[Bug 1770082] Re: systemd-networkd not renaming devices on boot

[Mathieu Trudel-Lapierre]

I'm not completely sure where the code lives in cloud-init; it looks a
bit like what's in:

cloudinit/net/netplan.py

But the code does read as though it should not be running 'udevadm test-
builtin net_setup_link'. However, deploying a system with MAAS shows a
/etc/cloud/cloud.cfg.d/50-curtin-networking.cfg file, which contains
data referring to the network interfaces:

network:
  config:
  - id: ens6
    mac_address: 52:54:00:31:27:2c
    mtu: 1500
    name: ens6
    subnets:
    - address: 10.3.99.13/24
      gateway: 10.3.99.1
      type: static
    type: physical
  version: 1

With that file in place, any netplan config renaming the interface to
something other than ens6 will see the interface being renamed *again*
back to ens6, when that file is removed, this behavior does not appear.

-- 
You received this bug notification because you are a member of Ubuntu
Foundations Bugs, which is subscribed to systemd in Ubuntu.
https://bugs.launchpad.net/bugs/1770082

Title:
  systemd-networkd not renaming devices on boot

Status in netplan:
  Confirmed
Status in cloud-init package in Ubuntu:
  Confirmed
Status in systemd package in Ubuntu:
  Confirmed

Bug description:
  === systemd issue ===

  Renaming devices doesn't seem to work.

  If I disable all other network configuration and create
  /etc/systemd/network/10-network.link with:

  [Match]
  MACAddress=52:54:00:c1:c9:bb

  [Link]
  Name=myiface3

  I expect this to cause the device with that MAC address to be renamed
  to  myiface3. However, when I reboot, I instead see:

  $ ip l
  1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
      link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
  2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
      link/ether 52:54:00:c1:c9:bb brd ff:ff:ff:ff:ff:ff

  The device is not renamed.

  This link file is pretty much identical to Example 2 in
  https://www.freedesktop.org/software/systemd/man/systemd.link.html.

  The renaming does work if I boot with net.ifnames=0, and oddly, it
  also works if I unbind the device and rebind it as netplan apply does.
  No setting of NamePolicy seems to help.

  === Original Bug ==

  'set-name:' doesn't change the name of a network interface on boot, it
  only works when you do netplan apply.

  Say I take this 50-cloud-init.yaml file:

  # This file is generated from information provided by
  # the datasource.  Changes to it will not persist across an instance.
  # To disable cloud-init's network configuration capabilities, write a file
  # /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following:
  # network: {config: disabled}
  network:
      version: 2
      ethernets:
          ens3:
              dhcp4: true
              match:
                  macaddress: 52:54:00:de:bd:f6
              set-name: ens3

  Say I change set-name to 'myiface3' and reboot. I expect that the
  device will be called myiface3 and brought up fine with dhcp. However,
  instead I see:

  $ ip a
  1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
      link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
      inet 127.0.0.1/8 scope host lo
         valid_lft forever preferred_lft forever
      inet6 ::1/128 scope host
         valid_lft forever preferred_lft forever
  2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
      link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff

  The name has not been changed, and the device has not been brought up.

  If I run netplan apply however, I see the following:

  1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
      link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
      inet 127.0.0.1/8 scope host lo
         valid_lft forever preferred_lft forever
      inet6 ::1/128 scope host
         valid_lft forever preferred_lft forever
  3: myiface3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
      link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff
      inet 192.168.122.151/24 brd 192.168.122.255 scope global dynamic myiface3
         valid_lft 3575sec preferred_lft 3575sec
      inet6 fe80::5054:ff:fede:bdf6/64 scope link
         valid_lft forever preferred_lft forever

  So names are successfully changed with netplan apply.

  This seems to be some udev-related timing or priority issue that I'm
  still trying to hunt down.

  This breaks some forms of migration in certain cloud environments.

To manage notifications about this bug go to:
https://bugs.launchpad.net/netplan/+bug/1770082/+subscriptions