[Bug 15161] Bad and weak sound on G5 powermac
bugzilla-daemon at bugzilla.ubuntu.com
bugzilla-daemon at bugzilla.ubuntu.com
Tue Sep 13 21:34:38 UTC 2005
Please do not reply to this email. You can add comments at
http://bugzilla.ubuntu.com/show_bug.cgi?id=15161
Ubuntu | linux
------- Additional Comments From bertranddekoninck at wanadoo.fr 2005-09-13 22:34 UTC -------
(In reply to comment #0)
> The sound is very week on Ubuntu Breezy-preview. I've tried to set the levels with the gnome mixer, but, with an
> upper PCM level, the sound is also weak and then distorted.
>
> Bertrand Dekoninck
(In reply to comment #1)
> Can you send output for lspci and dmesg please?
Here they are :
lspci :
0000:f0:0b.0 Host bridge: Apple Computer Inc.: Unknown device 0059
0000:f0:10.0 VGA compatible controller: ATI Technologies Inc RV350 AP [Radeon 9600]
0001:00:01.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge
0001:00:02.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge
0001:00:03.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge
0001:00:04.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge
0001:00:05.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge
0001:01:07.0 ff00: Apple Computer Inc. K2 KeyLargo Mac/IO (rev 60)
0001:01:08.0 USB Controller: Apple Computer Inc. K2 KeyLargo USB
0001:01:09.0 USB Controller: Apple Computer Inc. K2 KeyLargo USB
0001:02:0d.0 ff00: Apple Computer Inc. K2 ATA/100
0001:02:0e.0 FireWire (IEEE 1394): Apple Computer Inc. K2 FireWire
0001:03:0f.0 Ethernet controller: Apple Computer Inc. K2 GMAC (Sun GEM)
0001:04:0c.0 IDE interface: ServerWorks: Unknown device 0240
0001:05:0b.0 USB Controller: NEC Corporation USB (rev 43)
0001:05:0b.1 USB Controller: NEC Corporation USB (rev 43)
0001:05:0b.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
dmesg :
[ 0.000000] Found initrd at 0xc000000001a00000:0xc000000001fea000
[ 0.000000] trying to initialize btext ...
[ 0.000000] U3-DART: table not allocated, using direct DMA
[ 0.000000] Starting Linux PPC64 2.6.12-8-powerpc64-smp
[ 0.000000] -----------------------------------------------------
[ 0.000000] ppc64_pft_size = 0x18
[ 0.000000] ppc64_debug_switch = 0x0
[ 0.000000] ppc64_interrupt_controller = 0x1
[ 0.000000] systemcfg = 0xc000000000320000
[ 0.000000] systemcfg->platform = 0x400
[ 0.000000] systemcfg->processorCount = 0x2
[ 0.000000] systemcfg->physicalMemorySize = 0x40000000
[ 0.000000] ppc64_caches.dcache_line_size = 0x80
[ 0.000000] ppc64_caches.icache_line_size = 0x80
[ 0.000000] htab_address = 0xc00000003e000000
[ 0.000000] htab_hash_mask = 0x1ffff
[ 0.000000] -----------------------------------------------------
[ 0.000000] [boot]0100 MM Init
[ 0.000000] [boot]0100 MM Init Done
[ 0.000000] Linux version 2.6.12-8-powerpc64-smp (buildd at adare) (gcc version 3.4.5 20050809 (prerelease) (Debian 3.4.4-6ubuntu6)) #1 SMP Tue
Aug 30 23:43:33 BST 2005
[ 0.000000] [boot]0012 Setup Arch
[ 0.000000] Top of RAM: 0x40000000, Total RAM: 0x40000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Syscall map setup, 244 32 bits and 220 64 bits syscalls
[ 0.000000] Found U3 memory controller & host bridge, revision: 55
[ 0.000000] Mapped at 0xe000000080140000
[ 0.000000] Found a K2 mac-io controller, rev: 96, mapped at 0xe000000080181000
[ 0.000000] PowerMac motherboard: PowerMac G5
[ 0.000000] nvram: Checking bank 0...
