[Bug 18470] Unable to load the system description tables
bugzilla-daemon at bugzilla.ubuntu.com
bugzilla-daemon at bugzilla.ubuntu.com
Thu Nov 17 21:47:15 UTC 2005
Please do not reply to this email. You can add comments at
http://bugzilla.ubuntu.com/show_bug.cgi?id=18470
Ubuntu | linux
------- Additional Comments From leezer3 at gmail.com 2005-11-17 21:47 UTC -------
Hiya,
Dmesg output from custom compiled kernel 2.6.13.4 (Default options, other than
disabling PCMCIA & a couple of other drivers):
DEP tag
[ 21.414938] PnPBIOS: Missing SMALL_TAG_ENDDEP tag
[ 21.415071] PnPBIOS: Missing SMALL_TAG_ENDDEP tag
[ 21.415188] PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
[ 21.415216] PCI: Probing PCI hardware
[ 21.415218] PCI: Probing PCI hardware (bus 00)
[ 21.415828] PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
[ 21.416165] Boot video device is 0000:01:00.0
[ 21.416478] PCI: Transparent bridge - 0000:00:14.4
[ 21.416834] PCI: Using IRQ router default [1002/4377] at 0000:00:14.3
[ 21.416842] PCI->APIC IRQ transform: 0000:00:11.0[A] -> IRQ 23
[ 21.416846] PCI->APIC IRQ transform: 0000:00:12.0[A] -> IRQ 22
[ 21.416850] PCI->APIC IRQ transform: 0000:00:13.0[A] -> IRQ 19
[ 21.416853] PCI->APIC IRQ transform: 0000:00:13.1[A] -> IRQ 19
[ 21.416857] PCI->APIC IRQ transform: 0000:00:13.2[A] -> IRQ 19
[ 21.416862] PCI->APIC IRQ transform: 0000:00:14.1[A] -> IRQ 16
[ 21.416866] PCI->APIC IRQ transform: 0000:00:14.2[A] -> IRQ 16
[ 21.416873] PCI->APIC IRQ transform: 0000:01:00.0[A] -> IRQ 18
[ 21.416877] PCI->APIC IRQ transform: 0000:02:03.0[A] -> IRQ 20
[ 21.416882] PCI->APIC IRQ transform: 0000:02:04.0[A] -> IRQ 21
[ 21.426895] pnp: 00:0b: ioport range 0x600-0x607 has been reserved
[ 21.426899] pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved
[ 21.426901] pnp: 00:0c: ioport range 0xcf8-0xcff could not be reserved
[ 21.426903] pnp: 00:0c: ioport range 0x800-0x8fe has been reserved
[ 21.426906] pnp: 00:0c: ioport range 0xc000-0xc003 has been reserved
[ 21.426908] pnp: 00:0c: ioport range 0xc400-0xc403 has been reserved
[ 21.426911] pnp: 00:0c: ioport range 0xc800-0xc803 has been reserved
[ 21.426913] pnp: 00:0c: ioport range 0xcc00-0xcc03 has been reserved
[ 21.426915] pnp: 00:0c: ioport range 0x290-0x297 has been reserved
[ 21.427035] PCI: Bridge: 0000:00:02.0
[ 21.427037] IO window: disabled.
[ 21.427040] MEM window: fc000000-feafffff
[ 21.427043] PREFETCH window: d0000000-dfffffff
[ 21.427046] PCI: Bridge: 0000:00:14.4
[ 21.427049] IO window: e000-efff
[ 21.427056] MEM window: feb00000-febfffff
[ 21.427060] PREFETCH window: 40000000-400fffff
[ 21.427069] PCI: 0000:00:02.0 has unsupported PM cap regs version (3)
[ 21.427074] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 21.427272] audit: initializing netlink socket (disabled)
[ 21.427280] audit(1132263950.860:1): initialized
[ 21.427314] highmem bounce pool size: 64 pages
[ 21.427370] VFS: Disk quotas dquot_6.5.1
[ 21.427387] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 21.427432] Initializing Cryptographic API
[ 21.427501] PCI: 0000:00:02.0 has unsupported PM cap regs version (3)
[ 21.427506] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 21.427509] pcie_portdrv_probe->Dev[5a34:1002] has invalid IRQ. Check vendor BIOS
[ 21.427531] assign_interrupt_mode Found MSI capability
[ 21.427533] Allocate Port Service[pcie00]
[ 21.427583] isapnp: Scanning for PnP cards...
