] [fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes.
- [17179608.368000] [fglrx] AGP detected, AgpState = 0x1f000a0b (hardware caps of chipset)
- [17179608.368000] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
- [17179608.368000] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
- [17179608.368000] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
- [17179608.368000] [fglrx] AGP enabled, AgpCommand = 0x1f000302 (selected caps)
- [17179608.376000] [fglrx] total GART = 268435456
- [17179608.376000] [fglrx] free GART = 252440576
- [17179608.376000] [fglrx] max single GART = 252440576
- [17179608.376000] [fglrx] total LFB = 126169088
- [17179608.376000] [fglrx] free LFB = 114274304
- [17179608.376000] [fglrx] max single LFB = 114274304
- [17179608.376000] [fglrx] total Inv = 0
- [17179608.376000] [fglrx] free Inv = 0
- [17179608.376000] [fglrx] max single Inv = 0
- [17179608.376000] [fglrx] total TIM = 0
- [17179608.492000] ppdev: user-space parallel port driver
- [17179608.684000] [fglrx] total GART = 268435456
- [17179608.684000] [fglrx] free GART = 252440576
- [17179608.684000] [fglrx] max single GART = 252440576
- [17179608.684000] [fglrx] total LFB = 126169088
- [17179608.684000] [fglrx] free LFB = 102719488
- [17179608.684000] [fglrx] max single LFB = 102719488
- [17179608.684000] [fglrx] total Inv = 0
- [17179608.684000] [fglrx] free Inv = 0
- [17179608.684000] [fglrx] max single Inv = 0
- [17179608.684000] [fglrx] total TIM = 0
- [17179609.436000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
- [17179609.436000] apm: overridden by ACPI.
- [17179615.364000] tg3: eth0: Link is up at 100 Mbps, full duplex.
- [17179615.364000] tg3: eth0: Flow control is off for TX and off for RX.
- [17179618.328000] NET: Registered protocol family 17
- [17179619.092000] NET: Registered protocol family 10
- [17179619.092000] lo: Disabled Privacy Extensions
- [17179619.092000] IPv6 over IPv4 tunneling driver
- [17179619.872000] Bluetooth: Core ver 2.8
- [17179619.872000] NET: Registered protocol family 31
- [17179619.872000] Bluetooth: HCI device and connection manager initialized
- [17179619.872000] Bluetooth: HCI socket layer initialized
- [17179619.928000] Bluetooth: L2CAP ver 2.8
- [17179619.928000] Bluetooth: L2CAP socket layer initialized
- [17179620.108000] Bluetooth: RFCOMM socket layer initialized
- [17179620.108000] Bluetooth: RFCOMM TTY layer initialized
- [17179620.108000] Bluetooth: RFCOMM ver 1.7
- [17179620.876000] /dev/vmmon[5113]: Module vmmon: registered with major=10 minor=165
- [17179620.876000] /dev/vmmon[5113]: Module vmmon: initialized
- [17179621.148000] /dev/vmnet: open called by PID 5139 (vmnet-bridge)
- [17179621.148000] /dev/vmnet: hub 0 does not exist, allocating memory.
- [17179621.148000] /dev/vmnet: port on hub 0 successfully opened
- [17179621.148000] bridge-eth0: enabling the bridge
- [17179621.148000] bridge-eth0: up
- [17179621.148000] bridge-eth0: already up
- [17179621.148000] bridge-eth0: attached
- [17179621.172000] /dev/vmnet: open called by PID 5154 (vmnet-netifup)
- [17179621.172000] /dev/vmnet: hub 1 does not exist, allocating memory.
- [17179621.176000] /dev/vmnet: port on hub 1 successfully opened
- [17179621.180000] /dev/vmnet: open called by PID 5155 (vmnet-netifup)
- [17179621.180000] /dev/vmnet: hub 8 does not exist, allocating memory.