[ 0.000000] nvram: gen0=390, gen1=391
[ 0.000000] nvram: Active bank is: 1
[ 0.000000] Adding PCI host bridge /pci at 0,f0000000
[ 0.000000] Found U3-AGP PCI host bridge. Firmware bus number: 240->255
[ 0.000000] Adding PCI host bridge /ht at 0,f2000000
[ 0.000000] Can't get bus-range for /ht at 0,f2000000, assume bus 0
[ 0.000000] U3/HT: hole, 0 end at 8fffffff, 1 start at a0000000
[ 0.000000] Found U3-HT PCI host bridge. Firmware bus number: 0->239
[ 0.000000] Can't get bus-range for /ht at 0,f2000000
[ 0.000000] PCI Host 0, io start: fffffffffd800000; io end: fffffffffdffffff
[ 0.000000] PCI Host 1, io start: 0; io end: 3fffff
[ 0.000000] Using native/NAP idle loop
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] DMA zone: 262144 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages, LIFO batch:1
[ 0.000000] HighMem zone: 0 pages, LIFO batch:1
[ 0.000000] [boot]0015 Setup Done
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: root=/dev/sda5 ro quiet splash
[ 0.000000] PowerMac using OpenPIC irq controller at 0x80040000
[ 0.000000] mpic: Setting up MPIC " K2-MPIC " version 1.2 at 80040000, max 4 CPUs
[ 0.000000] mpic: ISU size: 120, shift: 7, mask: 7f
[ 0.000000] mpic: Initializing for 120 sources
[ 0.000000] Slave OpenPIC at 0xf8040000 hooked on IRQ 56
[ 0.000000] mpic: Setting up MPIC " U3-MPIC " version 1.2 at f8040000, max 4 CPUs
[ 0.000000] mpic: ISU size: 124, shift: 7, mask: 7f
[ 0.000000] mpic: Initializing for 124 sources
[ 0.000000] PID hash table entries: 4096 (order: 12, 131072 bytes)
[ 0.000000] time_init: decrementer frequency = 33.333333 MHz
[ 18.363399] Console: colour dummy device 80x25
[ 18.364938] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 18.367029] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 18.367904] freeing bootmem node 0
[ 18.383166] Memory: 1001596k/1048576k available (2632k kernel code, 46252k reserved, 1300k data, 275k bss, 220k init)
[ 18.383312] Calibrating delay loop... 66.56 BogoMIPS (lpj=33280)
[ 18.402407] Security Framework v1.0.0 initialized
[ 18.402413] SELinux: Disabled at boot.
[ 18.402440] Mount-cache hash table entries: 256
[ 18.404770] checking if image is initramfs... it is
[ 18.995180] Freeing initrd memory: 6056k freed
[ 18.995798] PowerMac SMP probe found 2 cpus
[ 18.995811] Timebase clock is Pulsar chip
[ 18.995814] requesting IPIs ...
[ 18.995860] IPIs requested...
[ 19.076196] Processor 1 found.
[ 19.080223] Brought up 2 CPUs
[ 19.080459] CPU0 attaching sched-domain:
[ 19.080462] domain 0: span 00000001
[ 19.080466] groups: 00000001
[ 19.080472] domain 1: span 00000003
[ 19.080477] groups: 00000001 00000002
[ 19.080484] domain 2: span 00000003
[ 19.080490] groups: 00000003
[ 19.080497] CPU1 attaching sched-domain:
[ 19.080499] domain 0: span 00000002
[ 19.080503] groups: 00000002
[ 19.080509] domain 1: span 00000003
[ 19.080513] groups: 00000002 00000001
[ 19.080521] domain 2: span 00000003
[ 19.080526] groups: 00000003
[ 19.081497] NET: Registered protocol family 16
[ 19.179728] PCI: Probing PCI hardware
[ 19.182296] PCI: Probing PCI hardware done
[ 19.183233] TC classifier action (bugs to netdev at vger.kernel.org cc hadi at cyberus.ca)
[ 19.183848] i/pSeries Real Time Clock Driver v1.1
[ 19.184098] nvram_init: Could not find nvram partition for nvram buffered error logging.