[ 21.782234] isapnp: No Plug & Play device found
[ 21.789494] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 21.791001] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 21.791167] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 21.791170] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 21.791364] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 21.791683] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 21.791749] io scheduler noop registered
[ 21.791762] io scheduler anticipatory registered
[ 21.791769] io scheduler deadline registered
[ 21.791784] io scheduler cfq registered
[ 21.791981] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 21.792047] NET: Registered protocol family 2
[ 21.815247] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 21.820496] IP route cache hash table entries: 65536 (order: 6, 262144
bytes)[ 21.820848] TCP established hash table entries: 262144 (order: 9,
2097152 bytes)
[ 21.823146] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 21.823420] TCP: Hash tables configured (established 262144 bind 65536)
[ 21.823422] TCP reno registered
[ 21.823489] TCP bic registered
[ 21.823491] NET: Registered protocol family 8
[ 21.823493] NET: Registered protocol family 20
[ 21.823515] Using IPI Shortcut mode
[ 21.823732] Freeing unused kernel memory: 172k freed
[ 21.835678] vga16fb: initializing
[ 21.835681] vga16fb: mapped to 0xc00a0000
[ 22.065605] Console: switching to colour frame buffer device 80x30
[ 22.065609] fb0: VGA16 VGA frame buffer device
[ 22.753662] NET: Registered protocol family 1
[ 22.761808] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 22.761813] ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
[ 22.764118] SCSI subsystem initialized
[ 22.764674] libata version 1.12 loaded.
[ 22.765213] sata_sil version 0.9
[ 22.765278] ata1: SATA max UDMA/100 cmd 0xF8856C80 ctl 0xF8856C8A bmdma
0xF8856C00 irq 23
[ 22.765296] ata2: SATA max UDMA/100 cmd 0xF8856CC0 ctl 0xF8856CCA bmdma
0xF8856C08 irq 23
[ 22.951003] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01
87:4663 88:407f
[ 22.951006] ata1: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
[ 22.951937] ata1: dev 0 configured for UDMA/100
[ 22.951943] scsi0 : sata_sil
[ 23.053664] ata2: no device found (phy stat 00000000)
[ 23.053666] scsi1 : sata_sil
[ 23.053736] Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
[ 23.053741] Type: Direct-Access ANSI SCSI revision: 05
[ 23.054388] ata3: SATA max UDMA/100 cmd 0xF8866880 ctl 0xF886688A bmdma
0xF8866800 irq 22
[ 23.054405] ata4: SATA max UDMA/100 cmd 0xF88668C0 ctl 0xF88668CA bmdma
0xF8866808 irq 22
[ 23.156738] ata3: no device found (phy stat 00000000)
[ 23.156740] scsi2 : sata_sil
[ 23.259834] ata4: no device found (phy stat 00000000)
[ 23.259836] scsi3 : sata_sil
[ 23.275220] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[ 23.275245] ATIIXP: chipset revision 128
[ 23.275247] ATIIXP: not 100% native mode: will probe irqs later
[ 23.275257] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
[ 23.275271] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:pio, hdd:pio
[ 23.275279] Probing IDE interface ide0...
[ 23.644883] hda: AOPEN DUW1608/ARR, ATAPI CD/DVD-ROM drive
[ 24.033470] hdb: SONY DVD-ROM DDU1615, ATAPI CD/DVD-ROM drive
[ 24.060856] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 24.060895] Probing IDE interface ide1...
[ 24.351702] Probing IDE interface ide1...
[ 24.639741] hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[ 24.639748] Uniform CD-ROM driver Revision: 3.20
[ 24.643747] hdb: ATAPI 40X DVD-ROM drive, 254kB Cache
[ 24.651789] SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
[ 24.651798] SCSI device sda: drive cache: write back
[ 24.651839] SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
[ 24.651844] SCSI device sda: drive cache: write back
[ 24.651846] sda: sda1 sda2 sda3 < sda5 >
[ 24.686533] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 24.953173] Attempting manual resume
[ 24.953331] swsusp: Suspend partition has wrong signature?