- [17179621.180000] /dev/vmnet: port on hub 8 successfully opened
- [17179621.312000] /dev/vmnet: open called by PID 5153 (vmnet-natd)
- [17179621.312000] /dev/vmnet: port on hub 8 successfully opened
- [17179621.684000] /dev/vmnet: open called by PID 5172 (vmnet-dhcpd)
- [17179621.684000] /dev/vmnet: port on hub 8 successfully opened
- [17179621.688000] /dev/vmnet: open called by PID 5177 (vmnet-dhcpd)
- [17179621.688000] /dev/vmnet: port on hub 1 successfully opened
- [17179629.332000] eth1: no IPv6 routers present
- [17179631.460000] vmnet8: no IPv6 routers present
- [17179631.848000] vmnet1: no IPv6 routers present
- [17179632.132000] eth0: no IPv6 routers present
- [17211134.608000] SCSI device sda: 1953792 512-byte hdwr sectors (1000 MB)
- [17211134.612000] sda: Write Protect is off
- [17211134.612000] sda: Mode Sense: 03 00 00 00
- [17211134.612000] sda: assuming drive cache: write through
- [17211134.624000] SCSI device sda: 1953792 512-byte hdwr sectors (1000 MB)
- [17211134.628000] sda: Write Protect is off
- [17211134.628000] sda: Mode Sense: 03 00 00 00
- [17211134.628000] sda: assuming drive cache: write through
- [17211134.628000] sda: sda1
- [17211165.216000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
- [17211165.464000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
- [17211165.712000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
- [17211165.960000] usb 3-1: reset full speed USB device using uhci_hcd and address 2
- [17211166.092000] sd 0:0:0:0: scsi: Device offlined - not ready after error recovery
- [17211166.092000] sd 0:0:0:0: SCSI error: return code = 0x50000
- [17211166.092000] end_request: I/O error, dev sda, sector 1953785
- [17211166.092000] Buffer I/O error on device sda1, logical block 1953656
- [17211166.092000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.092000] Buffer I/O error on device sda1, logical block 1953657
- [17211166.092000] Buffer I/O error on device sda1, logical block 1953658
- [17211166.092000] Buffer I/O error on device sda1, logical block 1953659
- [17211166.092000] Buffer I/O error on device sda1, logical block 1953660
- [17211166.092000] Buffer I/O error on device sda1, logical block 1953661
- [17211166.092000] Buffer I/O error on device sda1, logical block 1953662
- [17211166.092000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.096000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.096000] Buffer I/O error on device sda1, logical block 1953656
- [17211166.096000] Buffer I/O error on device sda1, logical block 1953657
- [17211166.096000] Buffer I/O error on device sda1, logical block 1953658
- [17211166.096000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
- [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device
-
-
- lsusb -vv
-
- Bus 004 Device 002: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0 "TetraHub"
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 2.00
- bDeviceClass 9 Hub
- bDeviceSubClass 0 Unused
- bDeviceProtocol 2 TT per port
- bMaxPacketSize0 64
- idVendor 0x04b4 Cypress Semiconductor Corp.