[ 19.185273] audit: initializing netlink socket (disabled)
[ 19.185288] audit(16559223310752.188:0): initialized
[ 19.185604] VFS: Disk quotas dquot_6.5.1
[ 19.185634] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 19.185679] devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
[ 19.185691] devfs: boot_options: 0x0
[ 19.185742] Initializing Cryptographic API
[ 19.186135] PCI: Enabling device: (0000:f0:10.0), cmd 7
[ 19.384649] radeonfb: Found Open Firmware ROM Image
[ 19.384655] radeonfb: Retreived PLL infos from Open Firmware
[ 19.384660] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=200.00 Mhz, System=325.00 MHz
[ 19.384664] radeonfb: PLL min 12000 max 35000
[ 19.955701] radeonfb: Monitor 1 type CRT found
[ 19.955704] radeonfb: EDID probed
[ 19.955707] radeonfb: Monitor 2 type CRT found
[ 19.962227] Trying to im_free nonexistent area (e000000080000000)
[ 20.014519] Console: switching to colour frame buffer device 160x64
[ 20.014714] radeonfb (0000:f0:10.0): ATI Radeon AP
[ 20.058797] vio_register_driver: driver hvc_console registering
[ 20.058859] HVSI: registered 0 devices
[ 20.058867] io scheduler noop registered
[ 20.058896] io scheduler anticipatory registered
[ 20.058908] io scheduler deadline registered
[ 20.058937] io scheduler cfq registered
[ 20.059960] RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
[ 20.060132] MacIO PCI driver attached to K2 chipset
[ 20.060877] PowerMac G5 Thermal control driver 1.2b2
[ 20.061040] Detected fan controls:
[ 20.061043] 0: PWM fan, id 1, location: BACKSIDE,SYS CTRLR FAN
[ 20.061046] 1: RPM fan, id 2, location: DRIVE BAY
[ 20.061049] 2: PWM fan, id 2, location: SLOT,PCI FAN
[ 20.061052] 3: RPM fan, id 3, location: CPU A INTAKE
[ 20.061055] 4: RPM fan, id 4, location: CPU A EXHAUST
[ 20.061058] 5: RPM fan, id 5, location: CPU B INTAKE
[ 20.061061] 6: RPM fan, id 6, location: CPU B EXHAUST
[ 20.061124] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 20.061133] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 20.061254] PCI: Enabling device: (0001:02:0d.0), cmd 16
[ 21.073205] ide0: Found Apple K2 ATA-6 controller, bus ID 3, irq 39
[ 21.073219] Probing IDE interface ide0...
[ 21.439527] hda: SONY DVD RW DW-Q28A, ATAPI CD/DVD-ROM drive
[ 22.051234] ide0 at 0xe000000083f7c000-0xe000000083f7c007,0xe000000083f7c160 on irq 39
[ 22.051524] mice: PS/2 mouse device common for all mice
[ 22.051584] /u3 at 0,f8000000/i2c at f8001000: Missing interrupt or address !