[ 24.983931] usbcore: registered new driver usbfs
[ 24.983952] usbcore: registered new driver hub
[ 24.984400] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI)
Driver (PCI)
[ 24.984450] ohci_hcd 0000:00:13.0: PCI device 1002:4374 (ATI Technologies Inc)
[ 25.000714] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 25.000723] ohci_hcd 0000:00:13.0: irq 19, io mem 0xfbffa000
[ 25.032355] hub 1-0:1.0: USB hub found
[ 25.032368] hub 1-0:1.0: 4 ports detected
[ 25.036279] ohci_hcd 0000:00:13.1: PCI device 1002:4375 (ATI Technologies Inc)
[ 25.052139] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[ 25.052143] ohci_hcd 0000:00:13.1: irq 19, io mem 0xfbff9000
[ 25.083879] hub 2-0:1.0: USB hub found
[ 25.083889] hub 2-0:1.0: 4 ports detected
[ 25.100002] ehci_hcd 0000:00:13.2: PCI device 1002:4373 (ATI Technologies Inc)
[ 25.100059] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 25.100066] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfbff8000
[ 25.100103] ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10
Dec 2004
[ 25.100178] hub 3-0:1.0: USB hub found
[ 25.100186] hub 3-0:1.0: 8 ports detected
[ 25.174263] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[ 25.174293] 8139cp: pci dev 0000:02:03.0 (id 10ec:8139 rev 10) is not an
8139C+ compatible chip
[ 25.174296] 8139cp: Try the "8139too" driver instead.
[ 25.175461] 8139too Fast Ethernet driver 0.9.27
[ 25.176503] eth0: RealTek RTL8139 at 0xe800, 00:13:d3:97:e5:5a, IRQ 20
[ 25.176506] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 25.405021] usb 1-2: new low speed USB device using ohci_hcd and address 2
[ 26.186315] usbcore: registered new driver hiddev
[ 26.196077] input: USB HID v1.10 Joystick [Mega World USB Game Controllers]
on usb-0000:00:13.0-2
[ 26.196084] usbcore: registered new driver usbhid
[ 26.196086] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[ 26.897017] Attempting manual resume
[ 26.897152] swsusp: Suspend partition has wrong signature?
[ 26.917775] kjournald starting. Commit interval 5 seconds
[ 26.917786] EXT3-fs: mounted filesystem with ordered data mode.
[ 27.712381] md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 27.712385] md: bitmap version 3.38
[ 30.466485] Adding 1373516k swap on /dev/sda5. Priority:-1 extents:1
[ 30.754178] EXT3 FS on sda2, internal journal
[ 32.570658] parport: PnPBIOS parport detected.
[ 32.570726] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 32.619680] lp0: using parport0 (interrupt-driven).
[ 32.641789] mice: PS/2 mouse device common for all mice
[ 32.720295] ieee1394: Initialized config rom entry `ip1394'
[ 32.737460] sbp2: $Rev: 1306 $ Ben Collins <bcollins at debian.org>
[ 32.893712] input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
[ 33.192874] ts: Compaq touchscreen protocol output
[ 35.690302] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel at redhat.com
[ 36.447501] cdrom: open failed.
[ 36.543267] device-mapper: dm-linear: Device lookup failed
[ 36.543272] device-mapper: error adding target to table
[ 36.549701] device-mapper: dm-linear: Device lookup failed
[ 36.549707] device-mapper: error adding target to table
[ 36.556237] device-mapper: dm-linear: Device lookup failed
[ 36.556242] device-mapper: error adding target to table
[ 36.562722] device-mapper: dm-linear: Device lookup failed
[ 36.562727] device-mapper: error adding target to table
[ 36.569069] device-mapper: dm-linear: Device lookup failed
[ 36.569073] device-mapper: error adding target to table
[ 36.570312] device-mapper: dm-linear: Device lookup failed
[ 36.570316] device-mapper: error adding target to table
[ 36.583540] device-mapper: dm-linear: Device lookup failed
[ 36.583545] device-mapper: error adding target to table
[ 36.584912] device-mapper: dm-linear: Device lookup failed
[ 36.584916] device-mapper: error adding target to table
[ 36.586603] device-mapper: dm-linear: Device lookup failed
[ 36.586606] device-mapper: error adding target to table
[ 36.587910] device-mapper: dm-linear: Device lookup failed
[ 36.587914] device-mapper: error adding target to table
[ 36.589186] device-mapper: dm-linear: Device lookup failed
[ 36.589190] device-mapper: error adding target to table
[ 36.590458] device-mapper: dm-linear: Device lookup failed
[ 36.590462] device-mapper: error adding target to table
[ 37.025759] NTFS driver 2.1.23 [Flags: R/O MODULE].
[ 37.086695] NTFS volume version 3.1.