- idProduct 0x6560 CY7C65640 USB-2.0 "TetraHub"
- bcdDevice 0.09
- iManufacturer 0
- iProduct 0
- iSerial 0
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 41
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 100mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0 Unused
- bInterfaceProtocol 1 Single TT
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0001 1x 1 bytes
- bInterval 12
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 1
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0 Unused
- bInterfaceProtocol 2 TT per port
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0001 1x 1 bytes
- bInterval 12
- Hub Descriptor:
- bLength 9
- bDescriptorType 41
- nNbrPorts 4
- wHubCharacteristic 0x0089
- Per-port power switching
- Per-port overcurrent protection
- TT think time 8 FS bits
- Port indicators
- bPwrOn2PwrGood 50 * 2 milli seconds
- bHubContrCurrent 100 milli Ampere
- DeviceRemovable 0x58
- PortPwrCtrlMask 0xc0
- Hub Port Status:
- Port 1: 0000.0100 power
- Port 2: 0000.0100 power
- Port 3: 0000.0100 power
- Port 4: 0000.0100 power
- Device Qualifier (for other device speed):
- bLength 10
- bDescriptorType 6
- bcdUSB 2.00
- bDeviceClass 9 Hub
- bDeviceSubClass 0 Unused
- bDeviceProtocol 0
- bMaxPacketSize0 64
- bNumConfigurations 1
- Device Status: 0x0001
- Self Powered
-
- Bus 004 Device 001: ID 0000:0000
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 2.00
- bDeviceClass 9 Hub
- bDeviceSubClass 0 Unused
- bDeviceProtocol 1 Single TT
- bMaxPacketSize0 64
- idVendor 0x0000
- idProduct 0x0000
- bcdDevice 2.06
- iManufacturer 3 Linux 2.6.15-26-686 ehci_hcd
- iProduct 2 EHCI Host Controller
- iSerial 1 0000:00:10.3
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 25
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xc0
- Self Powered
- MaxPower 0mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0 Unused
- bInterfaceProtocol 0
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0002 1x 2 bytes
- bInterval 12
- Hub Descriptor:
- bLength 9
- bDescriptorType 41
- nNbrPorts 6
- wHubCharacteristic 0x000a
- No power switching (usb 1.0)
- Per-port overcurrent protection
- TT think time 8 FS bits
- bPwrOn2PwrGood 10 * 2 milli seconds
- bHubContrCurrent 0 milli Ampere
- DeviceRemovable 0x48
- PortPwrCtrlMask 0xc0
- Hub Port Status:
- Port 1: 0000.0503 highspeed power enable connect
- Port 2: 0000.0100 power
- Port 3: 0000.0100 power
- Port 4: 0000.0100 power
- Port 5: 0000.0000
- Port 6: 0000.0100 power
- Device Status: 0x0001
- Self Powered
-
- Bus 001 Device 001: ID 0000:0000
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 1.10
- bDeviceClass 9 Hub
- bDeviceSubClass 0 Unused
- bDeviceProtocol 0
- bMaxPacketSize0 64
- idVendor 0x0000
- idProduct 0x0000
- bcdDevice 2.06
- iManufacturer 3 Linux 2.6.15-26-686 uhci_hcd
- iProduct 2 UHCI Host Controller
- iSerial 1 0000:00:10.0
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 25
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 0mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0 Unused
- bInterfaceProtocol 0
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0002 1x 2 bytes
- bInterval 255
- Hub Descriptor:
- bLength 9
- bDescriptorType 41
- nNbrPorts 2
- wHubCharacteristic 0x000a
- No power switching (usb 1.0)
- Per-port overcurrent protection
- bPwrOn2PwrGood 1 * 2 milli seconds
- bHubContrCurrent 0 milli Ampere
- DeviceRemovable 0x08
- PortPwrCtrlMask 0x82
- Hub Port Status:
- Port 1: 0000.0100 power
- Port 2: 0000.0100 power
- Device Status: 0x0003
- Self Powered
- Remote Wakeup Enabled
-
- Bus 003 Device 002: ID 0483:0321 SGS Thomson Microelectronics
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 1.10
- bDeviceClass 0 (Defined at Interface level)
- bDeviceSubClass 0
- bDeviceProtocol 0
- bMaxPacketSize0 16
- idVendor 0x0483 SGS Thomson Microelectronics
- idProduct 0x0321
- bcdDevice 1.92
- iManufacturer 1 Generic
- iProduct 2 USB Mass Storage Device
- iSerial 3 7777777777777777
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 32
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0x80
- (Bus Powered)
- MaxPower 100mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 2
- bInterfaceClass 8 Mass Storage
- bInterfaceSubClass 6 SCSI
- bInterfaceProtocol 80 Bulk (Zip)
- iInterface 4 4in1
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x82 EP 2 IN