[ 22.051952] Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
[ 22.052033] NET: Registered protocol family 2
[ 22.063859] IP: routing cache hash table of 4096 buckets, 64Kbytes
[ 22.064155] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 22.069504] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 22.070852] TCP: Hash tables configured (established 262144 bind 65536)
[ 22.071163] Freeing unused kernel memory: 220k freed
[ 22.117773] Capability LSM initialized
[ 22.126858] NET: Registered protocol family 1
[ 22.321326] usbcore: registered new driver usbfs
[ 22.321415] usbcore: registered new driver hub
[ 22.322536] ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 22.322630] PCI: Enabling device: (0001:01:08.0), cmd 2
[ 22.322654] ohci_hcd 0001:01:08.0: Apple Computer Inc. K2 KeyLargo USB
[ 22.322782] ohci_hcd 0001:01:08.0: new USB bus registered, assigned bus number 1
[ 22.322794] ohci_hcd 0001:01:08.0: irq 27, io mem 0x80081000
[ 22.354241] hub 1-0:1.0: USB hub found
[ 22.354257] hub 1-0:1.0: 2 ports detected
[ 22.375241] PCI: Enabling device: (0001:01:09.0), cmd 2
[ 22.375258] ohci_hcd 0001:01:09.0: Apple Computer Inc. K2 KeyLargo USB (#2)
[ 22.375349] ohci_hcd 0001:01:09.0: new USB bus registered, assigned bus number 2
[ 22.375361] ohci_hcd 0001:01:09.0: irq 28, io mem 0x80080000
[ 22.405693] hub 2-0:1.0: USB hub found
[ 22.405712] hub 2-0:1.0: 2 ports detected
[ 22.426730] PCI: Enabling device: (0001:05:0b.0), cmd 2
[ 22.426743] ohci_hcd 0001:05:0b.0: NEC Corporation USB
[ 22.426824] ohci_hcd 0001:05:0b.0: new USB bus registered, assigned bus number 3
[ 22.426836] ohci_hcd 0001:05:0b.0: irq 63, io mem 0x80702000
[ 22.458179] hub 3-0:1.0: USB hub found
[ 22.458193] hub 3-0:1.0: 3 ports detected
[ 22.479231] PCI: Enabling device: (0001:05:0b.1), cmd 2
[ 22.479244] ohci_hcd 0001:05:0b.1: NEC Corporation USB (#2)
[ 22.479328] ohci_hcd 0001:05:0b.1: new USB bus registered, assigned bus number 4
[ 22.479336] ohci_hcd 0001:05:0b.1: irq 63, io mem 0x80701000
[ 22.509680] hub 4-0:1.0: USB hub found
[ 22.509695] hub 4-0:1.0: 2 ports detected
[ 22.619608] sungem.c:v0.98 8/24/03 David S. Miller (davem at redhat.com)
[ 22.663014] PHY ID: 2062e0, addr: 1
[ 22.664416] eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:14:51:03:bd:56
[ 22.664427] eth0: Found BCM5421-K2 PHY
[ 22.692132] SCSI subsystem initialized
[ 22.694066] libata version 1.11 loaded.
[ 22.695585] sata_svw version 1.05
[ 22.695711] ata1: SATA max UDMA/133 cmd 0xE000000084183000 ctl 0xE000000084183020 bmdma 0xE000000084183030 irq 0
[ 22.695777] ata2: SATA max UDMA/133 cmd 0xE000000084183100 ctl 0xE000000084183120 bmdma 0xE000000084183130 irq 0
[ 22.695821] ata3: SATA max UDMA/133 cmd 0xE000000084183200 ctl 0xE000000084183220 bmdma 0xE000000084183230 irq 0
[ 22.695873] ata4: SATA max UDMA/133 cmd 0xE000000084183300 ctl 0xE000000084183320 bmdma 0xE000000084183330 irq 0
[ 22.899975] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:007f
[ 22.899980] ata1: dev 0 ATA, max UDMA/133, 320173056 sectors: lba48
[ 22.900943] ata1: dev 0 configured for UDMA/133
[ 22.900947] scsi0 : sata_svw
[ 23.101706] ata2: no device found (phy stat 00000004)
[ 23.101710] scsi1 : sata_svw
[ 23.279707] usb 4-2: new full speed USB device using ohci_hcd and address 2
[ 23.303206] ata3: no device found (phy stat 00000004)
[ 23.303210] scsi2 : sata_svw
[ 23.387743] hub 4-2:1.0: USB hub found
[ 23.390677] hub 4-2:1.0: 3 ports detected
[ 23.503707] ata4: no device found (phy stat 00000004)
[ 23.503710] scsi3 : sata_svw
[ 23.503947] Vendor: ATA Model: Maxtor 6B160M0 Rev: BANC
[ 23.503969] Type: Direct-Access ANSI SCSI revision: 05
[ 23.575943] PCI: Enabling device: (0001:05:0b.2), cmd 6
[ 23.575961] ehci_hcd 0001:05:0b.2: NEC Corporation USB 2.0
[ 23.592662] usb 4-2.1: new low speed USB device using ohci_hcd and address 3
[ 23.596819] ehci_hcd 0001:05:0b.2: new USB bus registered, assigned bus number 5
[ 23.596830] ehci_hcd 0001:05:0b.2: irq 63, io mem 0x80700000
[ 23.596875] ehci_hcd 0001:05:0b.2: park 0