[ 38.727727] Linux agpgart interface v0.101 (c) Dave Jones
[ 38.848856] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 38.927805] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 39.652146] hda_codec: Unknown model for ALC880, trying auto-probe from BIOS...
[ 40.002599] hda_codec: num_steps = 0 for NID=0x8
[ 40.235036] hda_codec: num_steps = 0 for NID=0x9
[ 40.238331] hda_codec: num_steps = 0 for NID=0x9
[ 40.242669] hda_codec: num_steps = 0 for NID=0x9
[ 40.247525] hda_codec: num_steps = 0 for NID=0x9
[ 40.252961] hda_codec: num_steps = 0 for NID=0x9
[ 40.256269] hda_codec: num_steps = 0 for NID=0x9
[ 40.260634] hda_codec: num_steps = 0 for NID=0x9
[ 40.265860] hda_codec: num_steps = 0 for NID=0x9
[ 40.270145] hda_codec: num_steps = 0 for NID=0x9
[ 40.274444] hda_codec: num_steps = 0 for NID=0x9
[ 40.278770] hda_codec: num_steps = 0 for NID=0x9
[ 40.283166] hda_codec: num_steps = 0 for NID=0x9
[ 40.287396] hda_codec: num_steps = 0 for NID=0x9
[ 40.291729] hda_codec: num_steps = 0 for NID=0x9
[ 40.296108] hda_codec: num_steps = 0 for NID=0x9
[ 40.300365] hda_codec: num_steps = 0 for NID=0x9
[ 40.304601] hda_codec: num_steps = 0 for NID=0x9
[ 40.308824] hda_codec: num_steps = 0 for NID=0x9
[ 40.638949] ohci1394: $Rev: 1299 $ Ben Collins <bcollins at debian.org>
[ 40.638978] PCI: Via IRQ fixup for 0000:02:04.0, from 9 to 5
[ 40.695383] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]
MMIO=[febff000-febff7ff] Max Packet=[2048]
[ 41.338951] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc000068bada]
[ 41.634999] Real Time Clock Driver v1.12
[ 41.698350] input: PC Speaker
[ 41.848755] FDC 0 is a post-1991 82077
[ 42.966018] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 42.984709] NET: Registered protocol family 17
[ 45.141376] hda_codec: num_steps = 0 for NID=0x9
[ 45.145359] hda_codec: num_steps = 0 for NID=0x9
[ 45.149334] hda_codec: num_steps = 0 for NID=0x9
[ 45.153208] hda_codec: num_steps = 0 for NID=0x9
[ 45.157092] hda_codec: num_steps = 0 for NID=0x9
[ 45.160989] hda_codec: num_steps = 0 for NID=0x9
[ 45.164897] hda_codec: num_steps = 0 for NID=0x9
[ 45.168865] hda_codec: num_steps = 0 for NID=0x9
[ 45.172757] hda_codec: num_steps = 0 for NID=0x9
[ 45.176731] hda_codec: num_steps = 0 for NID=0x9
[ 45.180756] hda_codec: num_steps = 0 for NID=0x9
[ 45.184838] hda_codec: num_steps = 0 for NID=0x9
[ 45.188727] hda_codec: num_steps = 0 for NID=0x9
[ 45.192650] hda_codec: num_steps = 0 for NID=0x9
[ 45.196538] hda_codec: num_steps = 0 for NID=0x9
[ 45.200479] hda_codec: num_steps = 0 for NID=0x9
[ 45.204425] hda_codec: num_steps = 0 for NID=0x9
[ 45.208374] hda_codec: num_steps = 0 for NID=0x9
[ 45.790373] NET: Registered protocol family 10
[ 45.790473] Disabled Privacy Extensions on device c033f640(lo)
[ 45.790605] IPv6 over IPv4 tunneling driver
[ 51.258401] eth0: no IPv6 routers present
[ 52.194883] nvidia: module license 'NVIDIA' taints kernel.
[ 52.204446] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 52.204789] NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7676
Fri Jul 29 12:58:54 PDT 2005
[ 54.752498] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 55.817986] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version
1.50.3)
[ 55.825870] powernow-k8: BIOS error - no PSB or ACPI _PSS objects
[ 64.478660] hda_codec: num_steps = 0 for NID=0x9
[ 69.503634] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 69.505913] ISOFS: changing to secondary root
[ 72.961627] hda_codec: num_steps = 0 for NID=0x9
--
Configure bugmail: http://bugzilla.ubuntu.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the QA contact for the bug, or are watching the QA contact.
More information about the kernel-bugs
mailing list