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0040 1x 64 bytes
- bInterval 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x02 EP 2 OUT
- bmAttributes 2
- Transfer Type Bulk
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0040 1x 64 bytes
- bInterval 0
- Device Status: 0x0000
- (Bus Powered)
-
- Bus 003 Device 001: ID 0000:0000
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 1.10
- bDeviceClass 9 Hub
- bDeviceSubClass 0 Unused
- bDeviceProtocol 0
- bMaxPacketSize0 64
- idVendor 0x0000
- idProduct 0x0000
- bcdDevice 2.06
- iManufacturer 3 Linux 2.6.15-26-686 uhci_hcd
- iProduct 2 UHCI Host Controller
- iSerial 1 0000:00:10.2
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 25
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 0mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0 Unused
- bInterfaceProtocol 0
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0002 1x 2 bytes
- bInterval 255
- Hub Descriptor:
- bLength 9
- bDescriptorType 41
- nNbrPorts 2
- wHubCharacteristic 0x000a
- No power switching (usb 1.0)
- Per-port overcurrent protection
- bPwrOn2PwrGood 1 * 2 milli seconds
- bHubContrCurrent 0 milli Ampere
- DeviceRemovable 0x78
- PortPwrCtrlMask 0x01
- Hub Port Status:
- Port 1: 0000.0103 power enable connect
- Port 2: 0000.0300 lowspeed power
- Device Status: 0x0003
- Self Powered
- Remote Wakeup Enabled
-
- Bus 002 Device 001: ID 0000:0000
- Device Descriptor:
- bLength 18
- bDescriptorType 1
- bcdUSB 1.10
- bDeviceClass 9 Hub
- bDeviceSubClass 0 Unused
- bDeviceProtocol 0
- bMaxPacketSize0 64
- idVendor 0x0000
- idProduct 0x0000
- bcdDevice 2.06
- iManufacturer 3 Linux 2.6.15-26-686 uhci_hcd
- iProduct 2 UHCI Host Controller
- iSerial 1 0000:00:10.1
- bNumConfigurations 1
- Configuration Descriptor:
- bLength 9
- bDescriptorType 2
- wTotalLength 25
- bNumInterfaces 1
- bConfigurationValue 1
- iConfiguration 0
- bmAttributes 0xe0
- Self Powered
- Remote Wakeup
- MaxPower 0mA
- Interface Descriptor:
- bLength 9
- bDescriptorType 4
- bInterfaceNumber 0
- bAlternateSetting 0
- bNumEndpoints 1
- bInterfaceClass 9 Hub
- bInterfaceSubClass 0 Unused
- bInterfaceProtocol 0
- iInterface 0
- Endpoint Descriptor:
- bLength 7
- bDescriptorType 5
- bEndpointAddress 0x81 EP 1 IN
- bmAttributes 3
- Transfer Type Interrupt
- Synch Type None
- Usage Type Data
- wMaxPacketSize 0x0002 1x 2 bytes
- bInterval 255
- Hub Descriptor:
- bLength 9
- bDescriptorType 41
- nNbrPorts 2
- wHubCharacteristic 0x000a
- No power switching (usb 1.0)
- Per-port overcurrent protection
- bPwrOn2PwrGood 1 * 2 milli seconds
- bHubContrCurrent 0 milli Ampere
- DeviceRemovable 0xf0
- PortPwrCtrlMask 0x01
- Hub Port Status:
- Port 1: 0000.0300 lowspeed power
- Port 2: 0000.0300 lowspeed power
- Device Status: 0x0003
- Self Powered
- Remote Wakeup Enabled
-
- lspci -vv
-
- 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
- Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
- Latency: 8
- Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
- Capabilities: [80] AGP version 3.5
- Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8
- Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
- Capabilities: [c0] #08 [0060]
- Capabilities: [68] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- Capabilities: [58] #08 [8001]
-
- 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] (prog-if 00 [Normal decode])
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 0
- Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
- I/O behind bridge: 00002000-00002fff
- Memory behind bridge: d0100000-d01fffff
- Prefetchable memory behind bridge: d8000000-dfffffff
- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
- Capabilities: [80] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:07.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus Controller (rev 02)
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 168, Cache Line Size: 0x08 (32 bytes)
- Interrupt: pin A routed to IRQ 169
- Region 0: Memory at 34000000 (32-bit, non-prefetchable) [size=4K]
- Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
- Memory window 0: 30000000-31fff000 (prefetchable)
- Memory window 1: 32000000-33fff000
- I/O window 0: 00001c00-00001cff
- I/O window 1: 00003000-000030ff
- BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
- 16-bit legacy interface ports at 0001