[ 23.596884] ehci_hcd 0001:05:0b.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[ 23.597076] hub 5-0:1.0: USB hub found
[ 23.597090] hub 5-0:1.0: 5 ports detected
[ 23.620672] hub 4-2:1.0: hub_port_status failed (err = -110)
[ 23.623677] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.626662] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.629666] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.632664] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.632838] hub 4-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 23.635658] hub 4-2:1.0: cannot disable port 1 (err = -110)
[ 23.638666] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.641665] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.644659] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.647658] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.650662] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.650838] hub 4-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 23.653660] hub 4-2:1.0: cannot disable port 1 (err = -110)
[ 23.656660] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.659664] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.662662] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.665657] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.668656] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.668829] hub 4-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 23.671660] hub 4-2:1.0: cannot disable port 1 (err = -110)
[ 23.674658] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.677657] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.680660] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.683658] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.686658] hub 4-2:1.0: cannot reset port 1 (err = -110)
[ 23.686830] hub 4-2:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 23.689662] hub 4-2:1.0: cannot disable port 1 (err = -110)
[ 23.692660] hub 4-2:1.0: cannot disable port 1 (err = -110)
[ 23.707656] hub 4-2:1.0: hub_port_status failed (err = -110)
[ 23.722659] hub 4-2:1.0: hub_port_status failed (err = -110)
[ 23.878394] usb 4-2: USB disconnect, address 2
[ 24.055707] usb 4-2: new full speed USB device using ohci_hcd and address 7
[ 24.163716] hub 4-2:1.0: USB hub found
[ 24.166626] hub 4-2:1.0: 3 ports detected
[ 24.368612] usb 4-2.1: new low speed USB device using ohci_hcd and address 8
[ 24.571604] usb 4-2.2: new full speed USB device using ohci_hcd and address 9
[ 24.774593] usb 4-2.3: new full speed USB device using ohci_hcd and address 10
[ 25.063848] eth0: Link is up at 100 Mbps, full-duplex.
[ 25.730606] usbcore: registered new driver hiddev
[ 25.739674] input: USB HID v1.10 Mouse [Microsoft Microsoft USB Mouse] on usb-0001:05:0b.1-2.1
[ 25.749640] input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:05:0b.1-2.3
[ 25.760596] input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:05:0b.1-2.3
[ 25.760608] usbcore: registered new driver usbhid
[ 25.760613] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[ 25.876559] ide_generic: doesn't contain .toc or .stubs.
[ 25.888515] hda: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[ 25.888526] Uniform CD-ROM driver Revision: 3.20
[ 25.898212] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
[ 25.898254] SCSI device sda: drive cache: write back
[ 25.898416] SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB)
[ 25.898454] SCSI device sda: drive cache: write back
[ 25.898460] /dev/scsi/host0/bus0/target0/lun0: [mac] p1 p2 p3 p4 p5 p6 p7 p8
[ 25.918978] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 27.167113] kjournald starting. Commit interval 5 seconds
[ 27.167158] EXT3-fs: mounted filesystem with ordered data mode.
[ 28.002430] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 32.313509] Adding 2217976k swap on /dev/sda7. Priority:-1 extents:1
[ 32.456721] EXT3 FS on sda5, internal journal
[ 34.343402] ieee1394: Initialized config rom entry `ip1394'
[ 34.352125] sbp2: Unknown symbol bus_to_virt
[ 38.143227] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
[ 38.730867] cdrom: open failed.
[ 38.732715] ioctl32(evms_activate:4729): Unknown cmd fd(7) cmd(00000330){00} arg(ff9025d8) on /dev/evms/.nodes/sda
[ 39.235619] kjournald starting. Commit interval 5 seconds
[ 39.235783] EXT3 FS on sda6, internal journal
[ 39.235791] EXT3-fs: mounted filesystem with ordered data mode.
[ 40.230633] Linux agpgart interface v0.101 (c) Dave Jones
[ 40.232007] uninorth_agp: Unknown symbol flush_dcache_range
[ 40.454996] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 40.461481] shpchp: shpc_init : shpc_cap_offset == 0
[ 40.461493] shpchp: shpc_init : shpc_cap_offset == 0
[ 40.461502] shpchp: shpc_init : shpc_cap_offset == 0
[ 40.461512] shpchp: shpc_init : shpc_cap_offset == 0
[ 40.461521] shpchp: shpc_init : shpc_cap_offset == 0
[ 40.461528] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 41.131154] ohci1394: $Rev: 1250 $ Ben Collins <bcollins at debian.org>
[ 41.131173] PCI: Enabling device: (0001:02:0e.0), cmd 2
[ 41.134140] ohci1394: fw-host0: Unexpected PCI resource length of 1000!
[ 41.185829] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[80100000-801007ff] Max Packet=[4096]
[ 42.457168] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001451fffe03bd56]
[ 43.669754] ts: Compaq touchscreen protocol output
[ 44.451665] eth0: Link is up at 100 Mbps, full-duplex.
[ 44.451672] eth0: Pause is disabled
[ 45.752381] NET: Registered protocol family 10
[ 45.752631] Disabled Privacy Extensions on device c0000000003f10d0(lo)
[ 45.808483] IPv6 over IPv4 tunneling driver
[ 51.023444] lp: driver loaded but no devices found
[ 53.314397] ioctl32(pbbuttonsd:6627): Unknown cmd fd(3) cmd(401f4520){00} arg(ff939980) on /dev/input/event0
[ 53.314970] ioctl32(pbbuttonsd:6627): Unknown cmd fd(3) cmd(401f4520){00} arg(ff939980) on /dev/input/event1
[ 53.315227] ioctl32(pbbuttonsd:6627): Unknown cmd fd(3) cmd(401f4520){00} arg(ff939980) on /dev/input/event2
[ 53.315323] ioctl32(pbbuttonsd:6627): Unknown cmd fd(3) cmd(401f4520){00} arg(ff939980) on /dev/input/event3
[ 53.984757] Bluetooth: Core ver 2.7
[ 53.984772] NET: Registered protocol family 31
[ 53.984775] Bluetooth: HCI device and connection manager initialized
[ 53.984800] Bluetooth: HCI socket layer initialized
[ 54.001568] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/005/001
[ 54.002197] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/004/010
[ 54.002536] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/004/009
[ 54.002907] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/004/008
[ 54.003218] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/004/007
[ 54.003520] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/004/001
[ 54.003897] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/003/001
[ 54.004269] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/002/001
[ 54.004648] ioctl32(hid2hci:6704): Unknown cmd fd(3) cmd(c00c5512){00} arg(fff8b5d8) on /proc/bus/usb/001/001
[ 54.009617] Bluetooth: L2CAP ver 2.7
[ 54.009623] Bluetooth: L2CAP socket layer initialized
[ 54.049776] Bluetooth: RFCOMM ver 1.5
[ 54.049791] Bluetooth: RFCOMM socket layer initialized
[ 54.049811] Bluetooth: RFCOMM TTY layer initialized
[ 56.617205] eth0: no IPv6 routers present
--
Configure bugmail: http://bugzilla.ubuntu.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the QA contact for the bug, or are watching the QA contact.
More information about the kernel-bugs
mailing list