-
- 0000:00:07.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394 Controller (prog-if 10 [OHCI])
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64 (750ns min, 1000ns max), Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin B routed to IRQ 185
- Region 0: Memory at d0015000 (32-bit, non-prefetchable) [size=2K]
- Region 1: Memory at d0010000 (32-bit, non-prefetchable) [size=16K]
- Capabilities: [44] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME+
-
- 0000:00:09.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
- Subsystem: Intel Corporation: Unknown device 2721
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64 (750ns min, 6000ns max), Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin A routed to IRQ 193
- Region 0: Memory at d0014000 (32-bit, non-prefetchable) [size=4K]
- Capabilities: [dc] Power Management version 2
- Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
- Status: D0 PME-Enable- DSel=0 DScale=1 PME-
-
- 0000:00:0b.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64 (16000ns min), Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin A routed to IRQ 169
- Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=64K]
- Capabilities: [48] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
- Status: D0 PME-Enable- DSel=0 DScale=1 PME-
- Capabilities: [50] Vital Product Data
- Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
- Address: ffefbfddfe7fc7fc Data: fb7f
-
- 0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64, Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin A routed to IRQ 177
- Region 4: I/O ports at 1800 [size=32]
- Capabilities: [80] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME+
-
- 0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64, Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin B routed to IRQ 177
- Region 4: I/O ports at 1820 [size=32]
- Capabilities: [80] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64, Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin C routed to IRQ 177
- Region 4: I/O ports at 1840 [size=32]
- Capabilities: [80] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64, Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin D routed to IRQ 177
- Region 0: Memory at d0015800 (32-bit, non-prefetchable) [size=256]
- Capabilities: [80] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 0
- Capabilities: [c0] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 64
- Interrupt: pin A routed to IRQ 0
- Region 4: I/O ports at 1860 [size=16]
- Capabilities: [c0] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Interrupt: pin C routed to IRQ 201
- Region 0: I/O ports at 1000 [size=256]
- Capabilities: [c0] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Interrupt: pin C routed to IRQ 201
- Region 0: I/O ports at 1400 [size=256]
- Capabilities: [d0] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-
- 0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
- Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Capabilities: [80] #08 [2101]
-
- 0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
- Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
-
- 0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
- Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
-
- 0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
- Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
-
- 0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] (prog-if 00 [VGA])
- Subsystem: Acer Incorporated [ALI]: Unknown device 0057
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- Latency: 255 (2000ns min), Cache Line Size: 0x10 (64 bytes)
- Interrupt: pin A routed to IRQ 209
- Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
- Region 1: I/O ports at 2000 [size=256]
- Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
- Expansion ROM at d0120000 [disabled] [size=128K]
- Capabilities: [58] AGP version 3.0
- Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
- Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
- Capabilities: [50] Power Management version 2
- Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME-
** Attachment added: "lsusb"
http://librarian.launchpad.net/4292735/lsusb.txt
--
SGS Thomson 5in1 card reader not mounting sd
https://launchpad.net/bugs/60963
More information about the kernel-bugs
mailing list